3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownESP32-C3-DevKit-RUST-2
Espressif Systems · development board · ESP32-C3-MINI-1
This page carries the board as a part, so a carrier board or a breakout molecule can place it: the header pinout as a symbol, the header pattern as a footprint, and a 3D model of the board standing on its headers.
Footprint
J1 (16 pins) and J2 (12 pins) and J3 (2 pins) at 2.54 mm, from the board file (esp-rs/esp-rust-board tag v2.0, the RUST-2 design). The kit ships with bare header holes. The footprint origin is the centre of the header pattern; F.Fab draws the board (22.86 x 63.50 mm) and the module.
Pinout
As printed on the board's silkscreen, with functions from Espressif's user guide. GPIO20/GPIO21: the board nets are IO20_RX and IO21_TX (U0RXD/U0TXD), which the guide's table swaps; the page follows the nets. Pin 1 of each header is at the module end.
J1
| No. | Name | Function |
|---|---|---|
| 1 | RST | EN / CHIP_PU |
| 2 | 3V3 | 3.3 V power supply |
| 3 | NC | Not connected |
| 4 | GND | Ground |
| 5 | 0 | GPIO0, ADC1_CH0, XTAL_32K_P |
| 6 | 1 | GPIO1, ADC1_CH1, XTAL_32K_N |
| 7 | 2 | GPIO2, ADC1_CH2 (strapping); WS2812 RGB LED |
| 8 | 3 | GPIO3, ADC1_CH3 |
| 9 | 4 | GPIO4, ADC2_CH0, MTMS |
| 10 | 5 | GPIO5, ADC2_CH1, MTDI |
| 11 | 6 | GPIO6, MTCK |
| 12 | 7 | GPIO7, MTDO |
| 13 | 8 | GPIO8 (strapping), I2C SCL |
| 14 | 21 | GPIO21, U0TXD |
| 15 | 20 | GPIO20, U0RXD |
| 16 | 9 | GPIO9 (strapping), BOOT button |
J2
| No. | Name | Function |
|---|---|---|
| 1 | BAT+ | Battery supply |
| 2 | EN | Enable |
| 3 | 5V | USB VBUS |
| 4 | NC | Not connected |
| 5 | NC | Not connected |
| 6 | NC | Not connected |
| 7 | NC | Not connected |
| 8 | NC | Not connected |
| 9 | 18 | GPIO18, USB_D- |
| 10 | 19 | GPIO19, USB_D+ |
| 11 | NC | Not connected |
| 12 | NC | Not connected |
J3
| No. | Name | Function |
|---|---|---|
| 1 | BAT+ | Battery supply (battery pads below the right header) |
| 2 | BAT- | Battery return (ground) |
3D model
Built from the board file itself (esp-rs/esp-rust-board tag v2.0, the RUST-2 design): the real outline, mask and silkscreen, every pad, and each part at its board position. Each part with an Adom page carries that page's model, fitted to its pads on the board (worst fit 0.11 mm); the rest are KiCad library models fitted the same way. The module is adom/esp32-c3-mini-1-n4. The kit ships with bare header holes, so no headers are drawn. The solder mask is black, as the board file's stackup and Espressif's photo show.
- L1 (Sunlord SPH4018H2R2MT, LCSC C370436 in the esp-rs BOM): its model follows Sunlord's own drawing, a square moulded body with the inductance code 2R2 printed on top. The round-looking top in Espressif's photo is not in that drawing.
- Y1: the board names only 32.768 kHz in a 3.2 x 1.5 mm package (no part number), so it carries KiCad's 3215 crystal model and no page.
- C12, C13 and R12 are DNP on Espressif's schematic and in the board file: their pads are bare on purpose. TP2 (IMU_INT2) is a bare test pad.
Parts on the board
| Ref | Part | Page | 3D model |
|---|---|---|---|
| C1 | 10nF | adom/10n-0402-capacitors | KiCad library |
| C2 | 10nF | adom/10n-0402-capacitors | KiCad library |
| C3 | 100nF | adom/100n-0402-capacitors | KiCad library |
| C4 | 100nF | adom/100n-0402-capacitors | KiCad library |
| C5 | 10uF | adom/10u-0805-capacitors | KiCad library |
| C6 | 22pF | adom/22p-0603-capacitors | KiCad library |
| C7 | 10uF | adom/10u-0805-capacitors | KiCad library |
| C8 | 1uF | adom/1u-0402-capacitors | KiCad library |
| C9 | 100nF | adom/100n-0402-capacitors | KiCad library |
| C10 | 1uF | adom/1u-0402-capacitors | KiCad library |
| C11 | 10nF | adom/10n-0402-capacitors | KiCad library |
| C12 | DNP | (none) | not populated (DNP) (C12 is not populated on the shipped board (value DNP on Espressif schematic esp32-c3-devkit-rust-2-schematic.pdf and in the board file); footprint shown bare on purpose.) |
| C13 | DNP | (none) | not populated (DNP) (C13 is not populated on the shipped board (value DNP on Espressif schematic esp32-c3-devkit-rust-2-schematic.pdf and in the board file); footprint shown bare on purpose.) |
| C14 | 1nF | adom/1n-0402-capacitors | KiCad library |
| C15 | 4.7uF | adom/4-7u-0603-capacitors | KiCad library |
| C16 | 4.7uF | adom/4-7u-0603-capacitors | KiCad library |
| D1 | LESD8D3.3CAT5G |
adom/lesd8d3-3cat5g | adom page (factory model) |
| D2 | KT-0603R (LED) |
adom/kt-0603r | adom page (factory model) |
| D3 | KT-0603R (LED) |
adom/kt-0603r | adom page (factory model) |
| D4 | B5819W SL (B5819W) |
adom/b5819w-sl | adom page (factory model) |
| D5 | LESD5D5.0CT1G |
adom/lesd5d5-0ct1g | adom page (factory model) |
| D6 | B5819W SL (B5819W) |
adom/b5819w-sl | adom page (factory model) |
| D7 | LESD5D5.0CT1G |
adom/lesd5d5-0ct1g | adom page (factory model) |
| D8 | LESD5D5.0CT1G |
adom/lesd5d5-0ct1g | adom page (factory model) |
| D9 | WS2812B-MINI-V3/W (WS2812B) |
adom/ws2812b-mini-v3-w | adom page (factory model) |
| J1 | USB4105-GF-A |
adom/usb4105-gf-a | adom page (factory model) |
| L1 | SPH4018H2R2MT (SPH4018H2R2MT (2.2uH 2.2A)) |
adom/sph4018h2r2mt | adom page (factory model) |
| Q1 | DMG3415U-7 (DMG3415U) |
adom/dmg3415u-7 | adom page (factory model) |
| R1 | 10k | adom/10k-0402-resistors | KiCad library |
| R2 | 100k | adom/100k-0402-resistors | KiCad library |
| R3 | 22.1k | adom/22-1k-0402-resistors | KiCad library |
| R4 | 5.1k | adom/5-1k-0402-resistors | KiCad library |
| R5 | 0 | adom/0p-0402-resistors | KiCad library |
| R6 | 5.1k | adom/5-1k-0402-resistors | KiCad library |
| R7 | 0 | adom/0p-0402-resistors | KiCad library |
| R8 | 10k | adom/10k-0402-resistors | KiCad library |
| R9 | 10k | adom/10k-0402-resistors | KiCad library |
| R10 | 470 | adom/470-0402-resistors | KiCad library |
| R11 | 0 | adom/0p-0402-resistors | KiCad library |
| R12 | DNP | (none) | not populated (DNP) (R12 is not populated on the shipped board (value DNP on Espressif schematic esp32-c3-devkit-rust-2-schematic.pdf and in the board file); footprint shown bare on purpose.) |
| R14 | 1k | adom/1k-0402-resistors | KiCad library |
| R15 | 100k | adom/100k-0402-resistors | KiCad library |
| R17 | 10k | adom/10k-0402-resistors | KiCad library |
| R18 | 10k | adom/10k-0402-resistors | KiCad library |
| R19 | 10k | adom/10k-0402-resistors | KiCad library |
| SW1 | PTS810SJM250SMTRLFS (SW_Push) |
adom/pts810sjm250smtrlfs | adom page (factory model) |
| SW2 | PTS810SJM250SMTRLFS (SW_Push) |
adom/pts810sjm250smtrlfs | adom page (factory model) |
| TP2 | IMU_INT2 test pad | (none) | not populated (DNP) (TP2 (IMU_INT2) is a bare test pad by design.) |
| U1 | SHTC3-TR-2.5KS (SHTC3) |
adom/shtc3-tr-2-5ks | adom page (factory model) |
| U2 | ICM-42670-P |
adom/icm-42670-p | adom page (factory model) |
| U3 | ESP32-C3-MINI-1-N4 (ESP32-C3-MINI-1) |
adom/esp32-c3-mini-1-n4 | adom page (factory model) |
| U4 | edge pads (header holes) | (none) | not populated (DNP) (U4 is the edge pad row (header holes); the kit ships without headers, so none are drawn.) |
| U5 | SY8088IAAC (SY8088) |
adom/sy8088iaac | adom page (factory model) |
| U6 | MCP73831T-2ACI/OT |
adom/mcp73831t-2aci-ot | adom page (factory model) |
| Y1 | 32.768Hz | (none) | KiCad library |
Documents
- User guide (Espressif, web)
- Module datasheet (ESP32-C3-MINI-1): docs/esp32-c3-devkit-rust-2-datasheet.pdf, from Espressif
- Board file: docs/esp-rust-board-v2.0.kicad_pcb, from esp-rs/esp-rust-board v2.0 (CERN-OHL)