Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS54618RTER

Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)

TPS54618RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply voltage operating range is 2.95 V to 6 V.
2 VIN power_in Input supply voltage operating range is 2.95 V to 6 V.
3 GND power_in Power ground pin that must be electrically connected directly to the exposed power pad under the device.
4 GND power_in Power ground pin that must be electrically connected directly to the exposed power pad under the device.
5 AGND power_in Analog ground pin that should be electrically connected to GND close to the device.
6 VSENSE input Inverting input node of the transconductance error amplifier for feedback network connection.
7 COMP output Error amplifier output connected to output switch current comparator and frequency compensation network.
8 RT/CLK bidirectional Resistor timing input or external clock input pin for setting switching frequency from 300 kHz to 2000 kHz.
9 SS/TR bidirectional Slow-start and tracking pin where external capacitor sets output voltage rise time and can be used for supply sequencing.
10 PH output Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node.
11 PH output Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node.
12 PH output Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node.
13 BOOT input Bootstrap capacitor connection (0.1 μF ceramic X5R or X7R dielectric recommended) for high-side gate drive biasing.
14 PWRGD tri_state Open-drain power good output signal that asserts low for thermal shutdown, overcurrent, or over/undervoltage fault conditions.
15 EN input Enable input pin with internal pull-up current source; pull below 1.2 V to disable or float to enable device operation.
16 VIN power_in Input supply voltage operating range is 2.95 V to 6 V.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-16-EP(3x3)
Category Power Management (PMIC)
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage PWRGD, VIN -0.3 7 V 4
Input voltage EN, RT/CLK -0.3 4 V 4
Input voltage COMP, SS, VSENSE -0.3 3 V 4
Input voltage BOOT (printed as VPH+ 7) 7 V 4
Output voltage BOOT-PH 7 V 4
Output voltage PH -0.6 7 V 4
Output voltage PH (10-ns transient) -2 10 V 10-ns transient 4
Source current EN, RT/CLK 100 µA 4
Sink current COMP, SS 100 µA 4
Sink current PWRGD 10 mA 4
Operating junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
Input voltage VVIN 3 6 V 4
Operating junction temperature (printed under TA) TA -40 150 °C 4
Operating input voltage 2.95 6 V 5
Internal undervoltage lockout threshold, UVLO stop VIN UVLO STOP 2.28 2.5 V 5
Internal undervoltage lockout threshold, UVLO start VIN UVLO START 2.45 2.6 V 5
Shutdown supply current 5.5 15 μA EN = 0 V, 25°C, 2.95 V ≤ VIN ≤ 6 V 5
Quiescent current Iq 515 650 μA VSENSE = 0.9 V, VIN = 5 V, 25°C, RT = 400 kΩ 5
Voltage reference (VSENSE pin) 0.791 0.799 0.807 V 2.95 V ≤ VIN ≤ 6 V, –40°C <TJ < 150°C 5
High-side switch resistance 12 25 mΩ BOOT-PH = 5 V 5
High-side switch resistance 16 33 mΩ BOOT-PH = 2.95 V 5
Low-side switch resistance 13 25 mΩ VIN = 5 V 5
Low-side switch resistance 17 33 mΩ VIN = 2.95 V 5
Error amplifier source/sink -20 20 μA V(COMP) = 1 V, 100-mV overdrive 5
Current limit threshold 7.46 10.6 15.3 A VIN = 6 V, 25°C < TJ < 150°C 5
Current limit threshold 7.68 10.2 13.5 A VIN = 2.95 V, 25°C < TJ < 150°C 5
PWRGD ON-resistance 56 100 Ω 6
Output low (PWRGD) 0.2 0.3 V I(PWRGD) = 3 mA 6
Minimum VIN for valid output (PWRGD) 0.65 1.5 V V(PWRGD) < 0.5 V at 100 μA 6
Switching frequency range using RT mode 200 2000 kHz 6
Switching frequency 400 500 600 kHz Rt = 400 kΩ 6
Switching frequency range using CLK mode 300 2000 kHz 6
Minimum CLK pulse width 75 ns 6
RT/CLK high threshold 1.6 2.2 V 6
RT/CLK low threshold 0.4 0.6 V 6
Minimum ON-time 75 ns Measured at 50% points on PH, IOUT = 3 A 6
Minimum ON-time 120 ns Measured at 50% points on PH, VIN = 6 V, IOUT = 0 A 6
Minimum OFF-time 60 ns Prior to skipping off pulses, BOOT-PH = 2.95 V, IOUT = 3 A 6
Junction-to-ambient thermal resistance RθJA 44.38 °C/W 4
Junction-to-case (top) thermal resistance RθJC(top) 46.09 °C/W 4
Junction-to-board thermal resistance RθJB 15.96 °C/W 4
Junction-to-top characterization parameter ψJT 0.69 °C/W 4
Junction-to-board characterization parameter ψJB 15.91 °C/W 4
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.55 °C/W 4

CAD (KiCad official)

  • Symbol: TPS54618RTER
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: tps54618rter-etched.step / tps54618rter-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps54618rter.step / tps54618rter.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 008c22400b0f5dae, retrieved 2026-09-24, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF