3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS54295PWPR
Texas Instruments · DC-DC Converters · HTSSOP-16-EP
TPS54295PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN1 | power_in | Power input (4.5V to 18V) for high-side NFET drains and supply for 5.5V linear regulator. |
| 2 | VBST1 | power_in | Bootstrap supply for high-side NFET gate drive; internal diode to VREG5, requires 0.1µF capacitor to SW1. |
| 3 | SW1 | bidirectional | Switch node for high-side and low-side NFETs; current comparator input. |
| 4 | PGND1 | power_in | Ground return for low-side MOSFET; current comparator input. |
| 5 | EN1 | input | Enable input for converter channel 1; pull high to enable operation. |
| 6 | SS1 | output | Soft-start capacitor connection; capacitor to GND sets ramp time. |
| 7 | VFB1 | input | D-CAP2 feedback input for channel 1; connect to output voltage with resistor divider. |
| 8 | GND | power_in | Signal ground; connect SSx and VFBx returns at single point. |
| 9 | VREG5 | power_out | 5.5V regulated output; requires 1µF bypass capacitor to GND, active when VIN1 applied. |
| 10 | VFB2 | input | D-CAP2 feedback input for channel 2; connect to output voltage with resistor divider. |
| 11 | SS2 | output | Soft-start capacitor connection for channel 2; capacitor to GND sets ramp time. |
| 12 | EN2 | input | Enable input for converter channel 2; pull high to enable operation. |
| 13 | PGND2 | power_in | Ground return for low-side MOSFET; current comparator input. |
| 14 | SW2 | bidirectional | Switch node for high-side and low-side NFETs; current comparator input. |
| 15 | VBST2 | power_in | Bootstrap supply for high-side NFET gate drive; internal diode to VREG5, requires 0.1µF capacitor to SW2. |
| 16 | VIN2 | power_in | Power input (4.5V to 18V) for high-side NFET drains and supply for 5.5V linear regulator. |
| 17 | Thermal Pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-16-EP |
| Category | Power Management (PMIC) |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN1, VIN2, EN1, EN2 | -0.3 | 20 | V | 5 | |||
| Input voltage VBST1, VBST2 | -0.3 | 26 | V | 5 | |||
| Input voltage VBST1, VBST2 (10-ns transient) | -0.3 | 28 | V | 10-ns transient | 5 | ||
| Input voltage VBST1 - SW1, VBST2 - SW2 | -0.3 | 6.5 | V | 5 | |||
| Input voltage VFB1, VFB2 | -0.3 | 6.5 | V | 5 | |||
| Input voltage SW1, SW2 | -2 | 20 | V | 5 | |||
| Input voltage SW1, SW2 (10-ns transient) | -3 | 22 | V | 10-ns transient | 5 | ||
| Output voltage VREG5, SS1, SS2 | -0.3 | 6.5 | V | 5 | |||
| Output voltage PGND1, PGND2 | -0.3 | 0.3 | V | 5 | |||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -55 | 150 | °C | 5 | ||
| Supply input voltage VIN1, VIN2 | 4.5 | 18 | V | 5 | |||
| Input voltage VBST1, VBST2 | -0.1 | 24 | V | 5 | |||
| Input voltage VBST1, VBST2 (10-ns transient) | -0.1 | 27 | V | 10-ns transient | 5 | ||
| Input voltage VBST1 - SW1, VBST2 - SW2 | -0.1 | 5.7 | V | 5 | |||
| Input voltage VFB1, VFB2 | -0.1 | 5.7 | V | 5 | |||
| Input voltage EN1, EN2 | -0.1 | 18 | V | 5 | |||
| Input voltage SW1, SW2 | -1 | 18 | V | 5 | |||
| Input voltage SW1, SW2 (10-ns transient) | -3 | 21 | V | 10-ns transient | 5 | ||
| Output voltage VREG5, SS1, SS2 | -0.1 | 5.7 | V | 5 | |||
| Output voltage PGND1, PGND2 | -0.1 | 0.1 | V | 5 | |||
| Output voltage | VO1, VO2 | 0.76 | 7 | V | 5 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| VINx supply current | IIN | 1300 | 2000 | µA | TA = 25°C, VEN1 = VEN2 = 5 V, VVFB1 = VVFB2 = 0.8 V | 6 | |
| VINx shutdown current | IVINSDN | 80 | 150 | µA | TA = 25°C, VEN1 = VEN2 = 0 V | 6 | |
| VFBx threshold voltage | VVFBTHLx | 758 | 765 | 773 | mV | TA = 25°C, VCH1 = 3.3 V, VCH2 = 1.5 V | 6 |
| Temperature coefficient | TCVFBx | -115 | 115 | ppm/℃ | On the basis of 25°C | 6 | |
| VFBx input current | IVFBx | -0.35 | 0.2 | 0.35 | µA | VVFBx = 0.8 V, TA = 25°C | 6 |
| ENx input resistance | RENx_IN | 225 | 450 | 900 | kΩ | VENx = 12 V | 6 |
| SSx charge current | ISSC | -8.4 | -8 | -7.6 | µA | VSSx = 0.5 V, TA = 25℃ | 6 |
| ISSC temperature coefficient (PWP) | TCISSC | -4 | 3 | nA/°C | On the basis of 25°C (PWP) | 6 | |
| SSx discharge current | ISSD | 3 | 7 | 10 | mA | VSSx = 0.5 V | 6 |
| Current limit | IOCL | 2.7 | 3.9 | 4.5 | A | LOUT = 2.2 µH (1) | 6 |
| Output OVP trip threshold | VOVP | 115 | 120 | 125 | % | measured on VFBx | 7 |
| Output UVP trip threshold | VUVP | 63 | 68 | 73 | % | measured on VFBx | 7 |
| Output UVP enable delay (UVP enable delay and soft-start time multiplier) | TUVPEN | 1.4 | 1.7 | 2 | × | UVP enable delay and soft-start time | 7 |
| Thermal resistance junction-to-ambient | RθJA | 47.5 | °C/W | PWP (HTSSOP) 16-pin | 6 | ||
| Thermal resistance junction-to-case (top) | RθJC(top) | 27.1 | °C/W | PWP (HTSSOP) 16-pin | 6 | ||
| Thermal resistance junction-to-board | RθJB | 20.8 | °C/W | PWP (HTSSOP) 16-pin | 6 | ||
| Junction-to-top characterization parameter | ψJT | 1 | °C/W | PWP (HTSSOP) 16-pin | 6 | ||
| Junction-to-board characterization parameter | ψJB | 20.6 | °C/W | PWP (HTSSOP) 16-pin | 6 | ||
| Thermal resistance junction-to-case (bottom) | RθJC(bot) | 2.7 | °C/W | PWP (HTSSOP) 16-pin | 6 |
CAD (KiCad official)
- Symbol:
TPS54295PWPR - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
tps54295pwpr-etched.step/tps54295pwpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54295pwpr.step/tps54295pwpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
7059564b942927cd, retrieved 2026-09-27, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-4-6(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).