3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗PCB Footprint
Open full view ↗Datasheet
Open in new tab ↗Contents
README
markdownSA3525SCTR
Hangzhou Silan Microelectronics · DC-DC Converters · SOP-16
SA3525SCTR from Hangzhou Silan Microelectronics, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | E/A- | input | Error amplifier inverting input. Feedback voltage-divider node for the internal error amplifier (open-loop gain ~80 dB, CMRR ~90 dB). |
| 2 | E/A+ | input | Error amplifier non-inverting input. Typically tied to the 5.1 V VREF through a divider to set the regulation setpoint. Common-mode range 1.5 V to 5.2 V. |
| 3 | /SYNC | bidirectional | Oscillator sync I/O. Active-low sync input (threshold ~2 V, input current ~1.3 mA at 3.5 V) allowing an external clock to synchronize the internal oscillator; also outputs the internal sync pulse. |
| 4 | OSCOUT | output | Oscillator clock output. Provides the internal oscillator waveform (clock amplitude ~4 V, width ~0.6 µs typ) for external timing or blanking use. |
| 5 | CT | passive | Oscillator timing capacitor connection. External CT to GND sets oscillator frequency together with RT (fOSC up to 400 kHz with CT = 470 pF, RT = 2 kΩ). |
| 6 | RT | passive | Oscillator timing resistor connection. External RT to GND sets the CT charge current and hence the oscillator frequency. |
| 7 | Discharge | output | Timing-capacitor discharge pin. Provides the CT discharge path to program the oscillator deadtime; typically connected through a resistor between CT and this pin. |
| 8 | Soft-Start | passive | Soft-start capacitor input. An external capacitor to GND is charged by the internal ~51 µA source (25-80 µA) to slowly ramp the PWM duty cycle at startup. |
| 9 | EAOUT | output | Error amplifier output / PWM comparator compensation node. Loop compensation network (R/C to E/A-) attaches here; voltage on this pin (VTH1=0.9 V to VTH2=3.2 V typ) sets the PWM duty cycle (0 to 49%). |
| 10 | /Shutdown | input | External shutdown input. Pulling this pin above VTH(SD) (~1.3 V typ) forces the outputs low and discharges the soft-start capacitor. Input current ~0.3 mA at 2.5 V. |
| 11 | AOUT | output | Push-pull PWM output A. Alternates with BOUT at half oscillator frequency; sinks/sources up to 400 mA peak (500 mA abs max). VOH ~19 V at 20 mA sourcing when VC = 20 V. |
| 12 | GND | power_in | Signal ground reference for the IC and return for all logic, oscillator, error amp, and output driver currents. |
| 13 | VC | power_in | Output-stage collector bias supply. Separate power rail (up to 40 V abs max) for the AOUT/BOUT push-pull totem drivers, allowing the gate-drive rail to differ from the VCC control-logic supply. |
| 14 | BOUT | output | Push-pull PWM output B. Complements AOUT with 180° phase offset for driving external totem-pole MOSFET or transformer-coupled gate stages; same 400 mA peak drive spec. |
| 15 | VCC | power_in | Main bias supply input. Operating range 8-35 V (40 V abs max), quiescent current ~12 mA typ (20 mA max). UVLO threshold ~8.8 V typ turns the outputs off below the lockout point. |
| 16 | VREF | power_out | 5.1 V ±1% precision reference output. Sourced up to 20 mA for external divider/bias use (50 mA abs max, short-circuit current ~80 mA); typically bypassed with 0.1 µF to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Hangzhou Silan Microelectronics |
| Package | SOP-16 |
| Category | PMIC |
| Pins | 16 |
Ordering variants
Same part, different packaging or reel option.
SA3525SCTRSA3525SCTRDC
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 输入电流 | ICC | 12 | 20 | mA | VCC = 35V | 4 | |
| 基准电源输出电压 | VREF | 5 | 5.1 | 5.2 | V | TJ = 25°C | 4 |
| 电源调整率 | ∆VREF1 | 9 | 20 | mV | VCC=8V~35V | 4 | |
| 负载调整率 | ∆VREF2 | 20 | 50 | mV | IL=0 mA ~20 mA | 4 | |
| 输出短路电流 | ISC | 80 | 100 | mA | VREF=0V,TJ = 25°C | 4 | |
| 温度稳定性 | STT | 20 | 50 | mV | 4 | ||
| 总的输出变化 | VREF | 4.95 | 5.25 | V | 4 | ||
| 长期稳定性 | ST | 20 | 50 | mV | TJ = 125°C,1000 小时 | 4 | |
| 振荡初始频率 | ACCUR | -6 | 3 | 6 | % | TJ = 25°C | 4 |
| 电压稳定性 | ∆f/∆VCC | -2 | 0.8 | 2 | % | VCC=8V~35V | 4 |
| 最大频率 | f(MAX) | 400 | 430 | kHz | RT = 2k,CT = 470pF | 4 | |
| 最小频率 | f(MIN) | 60 | 120 | Hz | RT = 200k,CT = 0.1µF | 4 | |
| 时钟幅度 | V(CLK) | 3 | 4 | V | 4 | ||
| 时钟宽度 | tW(CLK) | 0.3 | 0.6 | 1 | µs | TJ = 25°C | 4 |
| 同步信号阈值 | VTH(SYNC) | 1.2 | 2 | 2.8 | V | 4 | |
| 同步信号输入电流 | II(SYNC) | 1.3 | 2.5 | mA | Sync = 3.5V | 4 | |
| 输入失调电压 | VIO | 1.5 | 10 | mV | 4 | ||
| 输入偏置电流 | IBIAS | 1 | 10 | µA | 4 | ||
| 输入失调电流 | IIO | 0.1 | 1 | µA | 4 | ||
| 开环电压增益 | GVO | 60 | 80 | dB | RL≥10MΩ | 4 | |
| 共模抑制比 | CMRR | 60 | 90 | dB | VCM = 1.5 to 5.2V | 4 | |
| 电源纹波抑制比 | PSRR | 50 | 60 | dB | VCC = 8 to 35V | 4 | |
| 最小占空比 | D(MIN) | 0 | % | 4 | |||
| 最大占空比 | D(MAX) | 45 | 49 | % | 4 | ||
| 输入阈值电压 | VTH1 | 0.7 | 0.9 | V | 0 占空比 | 4 | |
| 输入阈值电压 | VTH2 | 3.2 | 3.6 | V | 最大占空比 | 4 | |
| 软启动输入电流 | ISOFT | 25 | 51 | 80 | µA | VSD = 0V,VSS = 0V | 4 |
| 软启动低电平 | VSL | 0.3 | 0.7 | V | VSD = 2.5V | 4 | |
| 关断阈值电压 | VTH(SD) | 0.9 | 1.3 | 1.7 | V | 4 | |
| 关断输入电流 | IN(SD) | 0.3 | 1 | mA | VSD = 2.5V | 5 | |
| 输出低电平 1 | VOL1 | 0.1 | 0.4 | V | ISINK=20mA | 5 | |
| 输出低电平 2 | VOL2 | 0.5 | 2 | V | ISINK=100mA | 5 | |
| 输出高电平 1 | VOH1 | 18 | 19 | V | ISOURCE=20mA | 5 | |
| 输出高电平 2 | VOH2 | 17 | 18 | V | ISOURCE=100mA | 5 | |
| 欠压锁定 | VUV | 6 | 8.8 | 9.2 | V | V8 and V9 = High | 5 |
| 集电极漏电流 | ILKG | 80 | 200 | µA | VCC = 35V | 5 | |
| 上升时间 | tR | 80 | 600 | ns | CL = 1nF,TJ = 25°C | 5 | |
| 下降时间 | tF | 70 | 300 | ns | CL = 1nF,TJ = 25°C | 5 | |
| ESD 人体模式 | VESD | 2 | KV | 人体模式 | 5 | ||
| 偏置电压 | VIN | 40 | V | 3 | |||
| 集电极偏置电压 | VC | 40 | V | Pin 13 | 3 | ||
| 输出电流(灌电流/拉电流) | IO | 500 | mA | Pins 11, 14 | 3 | ||
| 基准电源输出电流 | IREF | 50 | mA | Pin16 | 3 | ||
| 振荡器充电电流 | IOSC | 5 | mA | Pin 9 | 3 | ||
| 耗散功率 | PD | 1000 | mW | TA = 25°C | 3 | ||
| 工作温度 | TOPR | 0 | 70 | °C | 3 | ||
| 贮存温度 | TSTG | -65 | 150 | °C | 3 |
CAD (KiCad official)
- Symbol:
SA3525SCTR - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
sa3525sctr-etched.step/sa3525sctr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sa3525sctr.step/sa3525sctr.glbare the bare package body.
3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
sa3525sctr.step |
217 KB | You want the bare part, or you mark your own boards. |
sa3525sctr-etched.step |
2.8 MB | You want the part with SA3525SCTR already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 687 faces against 267 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Hangzhou Silan Microelectronics datasheet (8 pp, sha256
a7e088aa93d1a759, retrieved 2026-08-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).