component
F280025PTQR
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-48(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
F280025PTQR
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-48(7x7)
F280025PTQR from Texas Instruments, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with alternates including SCIA_TX, EPWM7_B, EQEP1_B and I2CB_SCL; ERRORSTS needs an external pull-down when used. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with alternates including SCIA_RX, EPWM7_A, EQEP1_A and I2CB_SDA; ERRORSTS needs an external pull-down when used. |
| 3 | XRSn | bidirectional | Open-drain device reset input and watchdog reset output with internal pull-up; a 2.2 kΩ to 10 kΩ resistor to VDDIO and a capacitor of 100 nF or less to VSS are recommended. |
| 4 | A6,C6 | input | Shared analog input for ADC-A channel 6 and ADC-C channel 6 (CMPSS-1/CMPSS-3 inputs); the input must stay below VDDA + 0.3 V. |
| 5 | A3/C5/VDAC | input | ADC-A channel 3 and ADC-C channel 5 analog input, and optional external reference for the on-chip CMPSS DAC; at least 1 µF capacitor required on this pin if used as DAC reference. |
| 6 | A2/C9 | input | ADC-A channel 2 and ADC-C channel 9 analog input (also a CMPSS-1 comparator input); the input must stay below VDDA + 0.3 V. |
| 7 | A15/C7 | input | ADC-A channel 15 and ADC-C channel 7 analog input (also CMPSS-1 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 8 | A11/C0 | input | ADC-A channel 11 and ADC-C channel 0 analog input (also CMPSS-1 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 9 | A5/C2 | input | ADC-A channel 5 and ADC-C channel 2 analog input (also CMPSS-3 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 10 | A1 | input | Analog input (CMPSS-1 comparator input 4 and AIO232 digital-input option); the input must stay below VDDA + 0.3 V. |
| 11 | A0/C15 | input | ADC-A channel 0 and ADC-C channel 15 analog input (also CMPSS-3 comparator input); the input must stay below VDDA + 0.3 V. |
| 12 | VREFHI | input | ADC high reference voltage: driven externally in external-reference mode, device-driven in internal-reference mode; place at least 2.2 µF between VREFHI and VREFLO as close to the device as possible and keep below VDDA + 0.3 V. |
| 13 | VREFLO | input | ADC low reference voltage; the datasheet connects it to VSSA when not externally driven. |
| 14 | A12/C1 | input | ADC-A channel 12 and ADC-C channel 1 analog input (also CMPSS-2 and CMPSS-4 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 15 | A7/C3 | input | ADC-A channel 7 and ADC-C channel 3 analog input (also CMPSS-4 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 16 | A8/C11 | input | ADC-A channel 8 and ADC-C channel 11 analog input (also CMPSS-2 and CMPSS-4 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 17 | VSSA | power_in | Analog ground for the ADC, CMPSS and other analog modules. |
| 18 | VDDA | power_in | 3.3 V analog supply; a decoupling capacitor of at least 2.2 µF is required on this pin. |
| 19 | A4/C14 | input | ADC-A channel 4 and ADC-C channel 14 analog input (also CMPSS-2 and CMPSS-4 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 20 | A9/C8 | input | ADC-A channel 9 and ADC-C channel 8 analog input (also CMPSS-2 and CMPSS-4 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 21 | A10/C10 | input | ADC-A channel 10 and ADC-C channel 10 analog input (also CMPSS-2 comparator inputs); the input must stay below VDDA + 0.3 V. |
| 22 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 23 | GPIO13 | bidirectional | General-purpose I/O 13 with alternates including EPWM7_B, EQEP1_INDEX, PMBUSA_ALERT (open-drain), FSIRXA_CLK, LINB_RX and CANA_TX. |
| 24 | GPIO12 | bidirectional | General-purpose I/O 12 with alternates including EPWM7_A, EQEP1_STROBE, PMBUSA_CTL, FSIRXA_D0, LINB_TX, SPIA_CLK, CANA_RX and HIC_INT. |
| 25 | GPIO33 | bidirectional | General-purpose I/O 33 with alternates including I2CA_SCL (open-drain), SPIB_STE, OUTPUTXBAR4, LINA_RX, FSIRXA_CLK, CANA_RX and ADCSOCAO. |
| 26 | GPIO16 | bidirectional | General-purpose I/O 16 with alternates including SPIA_SIMO, OUTPUTXBAR7, EPWM5_A, SCIA_TX, EQEP1_STROBE, PMBUSA_SCL (open-drain) and XCLKOUT. |
| 27 | GPIO24 | bidirectional | General-purpose I/O 24 with alternates including OUTPUTXBAR1, EQEP2_A, SPIB_SIMO, SCIA_TX, PMBUSA_SCL (open-drain) and ERRORSTS, which needs an external pull-down when used. |
| 28 | TCK | input | JTAG test clock with internal pull-up. |
| 29 | GPIO37/TDO | bidirectional | Default JTAG TDO function (general-purpose I/O 37 otherwise); TDO is tri-stated when no JTAG activity occurs, so an internal pull-up should be enabled or an external pull-up added. |
| 30 | TMS | bidirectional | JTAG test mode select with internal pull-up, clocked on the rising edge of TCK; an external 2.2 kΩ pull-up to VDDIO is recommended and the device has no TRSTn pin. |
| 31 | GPIO35/TDI | bidirectional | Default JTAG TDI function (general-purpose I/O 35 otherwise); the internal pull-up is disabled by default, so enable it or add an external pull-up when used as TDI. |
| 32 | GPIO32 | bidirectional | General-purpose I/O 32 with alternates including I2CA_SDA (open-drain), SPIB_CLK, LINA_TX, FSIRXA_D0, CANA_TX, ADCSOCBO and HIC_INT. |
| 33 | GPIO18_X2 | output | Crystal oscillator output X2 when the crystal oscillator is used, otherwise general-purpose I/O 18 (SPIA_CLK, CANA_RX, EPWM6_A and others). |
| 34 | GPIO19_X1 | input | Crystal oscillator or single-ended 3.3 V clock input X1 when the oscillator is used, otherwise general-purpose I/O 19; the device initialization software must configure this pin before enabling the crystal oscillator. |
| 35 | VDDIO | power_in | 3.3 V digital I/O supply; all VDDIO pins must be connected to the same 3.3 V rail. |
| 36 | VDD | power_in | 1.2 V digital logic supply generated by the internal VREG; decoupling capacitors are required on VDD. |
| 37 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 38 | GPIO4 | bidirectional | General-purpose I/O 4 with alternates including EPWM3_A, OUTPUTXBAR3, CANA_TX, SPIB_CLK, EQEP2_STROBE, FSIRXA_CLK and HIC_NWE. |
| 39 | GPIO3 | bidirectional | General-purpose I/O 3 with alternates including EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL (open-drain), SPIA_CLK, SCIA_RX, I2CB_SCL and CANA_RX. |
| 40 | GPIO2 | bidirectional | General-purpose I/O 2 with alternates including EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA (open-drain), SPIA_SIMO, SCIA_TX, I2CB_SDA and CANA_TX. |
| 41 | GPIO1 | bidirectional | General-purpose I/O 1 with alternates including EPWM1_B, I2CA_SCL (open-drain), SPIA_SOMI, CLB_OUTPUTXBAR7, HIC_A2 and FSITXA_TDM_D1. |
| 42 | GPIO0 | bidirectional | General-purpose I/O 0 with alternates including EPWM1_A, I2CA_SDA (open-drain), SPIA_STE, FSIRXA_CLK, CLB_OUTPUTXBAR8 and HIC_BASESEL1. |
| 43 | GPIO7 | bidirectional | General-purpose I/O 7 with alternates including EPWM4_B, OUTPUTXBAR5, EQEP1_B, SPIB_SIMO, FSITXA_CLK, CLB_OUTPUTXBAR2 and HIC_A6. |
| 44 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 45 | VDD | power_in | 1.2 V digital logic supply generated by the internal VREG; decoupling capacitors are required on VDD. |
| 46 | VDDIO | power_in | 3.3 V digital I/O supply; all VDDIO pins must be connected to the same 3.3 V rail. |
| 47 | GPIO5 | bidirectional | General-purpose I/O 5 with alternates including EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE, FSITXA_D1, CLB_OUTPUTXBAR5 and HIC_A7. |
| 48 | GPIO6 | bidirectional | General-purpose I/O 6 with alternates including EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, SPIB_SOMI, FSITXA_D0 and HIC_NBE1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 VDDIO(以 VSS 为基准) | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 51 | |
| 电源电压 VDDA(以 VSSA 为基准) | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 51 | |
| 输入电压 (3.3V) | VIN | -0.3 | 4.6 | V | 51 | ||
| 输出电压 | VO | -0.3 | 4.6 | V | 51 | ||
| 输入钳位电流 - 每个引脚 | IIK | -20 | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 51 | |
| 输入钳位电流 - 所有输入总计 | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 51 | |
| 数字输出电流(每引脚) | IOUT | -20 | 20 | mA | 51 | ||
| 自然通风温度 | TA | -40 | 125 | °C | 自然通风 | 51 | |
| 工作结温 | TJ | -40 | 150 | °C | 51 | ||
| 贮存温度 | Tstg | -65 | 150 | °C | 51 | ||
| 器件电源电压 VDDIO 和 VDDA(启用内部 BOR) | VDDIO/VDDA | 3.3 | 3.63 | V | 启用内部 BOR | 52 | |
| 器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) | VDDIO/VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 52 |
| 结温 | TJ | -40 | 145 | °C | 52 | ||
| 自然通风温度 | TA | -40 | 125 | °C | 52 | ||
| VDDIO 运行期间电流消耗 | IDDIO | 35 | 72 | mA | 运行期间 | 54 | |
| VDDA 运行期间电流消耗 | IDDA | 3 | 5 | mA | 运行期间 | 54 | |
| VDDIO 空闲模式电流消耗 | IDDIO | 16 | 33 | mA | 空闲模式 | 54 | |
| VDDA 空闲模式电流消耗 | IDDA | 0.01 | 0.1 | mA | 空闲模式 | 54 | |
| VDDIO 待机模式电流消耗 | IDDIO | 8 | 22 | mA | 待机模式 | 54 | |
| VDDA 待机模式电流消耗 | IDDA | 0.01 | 0.1 | mA | 待机模式 | 54 | |
| VDDIO 停机模式电流消耗 | IDDIO | 1 | 16 | mA | 停机模式 | 54 | |
| VDDA 停机模式电流消耗 | IDDA | 0.01 | 0.1 | mA | 停机模式 | 54 | |
| VDDIO 擦除/编程周期电流消耗 | IDDIO | 72 | 106 | mA | 擦除/编程周期; CPU 从 RAM 运行; 100MHz SYSCLK | 54 | |
| VDDA 擦除/编程周期电流消耗 | IDDA | 0.1 | 2.5 | mA | 擦除/编程周期 | 54 | |
| 所有输出引脚的高电平输出阻抗 | ROH | 45 | 65 | 100 | Ω | 58 | |
| 所有输出引脚的低电平输出阻抗 | ROL | 45 | 60 | 90 | Ω | 58 | |
| 高电平输入电压 | VIH | 2 | V | 58 | |||
| 低电平输入电压 | VIL | 0.8 | V | 58 | |||
| 低电平输出电压 | VOL | 0.4 | V | IOL=IOL 最大值 | 58 | ||
| 低电平输出电压 | VOL | 0.2 | V | IOL = 100µA | 58 | ||
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | 3 | V | 58 | ||
| 内部稳压器输出 | VVREG | 1.14 | 1.2 | 1.32 | V | 58 | |
| ADC 时钟 ADCCLK(源自 PERx.SYSCLK) | ADCCLK | 5 | 50 | MHz | 111 | ||
| 比较器以输入为基准的失调电压误差 | -20 | 20 | mV | 低共模,反相输入设置为 50mV | 119 | ||
| 比较器迟滞 | 4 | 12 | 20 | LSB | 1x | 119 | |
| 比较器迟滞 | 17 | 24 | 33 | LSB | 2x | 119 | |
| 比较器迟滞 | 25 | 36 | 50 | LSB | 3x | 119 | |
| 比较器迟滞 | 30 | 48 | 67 | LSB | 4x | 119 | |
| CMPSS DAC 静态失调电压误差 | -25 | 25 | mV | 包含以比较器输入为基准的误差 | 120 | ||
| CMPSS DAC 静态增益误差 | -2 | 2 | FSR 百分比 | 包含以比较器输入为基准的误差 | 120 | ||
| CMPSS DAC 静态 DNL(更正了终点) | -1 | 4 | LSB | 120 | |||
| CMPSS DAC 静态 INL(更正了终点) | -16 | 16 | LSB | 120 | |||
| CMPSS DAC VDAC 负载 | 6 | 8 | 10 | kΩ | 当 VDAC 为基准时; 每个有源 CMPSS 模块 | 120 | |
| PMBus 有效低电平输入电压 | VIL | 0.8 | V | 145 | |||
| PMBus 有效高电平输入电压 | VIH | 2.1 | V | 145 | |||
| PMBus 低电平输出电压 | VOL | 0.4 | V | Ipullup = 4mA | 145 | ||
| PMBus 必须由输入滤波器抑制的尖峰脉冲宽度 | tSP | 0 | 50 | ns | 145 | ||
| PMBus 每个引脚上的输入漏电流 | Ii | -10 | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 145 |
CAD (KiCad official)
- Symbol:
F280025PTQR - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
f280025ptqr-etched.step/f280025ptqr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280025ptqr.step/f280025ptqr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (245 pp, sha256
0723d8e3e09e1f8b, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).