main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs sa3525sctr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers sa3525sctr: viewers · Ray
package.json Publish 0.2.1 · Ray
page.json Publish 0.2.1 · Ray
README.md sa3525sctr: specified limits as data (metadata.characteristics, 47 rows from the datasheet) · Ray
sa3525sctr-etched.fit.json sa3525sctr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sa3525sctr-etched.glb sa3525sctr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sa3525sctr-etched.step sa3525sctr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
sa3525sctr-hero.glb sa3525sctr: hero from the plain model · Ray
sa3525sctr-hero.overlay.json sa3525sctr: hero from the plain model · Ray
sa3525sctr.glb Publish 0.1.0 · Ray
sa3525sctr.kicad_mod Publish 0.1.0 · Ray
sa3525sctr.kicad_sym Publish 0.1.0 · Ray
sa3525sctr.lbr Publish 0.1.0 · Ray
sa3525sctr.step Publish 0.1.0 · Ray

SA3525SCTR

Hangzhou Silan Microelectronics · DC-DC Converters · SOP-16

SA3525SCTR from Hangzhou Silan Microelectronics, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E/A- input Error amplifier inverting input. Feedback voltage-divider node for the internal error amplifier (open-loop gain ~80 dB, CMRR ~90 dB).
2 E/A+ input Error amplifier non-inverting input. Typically tied to the 5.1 V VREF through a divider to set the regulation setpoint. Common-mode range 1.5 V to 5.2 V.
3 /SYNC bidirectional Oscillator sync I/O. Active-low sync input (threshold ~2 V, input current ~1.3 mA at 3.5 V) allowing an external clock to synchronize the internal oscillator; also outputs the internal sync pulse.
4 OSCOUT output Oscillator clock output. Provides the internal oscillator waveform (clock amplitude ~4 V, width ~0.6 µs typ) for external timing or blanking use.
5 CT passive Oscillator timing capacitor connection. External CT to GND sets oscillator frequency together with RT (fOSC up to 400 kHz with CT = 470 pF, RT = 2 kΩ).
6 RT passive Oscillator timing resistor connection. External RT to GND sets the CT charge current and hence the oscillator frequency.
7 Discharge output Timing-capacitor discharge pin. Provides the CT discharge path to program the oscillator deadtime; typically connected through a resistor between CT and this pin.
8 Soft-Start passive Soft-start capacitor input. An external capacitor to GND is charged by the internal ~51 µA source (25-80 µA) to slowly ramp the PWM duty cycle at startup.
9 EAOUT output Error amplifier output / PWM comparator compensation node. Loop compensation network (R/C to E/A-) attaches here; voltage on this pin (VTH1=0.9 V to VTH2=3.2 V typ) sets the PWM duty cycle (0 to 49%).
10 /Shutdown input External shutdown input. Pulling this pin above VTH(SD) (~1.3 V typ) forces the outputs low and discharges the soft-start capacitor. Input current ~0.3 mA at 2.5 V.
11 AOUT output Push-pull PWM output A. Alternates with BOUT at half oscillator frequency; sinks/sources up to 400 mA peak (500 mA abs max). VOH ~19 V at 20 mA sourcing when VC = 20 V.
12 GND power_in Signal ground reference for the IC and return for all logic, oscillator, error amp, and output driver currents.
13 VC power_in Output-stage collector bias supply. Separate power rail (up to 40 V abs max) for the AOUT/BOUT push-pull totem drivers, allowing the gate-drive rail to differ from the VCC control-logic supply.
14 BOUT output Push-pull PWM output B. Complements AOUT with 180° phase offset for driving external totem-pole MOSFET or transformer-coupled gate stages; same 400 mA peak drive spec.
15 VCC power_in Main bias supply input. Operating range 8-35 V (40 V abs max), quiescent current ~12 mA typ (20 mA max). UVLO threshold ~8.8 V typ turns the outputs off below the lockout point.
16 VREF power_out 5.1 V ±1% precision reference output. Sourced up to 20 mA for external divider/bias use (50 mA abs max, short-circuit current ~80 mA); typically bypassed with 0.1 µF to GND.

Key specifications

Parameter Value
Manufacturer Hangzhou Silan Microelectronics
Package SOP-16
Category PMIC
Pins 16

Ordering variants

Same part, different packaging or reel option.

  • SA3525SCTR
  • SA3525SCTRDC

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
输入电流 ICC 12 20 mA VCC = 35V 4
基准电源输出电压 VREF 5 5.1 5.2 V TJ = 25°C 4
电源调整率 ∆VREF1 9 20 mV VCC=8V~35V 4
负载调整率 ∆VREF2 20 50 mV IL=0 mA ~20 mA 4
输出短路电流 ISC 80 100 mA VREF=0V,TJ = 25°C 4
温度稳定性 STT 20 50 mV 4
总的输出变化 VREF 4.95 5.25 V 4
长期稳定性 ST 20 50 mV TJ = 125°C,1000 小时 4
振荡初始频率 ACCUR -6 3 6 % TJ = 25°C 4
电压稳定性 ∆f/∆VCC -2 0.8 2 % VCC=8V~35V 4
最大频率 f(MAX) 400 430 kHz RT = 2k,CT = 470pF 4
最小频率 f(MIN) 60 120 Hz RT = 200k,CT = 0.1µF 4
时钟幅度 V(CLK) 3 4 V 4
时钟宽度 tW(CLK) 0.3 0.6 1 µs TJ = 25°C 4
同步信号阈值 VTH(SYNC) 1.2 2 2.8 V 4
同步信号输入电流 II(SYNC) 1.3 2.5 mA Sync = 3.5V 4
输入失调电压 VIO 1.5 10 mV 4
输入偏置电流 IBIAS 1 10 µA 4
输入失调电流 IIO 0.1 1 µA 4
开环电压增益 GVO 60 80 dB RL≥10MΩ 4
共模抑制比 CMRR 60 90 dB VCM = 1.5 to 5.2V 4
电源纹波抑制比 PSRR 50 60 dB VCC = 8 to 35V 4
最小占空比 D(MIN) 0 % 4
最大占空比 D(MAX) 45 49 % 4
输入阈值电压 VTH1 0.7 0.9 V 0 占空比 4
输入阈值电压 VTH2 3.2 3.6 V 最大占空比 4
软启动输入电流 ISOFT 25 51 80 µA VSD = 0V,VSS = 0V 4
软启动低电平 VSL 0.3 0.7 V VSD = 2.5V 4
关断阈值电压 VTH(SD) 0.9 1.3 1.7 V 4
关断输入电流 IN(SD) 0.3 1 mA VSD = 2.5V 5
输出低电平 1 VOL1 0.1 0.4 V ISINK=20mA 5
输出低电平 2 VOL2 0.5 2 V ISINK=100mA 5
输出高电平 1 VOH1 18 19 V ISOURCE=20mA 5
输出高电平 2 VOH2 17 18 V ISOURCE=100mA 5
欠压锁定 VUV 6 8.8 9.2 V V8 and V9 = High 5
集电极漏电流 ILKG 80 200 µA VCC = 35V 5
上升时间 tR 80 600 ns CL = 1nF,TJ = 25°C 5
下降时间 tF 70 300 ns CL = 1nF,TJ = 25°C 5
ESD 人体模式 VESD 2 KV 人体模式 5
偏置电压 VIN 40 V 3
集电极偏置电压 VC 40 V Pin 13 3
输出电流(灌电流/拉电流) IO 500 mA Pins 11, 14 3
基准电源输出电流 IREF 50 mA Pin16 3
振荡器充电电流 IOSC 5 mA Pin 9 3
耗散功率 PD 1000 mW TA = 25°C 3
工作温度 TOPR 0 70 °C 3
贮存温度 TSTG -65 150 °C 3

CAD (KiCad official)

  • Symbol: SA3525SCTR
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOP-16 (KiCad packages3D, STEP)
  • 3D model files: sa3525sctr-etched.step / sa3525sctr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sa3525sctr.step / sa3525sctr.glb are the bare package body.

3D model downloads

Two STEP files. Same geometry, different body top:

File Size Use it when
sa3525sctr.step 217 KB You want the bare part, or you mark your own boards.
sa3525sctr-etched.step 2.8 MB You want the part with SA3525SCTR already on it.

The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 687 faces against 267 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Hangzhou Silan Microelectronics datasheet (8 pp, sha256 a7e088aa93d1a759, retrieved 2026-08-17, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF