skill
PCB Design Rules
Public Made by Adomby adom
Canonical PCB fab design rules (DRC) for every popular vendor: one JSON record per vendor, process and layer count, with generated Fusion/EAGLE .dru and .edru, KiCad .kicad_dru plus board-setup JSON, Altium .RUL exports, and a human comparison table. Every number cites the vendor's own capabilities page and the date it was read.
← All Pull Requests
Disable the all/all same-signal 'Same-net track spacing' rule: it reports every trace joint as an Overlap warning #1
Merged opened by John Lauer 2026-09-07
Merges
fix/same-net-track-spacing → mainEvery generated Fusion profile carries a Copper Clearance rule named "Same-net track spacing" with onescope/otherscope "all", samesignal="yes" and value max(spacing, 0.25 mm). Fusion's native DRC applies a same-signal clearance to touching copper too, so every place a trace meets its own pad, its own via or its next segment is at zero distance and is reported as an Overlap warning (code 19, type 2).
Measured today on the six-net routing fixture from adom/fusion-bridge (21 segments, 2 vias, 13 through-hole pads) with adom-instapcb-2L.edru loaded: 31 Overlap warnings, at the 13 pad entries and 18 trace/via joints, nothing near another net. With only this rule disabled and nothing else changed, native DRC on the identical board reports 0 errors, 0 warnings, 0 airwires. The routed board and the loaded rules are attached to adom/fusion-bridge#82.
This PR sets enabled="no" on that rule in tools/generate.py and regenerates the 53 fusion/*.edru files (nothing else in the output changes). The rule stays in the file, disabled, so a user who wants a same-net spacing check on parallel runs can switch it on knowingly; the built-in smd-to-pad, smd-to-via and smd-to-smd same-signal checks (builtin 6, 7, 8) are untouched. If a vendor spec actually states a same-net spacing, the right encoding is a rule scoped away from touching objects, which Fusion's rule scopes cannot express for wires; leaving it enabled makes every profile fail DRC on every routed board.
Diff Skip to comments
fusion/adom-instapcb-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/adom-instapcb-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-advanced-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-advanced-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-advanced-standard-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-3"/>
fusion/advanced-circuits-4pcb-advanced-standard-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1397mm" preferredvalue="0.2794mm" samesignal="no" name="copper-clearance-3"/>
fusion/aisler-enig-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-3"/>
fusion/aisler-enig-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.125mm" preferredvalue="0.25mm" samesignal="no" name="copper-clearance-3"/>
fusion/aisler-hasl-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-3"/>
fusion/allpcb-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/allpcb-advanced-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-3"/>
fusion/allpcb-advanced-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-3"/>
fusion/allpcb-advanced-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.076mm" preferredvalue="0.152mm" samesignal="no" name="copper-clearance-3"/>
fusion/elecrow-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/elecrow-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/elecrow-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/eurocircuits-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/eurocircuits-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/eurocircuits-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/eurocircuits-proto-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-3"/>
fusion/eurocircuits-proto-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.15mm" preferredvalue="0.3mm" samesignal="no" name="copper-clearance-3"/>
fusion/jlcpcb-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1mm" preferredvalue="0.2mm" samesignal="no" name="copper-clearance-3"/>
fusion/jlcpcb-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-3"/>
fusion/jlcpcb-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.09mm" preferredvalue="0.18mm" samesignal="no" name="copper-clearance-3"/>
fusion/macrofab-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/macrofab-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/macrofab-extended-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-3"/>
fusion/macrofab-extended-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-3"/>
fusion/nextpcb-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-3"/>
fusion/nextpcb-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-3"/>
fusion/nextpcb-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0762mm" preferredvalue="0.1524mm" samesignal="no" name="copper-clearance-3"/>
fusion/nextpcb-advanced-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0635mm" preferredvalue="0.127mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0635mm" preferredvalue="0.127mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0635mm" preferredvalue="0.127mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-2oz-0.8mm-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-after-dark-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/osh-park-flex-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1524mm" preferredvalue="0.3048mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-advanced-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-advanced-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-3"/>
fusion/pcbway-advanced-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.0508mm" preferredvalue="0.1016mm" samesignal="no" name="copper-clearance-3"/>
fusion/seeed-fusion-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/seeed-fusion-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/seeed-fusion-6L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/seeed-fusion-advanced-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.127mm" preferredvalue="0.254mm" samesignal="no" name="copper-clearance-3"/>
fusion/seeed-fusion-advanced-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/sierra-circuits-2L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
fusion/sierra-circuits-4L.edru+1−1@@ -32,7 +32,7 @@ <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="0.25mm" preferredvalue="0.25mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> <rule type="Copper Clearance" builtin_ruleid="0" enabled="yes" priority="1" onescope="is_wire_polygon" otherscope="is_wire_polygon" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-1"/> <rule type="Copper Clearance" builtin_ruleid="1" enabled="yes" priority="2" onescope="is_wire_polygon" otherscope="is_pad_smd" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-2"/> <rule type="Copper Clearance" builtin_ruleid="2" enabled="yes" priority="3" onescope="is_wire_polygon" otherscope="is_via" value="0.1016mm" preferredvalue="0.2032mm" samesignal="no" name="copper-clearance-3"/>
tools/generate.py+1−1@@ -183,7 +183,7 @@ def gen_edru(vendor, rec): <rule type="Wire Stub" builtin_ruleid="17" enabled="yes" priority="0" name="wire-stub-1"/> <rule type="Air-Wire" builtin_ruleid="19" enabled="yes" priority="0" name="air-wire-1"/> <rule type="Matched Lengths" builtin_ruleid="20" enabled="yes" priority="0" tolerance="10mm" gapfactor="2.5" name="matched-lengths-1"/>- <rule type="Copper Clearance" enabled="yes" priority="0" onescope="all" otherscope="all" value="{fmm(max(sp,0.25))}mm" preferredvalue="{fmm(max(sp,0.25))}mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/>+ <rule type="Copper Clearance" enabled="no" priority="0" onescope="all" otherscope="all" value="{fmm(max(sp,0.25))}mm" preferredvalue="{fmm(max(sp,0.25))}mm" samesignal="yes" bothscope="all" name="Same-net track spacing"/> {clearance_rules()} <rule type="Dimension Clearance" builtin_ruleid="9" enabled="yes" priority="0" value="{fmm(c2e)}mm" preferredvalue="{fmm(max(c2e, 0.4))}mm" name="dimension-clearance-1"/> <rule type="Via Restrict Clearance" builtin_ruleid="21" enabled="yes" priority="0" value="0mil" preferredvalue="0mil" name="via-restrict-clearance-1"/>
Comments
Log in to comment.
No comments yet.