3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownICM-42670-P
TDK InvenSense · Accelerometers · LGA-14(2.5x3)
ICM-42670-P from TDK InvenSense, in a LGA-14(2.5x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AP_SDO / AP_AD0 | output | AP_SDO is the AP SPI serial data output in 4-wire mode, and AP_AD0 is the AP I3CSM / I2C slave address LSB. |
| 2 | RESV | unconnected | Reserved pin: no connect, or connect to GND or VDDIO. |
| 3 | RESV | unconnected | Reserved pin: no connect, or connect to GND or VDDIO. |
| 4 | INT1 / INT | output | INT1 is interrupt 1 and can be push-pull or open drain; when used as INT, all interrupts are mapped to this pin. |
| 5 | VDDIO | power_in | IO power supply voltage, operating range 1.71V to 3.6V. |
| 6 | GND | power_in | Power supply ground. |
| 7 | FSYNC | input | Frame sync input; connect to GND if FSYNC is not used. |
| 8 | VDD | power_in | Power supply voltage, operating range 1.71V to 3.6V. |
| 9 | INT2 | output | INT2 is interrupt 2 and can be push-pull or open drain. |
| 10 | RESV | unconnected | Reserved pin: no connect, or connect to GND or VDDIO. |
| 11 | RESV | unconnected | Reserved pin: no connect, or connect to GND or VDDIO. |
| 12 | AP_CS | input | AP SPI chip select; connect to VDDIO when using the AP I3CSM / I2C interface. |
| 13 | AP_SCL / AP_SCLK | input | AP_SCL is the AP I3CSM / I2C serial clock, and AP_SCLK is the AP SPI serial clock. |
| 14 | AP_SDA / AP_SDIO / AP_SDI | bidirectional | AP_SDA is the AP I3CSM / I2C serial data, AP_SDIO is the AP SPI serial data I/O in 3-wire mode, and AP_SDI is the AP SPI serial data input in 4-wire mode. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TDK InvenSense |
| Package | LGA-14(2.5x3) |
| Category | Sensors |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Sensitivity Scale Factor Initial Tolerance | -1 | 1 | % | 25°C | 10 | ||
| Sensitivity Scale Factor Variation Over Temperature | -0.007 | 0.007 | %/ºC | -40°C to +85°C; Board-Level | 10 | ||
| Nonlinearity (gyroscope) | -0.1 | 0.1 | % | Best fit straight line; 25°C; Board-Level | 10 | ||
| Cross-Axis Sensitivity (gyroscope) | -2 | 2 | % | Board-level | 10 | ||
| Initial ZRO Tolerance | -1 | 1 | º/s | 25°C | 10 | ||
| ZRO Variation vs. Temperature | -0.015 | 0.015 | º/s/ºC | -40°C to +85°C; Board-Level | 10 | ||
| Gyroscope Mechanical Frequencies | 25 | 28 | 30 | kHz | 10 | ||
| Low Pass Filter Response (gyroscope) | 16 | 180 | Hz | 10 | |||
| Output Data Rate (gyroscope) | 12.5 | 1600 | Hz | 10 | |||
| Sensitivity Scale Factor Initial Tolerance (accelerometer) | -1 | 1 | % | 25°C | 11 | ||
| Sensitivity Change vs. Temperature | -0.01 | 0.01 | %/ºC | -40°C to +85°C; Board-Level | 11 | ||
| Nonlinearity (accelerometer) | -0.1 | 0.1 | % | Best Fit Straight Line, ±2g; Board-Level | 11 | ||
| Cross-Axis Sensitivity (accelerometer) | -1 | 1 | % | Board-level | 11 | ||
| Zero-G Initial Tolerance | -25 | 25 | mg | 25°C | 11 | ||
| Zero-G Level Change vs. Temperature | -0.15 | 0.15 | mg/ºC | -40°C to +85°C; Board-Level | 11 | ||
| Low Pass Filter Response (accelerometer) | 16 | 180 | Hz | 11 | |||
| Output Data Rate (accelerometer) | 1.5625 | 1600 | Hz | 11 | |||
| VDD | VDD | 1.71 | 1.8 | 3.6 | V | 12 | |
| VDDIO | VDDIO | 1.71 | 1.8 | 3.6 | V | 12 | |
| Specified Temperature Range | -40 | 85 | °C | 12 | |||
| Supply Ramp Time | 0.1 | 3 | ms | Valid power-on RESET | 13 | ||
| Temperature Sensor Operating Range | -40 | 85 | °C | Ambient | 13 | ||
| ODR With Filter (temperature sensor) | 1.5625 | 1600 | Hz | With Filter | 13 | ||
| Room Temperature Offset | -3 | 3 | °C | 25°C | 13 | ||
| Sensitivity Trimmed | 125 | 126.9 | 129 | LSB/°C | Trimmed | 13 | |
| Sensitivity for FIFO data | 1.95 | 1.983 | 2.01 | LSB/°C | Trimmed | 13 | |
| VOL.INT, INT Low-Level Output Voltage | VOL.INT | 0.1 | V | OPEN=1, 0.3 mA sink current | 13 | ||
| INT Pulse Width | tINT | 8 | 100 | µs | int_tpulse_duration= 0, 1 (100us, 8us) | 13 | |
| Input Capacitance | CI | 10 | pF | 13 | |||
| VOL, LOW-Level Output Voltage (I2C) | VOL | 0 | 0.4 | V | 3 mA sink current | 13 | |
| Output Fall Time (I2C) | tof | 300 | ns | from VIHmax to VILmax; Cb bus capacitance in pF | 13 | ||
| Clock Frequency Initial Tolerance | -3 | 3 | % | CLKSEL=2b00 or gyro inactive; 25°C | 13 | ||
| Clock Frequency Initial Tolerance | -1 | 1 | % | CLKSEL=2b01 and gyro active; 25°C | 13 | ||
| Frequency Variation over Temperature | -3 | 3 | % | CLKSEL=2b00 or gyro inactive; -40°C to +85°C | 13 | ||
| Frequency Variation over Temperature | -1 | 1 | % | CLKSEL=2b01 and gyro active; -40°C to +85°C | 13 | ||
| fSCL, SCL Clock Frequency | fSCL | 1 | MHz | I2C fast-mode plus | 14 | ||
| fSPC, SCLK Clock Frequency | fSPC | 24 | MHz | Default | 15 | ||
| Supply Voltage VDD | VDD | -0.5 | 4 | V | 17 | ||
| Supply Voltage VDDIO | VDDIO | -0.5 | 4 | V | 17 | ||
| Acceleration (Any Axis, unpowered) | 20000 | g | 0.2 ms | 17 | |||
| Operating Temperature Range | -40 | 85 | °C | 17 | |||
| Storage Temperature Range | -40 | 125 | °C | 17 | |||
| Electrostatic Discharge Protection (HBM) | 2 | kV | HBM | 17 | |||
| Electrostatic Discharge Protection (CDM) | 500 | V | CDM | 17 | |||
| Latch-up | -100 | 100 | mA | JEDEC Class II, 125°C | 17 |
CAD (KiCad official)
- Symbol:
ICM-42670-P - Footprint:
Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm - 3D model: LGA-14(2.5x3) (KiCad packages3D, STEP)
- 3D model files:
icm-42670-p-etched.step/icm-42670-p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);icm-42670-p.step/icm-42670-p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TDK InvenSense datasheet (103 pp, sha256
8716d8187abf2f89, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).