board

65% MX Keyboard (soldered)

Public Unreviewed

by gzc

65% ANSI keyboard PCB (68 soldered MX switches) for a gasket-mount case, rev B: STM32F072 under the spacebar running QMK, USB through a Unified Daughterboard on a Pico-EZmate cable, strict-grid copper, green with lead-free HASL, PCBWay bare board for hand assembly.

keyboard65-percentsolderedstm32qmkkicadgasket-mountpcbway
Overview Files Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity
main
65-keyboard / README.md
History Download
gzc Revision B: soldered MX switches (no hotswap), PCBWay bare board for hand assembly, green mask with lead-free HASL; new… b097cd0 16h ago

65% MX Keyboard (soldered)

A 65% ANSI keyboard main board (68 keys) for a gasket-mount case. The MX switches solder straight into the board, an STM32F072 under the spacebar runs QMK, and USB comes in through a separate USB-C daughterboard on a 4-pin Molex Pico-EZmate cable. The copper is laid out on a strict grid: one straight line per row, one vertical line per column. Made by PCBWay as a bare board and soldered by hand.

Status: revision B, designed and checked, not yet built. The schematic and board match pin for pin (353 of 353), KiCad DRC and ERC are clean (0 errors, 0 unconnected), and the current and heat screen passes. Nothing on this page has been measured on a real board yet.

What changed from rev A: soldered MX switches instead of Kailh hotswap sockets, PCBWay bare board for hand assembly instead of JLCPCB assembly, green mask with lead-free HASL instead of matte black with ENIG. The layout, controller, USB daughterboard and pin map are unchanged.

Back of the green board in 3D: the soldered switch pins, a diode below each switch, the STM32 controller, regulator and USB header under the spacebar The back of the board (KiCad render, green mask, lead-free HASL). Every small part is on this side; the switches go in from the front and are soldered here.

At a glance
Layout 65% ANSI, 68 keys, 16u x 5u at 19.05 mm pitch
Board 304.8 x 96.75 mm, 2 layers, 1.6 mm, green mask, white silkscreen, lead-free HASL
Switches MX-style, soldered: 5-pin (PCB-mount) or 3-pin (plate-mount), your choice
Stabilizers PCB screw-in (Durock V2): 6.25u Space, 2u Backspace, 2.25u Enter, 2.25u Left Shift
Matrix 5 rows x 15 columns, 1N4148WS (SOD-323) per key, COL2ROW
Controller STM32F072CBT6, crystal-less USB, built-in DFU bootloader
Firmware QMK + VIA/Vial (stm32-dfu)
USB Unified Daughterboard (UDB-C, EZM type) on a 1:1 Pico-EZmate cable into J2
Fab PCBWay, bare board (no assembly); 0.25 mm tracks, 0.2 mm gaps, well above PCBWay's limits
Mounting 8 x M2 holes kept for now; a gasket case may use none

Pictures

Back of the board seen flat: a diode below every switch, five straight row lines and the controller block under the spacebar Back, flat. Each diode sits below its switch, all facing the same way; each row is one straight line.

Front of the board seen flat with 68 MX switches seated Front, flat, with the switch 3D models seated. No silkscreen boxes on this side; the column traces show faintly under the mask.

Close-up of the controller area: J2 header, AP2112K regulator, STM32F072, BOOT and RESET buttons and the labelled test pads The controller block under the spacebar: J2 (USB cable header), the 3.3 V regulator, the STM32, the BOOT (SW69) and RESET (SW70) buttons, and the test pads, each labelled with its net.

The two copper layers drawn separately: back copper in blue with straight rows and short hooks from each switch to its diode, front copper in red with vertical columns into each switch pin The copper, layer by layer. Back (blue): straight rows, a short hook from each switch pin to its diode, and the 15 columns arriving at the chip as two bundles. Front (red): one vertical column per key column, straight into each switch pin (the pins are plated, so no vias are needed per key).

Adom Fields current and heat solve of the rev B board, with VBUS 0.5 A at 40 A/mm2 and the issues list Adom Fields current and heat screen (simulation, 0.5 A on VBUS and GND): peak 40 A/mm², under 1 °C rise, 0.9 mV ground offset. The "no TVS" tag on J2 is expected: ESD protection lives on the daughterboard. The three low notes left open are listed in the design review.

Plan drawing comparing two controller spots: A by the Enter key and B under the spacebar How the controller spot was chosen (rev A, unchanged): A (by Enter) left no room for the column bundles, so B (under the spacebar) was built.

Building it

  • Order: upload the Gerber zip (made from the KiCad project; not published here) to PCBWay: 2 layers, 1.6 mm, green mask, white silkscreen, lead-free HASL, 1 oz copper, no assembly. PCBWay prints an order number on the board unless you pick a location or pay to leave it off.
  • Parts: the shopping list has every part with quantities and spares; the order notes list the PCBWay settings. The STM32F072CBT6 had only 32 in stock at JLCPCB/LCSC on 2026-11-09; check stock and buy a spare.
  • Solder in this order: the STM32 first (pin 1 dot to the marked corner, drag-solder with lots of flux, check every pin for bridges), then the regulator, capacitors and resistor, the 68 diodes (stripe to the printed bar, all the same way), J2 and the two buttons. Test with the daughterboard (hold BOOT, tap RESET: the PC should see 0483:DF11), then stabilizers, plate and switches last.
  • Daughterboard: a Unified Daughterboard of the EZM (Pico-EZmate) type with its 1:1 cable: pin 1 VBUS, 2 D-, 3 D+, 4 GND. The main board has no ESD or fuse of its own; the daughterboard carries them.
  • QMK pins: MATRIX_ROW_PINS { PB9, PB6, PB4, PA15, PB3 }, MATRIX_COL_PINS { PA0, PA1, PA2, PA3, PA4, PA5, PA6, PA7, PB0, PB1, PB2, PB10, PB11, PB12, PB13 }, DIODE_DIRECTION COL2ROW.
  • Debug: SWD on the test pads: 3V3, SWDIO, SWCLK, NRST, GND (plus VBUS and BOOT0).

Design review and datasheet

  • Design review: the current and heat tables, the screens' verdicts and the parts table.
  • Datasheet (PDF): operating envelope, pinout, power, mechanical and fab details, hand assembly and the qualification limits. It is at the bottom of this page too.

Components

References Qty Value MPN Manufacturer Wiki page
J2 1 Pico-EZmate 4P 78171-0004 Molex project library (no public page yet)
U3 1 AP2112K-3.3 AP2112K-3.3TRG1 Diodes Incorporated adom/ap2112k-3-3trg1
C1, C2, C8 3 1uF CL10A105KB8NNNC Samsung Electro-Mechanics project library (no public page yet)
U1 1 STM32F072CBT6 STM32F072CBT6 STMicroelectronics adom/stm32f072cbt6
C3, C4, C5, C6, C10 5 100nF CC0603KRX7R9BB104 YAGEO glenn/cc0603krx7r9bb104
C7 1 4.7uF CL10A475KO8NNNC Samsung Electro-Mechanics adom/cl10a475ko8nnnc
C9 1 10nF 0603B103K500NT FH (Guangdong Fenghua) project library (no public page yet)
R3 1 10k 0603WAF1002T5E UNI-ROYAL adom/0603waf1002t5e
SW69, SW70 2 BOOT TS-1187A-B-A-B XKB Connection adom/ts-1187a-b-a-b
SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23, SW24, SW25, SW26, SW27, SW28, SW29, SW30, SW31, SW32, SW33, SW34, SW35, SW36, SW37, SW38, SW39, SW40, SW41, SW42, SW43, SW44, SW45, SW46, SW47, SW48, SW49, SW50, SW51, SW52, SW53, SW54, SW55, SW56, SW57, SW58, SW59, SW60, SW61, SW62, SW63, SW64, SW65, SW66, SW67, SW68 68 MX_SWITCH MX switch, 5-pin or 3-pin (user-supplied) any MX-compatible (your choice) not on the wiki yet
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25, D26, D27, D28, D29, D30, D31, D32, D33, D34, D35, D36, D37, D38, D39, D40, D41, D42, D43, D44, D45, D46, D47, D48, D49, D50, D51, D52, D53, D54, D55, D56, D57, D58, D59, D60, D61, D62, D63, D64, D65, D66, D67, D68 68 1N4148WS 1N4148WS onsemi project library (no public page yet)

Install every part in KiCad

This page is a KiCad Plugin and Content Manager repository. In KiCad, open Plugin and Content Manager, Manage..., add this URL, then install 65% MX keyboard (soldered), rev B from the Libraries tab:

https://wiki.adom.inc/api/pages/gzc/65-keyboard/files/pcm/repository.json

The library appears as PCM_65-keyboard (package inc.adom.wiki.gzc.65-keyboard): every symbol, footprint and 3D model of this board, from the parts' wiki pages.

How this board was built

Every step of the build, in order, each with its own page of evidence (checks, screenshots, the AI's drawings and usage), written by adom-aiflow as the run went.

2. Design rules: choose the fab, load its design rules. The evidence

3. Components: wiki component identity and CAD audit. The evidence

4. Libraries: the project library in the EDA. The evidence

5. 3D models: every 3D model bound and upright. The evidence

6. Test plan: what to measure on the workcell, a probe spot for each. The evidence

7. Placement: parts placed for current and heat. The evidence

8. Routing: every trace routed, DRC clean. The evidence

9. Heatsink vias: via arrays under the hot parts. The evidence

10. Copper pours: copper pours and stitching. The evidence

11. Rounded corners: sharp board corners rounded. The evidence

12. Current: current density on every loaded net. The evidence

13. Thermal: temperature rise against the budget. The evidence

14. Fields: current and heat solved in 3D. The evidence

15. Pour walkthrough: each pour net lit in turn. The evidence

16. Silkscreen: labels, polarity, pinouts, both faces. The evidence

17. 3D board: the finished board in 3D. The evidence

18. Finish line: 0 unconnected, 0 errors, every check passed. The evidence

19. Gerbers, BOM, CPL: manufacturing files written and checked. The evidence