main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs lm74910qrgerq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers lm74910qrgerq1: viewers · Ray
lm74910qrgerq1-etched.fit.json lm74910qrgerq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
lm74910qrgerq1-etched.glb lm74910qrgerq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
lm74910qrgerq1-etched.step lm74910qrgerq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
lm74910qrgerq1.glb Publish 0.1.0 · Ray
lm74910qrgerq1.kicad_mod Publish 0.1.0 · Ray
lm74910qrgerq1.kicad_sym Publish 0.1.0 · Ray
lm74910qrgerq1.lbr Publish 0.1.0 · Ray
lm74910qrgerq1.step Publish 0.1.0 · Ray
package.json lm74910qrgerq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json lm74910qrgerq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/lm74910qrgerq1 · Ray

LM74910QRGERQ1

Texas Instruments · Power Distribution Switches · VQFN-24-EP(4x4)

LM74910QRGERQ1 from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DGATE output Diode controller gate-drive output that connects to the gate of the external ideal-diode MOSFET.
2 A input Anode of the ideal diode; connects to the source of the external MOSFET (Q1) and is monitored for the AC-DC forward regulation and fast reverse-voltage comparator.
3 SW input Voltage-sense disconnect switch terminal internally connected to VSNS; used as the top connection for the battery-detect or OV resistor ladder and disconnects when EN is pulled low; short to VS if the internal switch is unused.
4 UVLO input Adjustable undervoltage threshold input; a resistor divider from SW to UVLO to GND sets the UVLO falling threshold that pulls HGATE low to turn off the HSFET.
5 OV input Adjustable overvoltage threshold input; a resistor divider from SW to OV sets the OV cutoff threshold that pulls HGATE low to turn off the HSFET.
6 EN input Enable input, typically tied to VS for always-on operation or driven externally; pulling it below V(ENF) places the device in the low-IQ shutdown mode.
7 SLEEP input Active-low sleep-mode input driven by a microcontroller; pulling it low turns off the charge pump and gate drivers and powers the output through an internal current-limited bypass switch.
8 NC unconnected No internal connection.
9 TMR input Fault timer input; a capacitor from TMR to GND sets the overcurrent-warning, fault (FLT), and retry timing, leaving it open sets the fastest timing, and tying it to GND disables overcurrent protection.
10 IMON output Analog current-monitor output that sources a scaled current through the external RSNS sense resistor; an external resistor to GND converts this current to a proportional voltage, and the pin should float if unused.
11 ILIM input Overcurrent detection set pin; a resistor from ILIM to GND sets the overcurrent comparator threshold, and ILIM should be tied to GND if overcurrent protection is not needed.
12 FLT output Open-drain fault output that is pulled low during a UVLO, OV, OCP, or SCP event.
13 GND power_in Ground connection to the system ground plane.
14 HGATE output Gate-drive output for the load-disconnect HSFET; connects to the gate of the external MOSFET (Q2).
15 OUT input Connection to the output power rail (external MOSFET source) used to sense the output voltage for load-disconnect control.
16 SLEEP_OV input Sleep-mode overvoltage protection pin; connect to VS for OV cutoff behavior or to OUT for OV clamp behavior during sleep mode.
17 NC unconnected No internal connection.
18 ISCP input Short-circuit detection threshold set pin; leave floating if short-circuit protection is not needed, or tie to CS+ to set the internal fixed 20 mV threshold.
19 CS- input Negative input of the current-sense amplifier.
20 CS+ input Positive input of the current-sense amplifier; connect a 50 to 100 mΩ resistor between CS+ and the external current-sense resistor.
21 NC unconnected No internal connection.
22 VS power_in IC input power supply; connect VS to the mid-point of the common-drain back-to-back MOSFET configuration and place a 100 nF capacitor between VS and GND.
23 CAP output Charge-pump output; place a 100 nF capacitor between CAP and VS to supply the gate-drive charge pump.
24 C input Cathode of the ideal diode; connects to the drain of the external MOSFET (Q1).
25 RTN unconnected Exposed thermal pad; keep it floating and do not connect it to the GND plane.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-24-EP(4x4)
Category Power Management (PMIC)
Pins 25

CAD (KiCad official)

  • Symbol: LM74910QRGERQ1
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lm74910qrgerq1-etched.step / lm74910qrgerq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm74910qrgerq1.step / lm74910qrgerq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (50 pp, sha256 0dec8e92d6d855bd, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF