Generated by kicad-footprint-generator · KiCad file format 20260206
TPS54618RTER
Texas Instruments · DC-DC Converters · WQFN-16-EP(3x3)
TPS54618RTER from Texas Instruments, in a WQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage operating range is 2.95 V to 6 V. |
| 2 | VIN | power_in | Input supply voltage operating range is 2.95 V to 6 V. |
| 3 | GND | power_in | Power ground pin that must be electrically connected directly to the exposed power pad under the device. |
| 4 | GND | power_in | Power ground pin that must be electrically connected directly to the exposed power pad under the device. |
| 5 | AGND | power_in | Analog ground pin that should be electrically connected to GND close to the device. |
| 6 | VSENSE | input | Inverting input node of the transconductance error amplifier for feedback network connection. |
| 7 | COMP | output | Error amplifier output connected to output switch current comparator and frequency compensation network. |
| 8 | RT/CLK | bidirectional | Resistor timing input or external clock input pin for setting switching frequency from 300 kHz to 2000 kHz. |
| 9 | SS/TR | bidirectional | Slow-start and tracking pin where external capacitor sets output voltage rise time and can be used for supply sequencing. |
| 10 | PH | output | Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node. |
| 11 | PH | output | Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node. |
| 12 | PH | output | Output of the high-side power MOSFET source and low-side synchronous rectifier drain forming the switching node. |
| 13 | BOOT | input | Bootstrap capacitor connection (0.1 μF ceramic X5R or X7R dielectric recommended) for high-side gate drive biasing. |
| 14 | PWRGD | tri_state | Open-drain power good output signal that asserts low for thermal shutdown, overcurrent, or over/undervoltage fault conditions. |
| 15 | EN | input | Enable input pin with internal pull-up current source; pull below 1.2 V to disable or float to enable device operation. |
| 16 | VIN | power_in | Input supply voltage operating range is 2.95 V to 6 V. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-16-EP(3x3) |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage PWRGD, VIN | -0.3 | 7 | V | 4 | |||
| Input voltage EN, RT/CLK | -0.3 | 4 | V | 4 | |||
| Input voltage COMP, SS, VSENSE | -0.3 | 3 | V | 4 | |||
| Input voltage BOOT (printed as VPH+ 7) | 7 | V | 4 | ||||
| Output voltage BOOT-PH | 7 | V | 4 | ||||
| Output voltage PH | -0.6 | 7 | V | 4 | |||
| Output voltage PH (10-ns transient) | -2 | 10 | V | 10-ns transient | 4 | ||
| Source current EN, RT/CLK | 100 | µA | 4 | ||||
| Sink current COMP, SS | 100 | µA | 4 | ||||
| Sink current PWRGD | 10 | mA | 4 | ||||
| Operating junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage | VVIN | 3 | 6 | V | 4 | ||
| Operating junction temperature (printed under TA) | TA | -40 | 150 | °C | 4 | ||
| Operating input voltage | 2.95 | 6 | V | 5 | |||
| Internal undervoltage lockout threshold, UVLO stop | VIN UVLO STOP | 2.28 | 2.5 | V | 5 | ||
| Internal undervoltage lockout threshold, UVLO start | VIN UVLO START | 2.45 | 2.6 | V | 5 | ||
| Shutdown supply current | 5.5 | 15 | μA | EN = 0 V, 25°C, 2.95 V ≤ VIN ≤ 6 V | 5 | ||
| Quiescent current | Iq | 515 | 650 | μA | VSENSE = 0.9 V, VIN = 5 V, 25°C, RT = 400 kΩ | 5 | |
| Voltage reference (VSENSE pin) | 0.791 | 0.799 | 0.807 | V | 2.95 V ≤ VIN ≤ 6 V, –40°C <TJ < 150°C | 5 | |
| High-side switch resistance | 12 | 25 | mΩ | BOOT-PH = 5 V | 5 | ||
| High-side switch resistance | 16 | 33 | mΩ | BOOT-PH = 2.95 V | 5 | ||
| Low-side switch resistance | 13 | 25 | mΩ | VIN = 5 V | 5 | ||
| Low-side switch resistance | 17 | 33 | mΩ | VIN = 2.95 V | 5 | ||
| Error amplifier source/sink | -20 | 20 | μA | V(COMP) = 1 V, 100-mV overdrive | 5 | ||
| Current limit threshold | 7.46 | 10.6 | 15.3 | A | VIN = 6 V, 25°C < TJ < 150°C | 5 | |
| Current limit threshold | 7.68 | 10.2 | 13.5 | A | VIN = 2.95 V, 25°C < TJ < 150°C | 5 | |
| PWRGD ON-resistance | 56 | 100 | Ω | 6 | |||
| Output low (PWRGD) | 0.2 | 0.3 | V | I(PWRGD) = 3 mA | 6 | ||
| Minimum VIN for valid output (PWRGD) | 0.65 | 1.5 | V | V(PWRGD) < 0.5 V at 100 μA | 6 | ||
| Switching frequency range using RT mode | 200 | 2000 | kHz | 6 | |||
| Switching frequency | 400 | 500 | 600 | kHz | Rt = 400 kΩ | 6 | |
| Switching frequency range using CLK mode | 300 | 2000 | kHz | 6 | |||
| Minimum CLK pulse width | 75 | ns | 6 | ||||
| RT/CLK high threshold | 1.6 | 2.2 | V | 6 | |||
| RT/CLK low threshold | 0.4 | 0.6 | V | 6 | |||
| Minimum ON-time | 75 | ns | Measured at 50% points on PH, IOUT = 3 A | 6 | |||
| Minimum ON-time | 120 | ns | Measured at 50% points on PH, VIN = 6 V, IOUT = 0 A | 6 | |||
| Minimum OFF-time | 60 | ns | Prior to skipping off pulses, BOOT-PH = 2.95 V, IOUT = 3 A | 6 | |||
| Junction-to-ambient thermal resistance | RθJA | 44.38 | °C/W | 4 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 46.09 | °C/W | 4 | |||
| Junction-to-board thermal resistance | RθJB | 15.96 | °C/W | 4 | |||
| Junction-to-top characterization parameter | ψJT | 0.69 | °C/W | 4 | |||
| Junction-to-board characterization parameter | ψJB | 15.91 | °C/W | 4 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.55 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
TPS54618RTER - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: WQFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
tps54618rter-etched.step/tps54618rter-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54618rter.step/tps54618rter.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
008c22400b0f5dae, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).