main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers tlk105lrhbt: viewers · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
tlk105lrhbt-etched.glb tlk105lrhbt: factory component page (tier=lcsc) · Ray
tlk105lrhbt-etched.step tlk105lrhbt: factory component page (tier=lcsc) · Ray
tlk105lrhbt-hero.glb tlk105lrhbt: hero GLB from the etched model (keeps the MPN mark) · Ray
tlk105lrhbt-hero.overlay.json Publish 0.1.0 · Ray
tlk105lrhbt.glb Publish 0.1.0 · Ray
tlk105lrhbt.kicad_mod Publish 0.1.0 · Ray
tlk105lrhbt.kicad_sym Publish 0.1.0 · Ray
tlk105lrhbt.lbr Publish 0.1.0 · Ray
tlk105lrhbt.step Publish 0.1.0 · Ray

TLK105LRHBT

Texas Instruments · Ethernet Transceivers · VQFN-32(5x5)

TLK105LRHBT from Texas Instruments, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RXD_3 / PHYAD4 output Receive data bit 3 for MII mode, synchronous to RX_CLK, multiplexed with PHY address bit PHYAD4 which is latched at power-up and hardware reset and is pulled down by default.
2 TX_CLK output MII transmit clock providing a 25 MHz or 2.5 MHz reference depending on speed; unused in RMII mode.
3 TX_EN input Transmit enable, presented on the rising edge of TX_CLK, indicating valid TXD data, active high; TXD[3:0] in MII mode and TXD[1:0] in RMII mode.
4 TXD_0 input Transmit data bit 0 from the MAC, synchronous to TX_CLK in MII mode or to the 50 MHz XI reference in RMII mode.
5 TXD_1 input Transmit data bit 1 from the MAC, synchronous to TX_CLK in MII mode or to the 50 MHz XI reference in RMII mode.
6 TXD_2 input Transmit data bit 2 from the MAC, used in MII mode, synchronous to TX_CLK.
7 TXD_3 input Transmit data bit 3 from the MAC, used in MII mode, synchronous to TX_CLK.
8 INT / PWDN bidirectional Default function is active-low power-down input; when set as interrupt it is an open-drain output with weak internal pull-up that may need an external pull-up, and register access is required to select the function.
9 RD- bidirectional Differential receive input (PMD input pair) automatically configured for 10Base-T or 100Base-TX, requires 3.3 V bias, and can be used as transmit output in Auto-MDIX mode.
10 RD+ bidirectional Differential receive input (PMD input pair) automatically configured for 10Base-T or 100Base-TX, requires 3.3 V bias, and can be used as transmit output in Auto-MDIX mode.
11 TD- bidirectional Differential transmit output (PMD output pair) automatically configured for 10Base-T or 100Base-TX, requires 3.3 V bias, and can be used as receive input in Auto-MDIX mode.
12 TD+ bidirectional Differential transmit output (PMD output pair) automatically configured for 10Base-T or 100Base-TX, requires 3.3 V bias, and can be used as receive input in Auto-MDIX mode.
13 PFBIN1 input Power feedback input fed from PFBOUT in single-supply operation, or connected to a 1.55 V external supply in multiple-supply operation with a 0.1 µF capacitor close to the pin.
14 AVDD33 power_in Analog 3.3 V power supply.
15 PFBOUT output Power feedback output with 10 µF and 0.1 µF ceramic capacitors placed close to it; connected to PFBIN1 and PFBIN2 in single-supply operation and not used in multiple-supply operation.
16 RBIAS input Bias resistor connection, using a 4.87 kΩ 1% resistor connected from RBIAS to GND.
17 LED_LINK (MLED) / AN_0 output LED pin indicating link status (Mode 1) or link with activity blink (Mode 2); AN_0 is also a power-up/reset strap that selects the advertised duplex mode.
18 RESET input Active-low reset input; asserting low for at least 1 µs reinitializes all internal registers and re-latches the jumper options.
19 MDIO bidirectional Management data I/O synchronized to MDC, which may be driven by the controller or the TLK10xL, and requires a 2.2 kΩ pull-up resistor.
20 MDC input Management data clock with a maximum rate of 25 MHz and no minimum rate, not required to be synchronous to TX_CLK or RX_CLK.
21 VDD_IO power_in Digital I/O supply of 3.3 V (3.0 to 3.6 V), 2.5 V (2.25 to 2.75 V), or 1.8 V (1.62 to 1.98 V, MII mode only).
22 XO output Crystal output for a 25 MHz crystal only; leave floating when an oscillator drives XI.
23 XI input Crystal or CMOS oscillator input: 25 MHz ±50 ppm in MII mode, or 50 MHz ±50 ppm CMOS oscillator in RMII mode, with the oscillator referenced to the VDD_IO voltage (RMII not supported with 1.8 V reference).
24 PFBIN2 input Power feedback input fed from PFBOUT in single-supply operation, or connected to a 1.55 V external supply in multiple-supply operation with a 0.1 µF capacitor close to the pin.
25 RX_CLK output MII receive clock providing 25 MHz or 2.5 MHz depending on speed, derived from the received data stream.
26 RX_DV / MII_MODE output Receive data valid indicating valid RXD data independent of carrier sense; also a power-up configuration strap for MII_MODE.
27 CRS / CRS_DV / LED_CFG output Carrier sense asserted when the MII receive medium is non-idle, or combined carrier sense and receive data valid in RMII mode; also the LED_CFG strap.
28 RX_ER / AMDIX_EN output Receive error indication synchronous to RX_CLK in MII mode or XI in RMII mode, not required by the MAC because the PHY corrupts data on receive error; also the AMDIX_EN strap.
29 COL (MLED) / PHYAD0 output Collision detect, always low in full duplex and not used in RMII mode; multiplexed with the PHYAD0 LSB address input (pulled up) and can carry the MLED output.
30 RXD_0 / PHYAD1 output Receive data bit 0 synchronous to RX_CLK, valid when RX_DV is asserted; multiplexed with PHY address bit PHYAD1 (pulled down).
31 RXD_1 / PHYAD2 output Receive data bit 1 synchronous to RX_CLK, valid when RX_DV is asserted (RMII uses RXD[1:0]); multiplexed with PHY address bit PHYAD2 (pulled down).
32 RXD_2 / PHYAD3 output Receive data bit 2 synchronous to RX_CLK, part of the MII RXD[3:0] nibble; multiplexed with PHY address bit PHYAD3 (pulled down).
33 GND power_in Ground exposed pad (DOWN_PAD); it must be soldered down to achieve the stated ESD rating on the Ethernet network pins.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-32(5x5)
Category Interface
Pins 33

CAD (KiCad official)

  • Symbol: TLK105LRHBT
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
  • 3D model files: tlk105lrhbt-etched.step / tlk105lrhbt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tlk105lrhbt.step / tlk105lrhbt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (114 pp, sha256 83ab6da6f71b8024, retrieved 2026-10-11, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF