Generated by kicad-footprint-generator · KiCad file format 20260206
UCC3818N
Texas Instruments · AC-DC Controllers & Regulators · PDIP-16
UCC3818N from Texas Instruments, in a PDIP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground reference for all voltages; VCC and VREF should be bypassed directly to GND with a 0.1-µF or larger ceramic capacitor. |
| 2 | PKLMT | input | PFC peak current limit with a 0 V threshold, reached when PKLMT falls below 0 V, set by a level-shift divider from the current sense resistor to VREF. |
| 3 | CAOUT | output | Output of the wide-bandwidth current amplifier that commands the PFC PWM duty cycle, with compensation components placed between CAOUT and MOUT. |
| 4 | CAI | input | Noninverting input of the current amplifier, connected through a resistor to the GND side of the current sense resistor, and remains functional down to and below GND. |
| 5 | MOUT | bidirectional | Multiplier output and current amplifier inverting input, with the multiplier output current limited to 2 × IIAC. |
| 6 | IAC | input | Input to the analog multiplier carrying a current proportional to instantaneous line voltage, with a recommended maximum of 500 µA. |
| 7 | VAOUT | output | Voltage amplifier output that regulates output voltage, internally limited to approximately 5.5 V to prevent overshoot. |
| 8 | VFF | input | Feed-forward voltage generated by mirroring 1/2 of IIAC into an external single-pole filter, which should be 1.4 V at low line. |
| 9 | VREF | power_in | Output of the accurate 7.5-V reference, capable of delivering 20 mA, internally short-circuit current limited, and disabled at 0 V when VCC is below UVLO. |
| 10 | OVP/EN | input | Window comparator input that disables the output driver if the boost output is a programmed level above nominal, and disables the driver and resets SS if pulled below 1.9 V (typ). |
| 11 | VSENSE | input | Voltage amplifier inverting input, normally connected to the compensation network and to the boost output through a divider network. |
| 12 | RT | input | Oscillator charging-current program pin; a resistor between 10 kΩ and 100 kΩ to GND is recommended, with a nominal pin voltage of 3 V. |
| 13 | SS | input | Soft-start pin that charges an external capacitor with a current source to slowly increase PWM duty cycle during start-up, and is discharged when VCC is low. |
| 14 | CT | input | Oscillator timing capacitor to GND setting the PWM frequency per f ≈ 0.6/(RT × CT), with its lead kept as short and direct as possible. |
| 15 | VCC | power_in | Positive supply to be held between 10 V and 17 V for normal operation with at least 20 mA available, with an 18 V absolute maximum rating. |
| 16 | DRVOUT | output | Totem-pole MOSFET gate drive output for the boost switch, which requires a series gate resistor to limit overshoot when driving a capacitive load. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 18 | V | 4 | |||
| Supply current | ICC | 20 | mA | 4 | |||
| Gate drive current, continuous | 0.2 | A | 4 | ||||
| Gate drive current | 1.2 | A | 4 | ||||
| Input voltage, CAI, MOUT, SS | 8 | V | 4 | ||||
| Input voltage, PKLMT | 5 | V | 4 | ||||
| Input voltage, VSENSE, OVP/EN | 10 | V | 4 | ||||
| Input current, RT, IAC, PKLMT | 10 | mA | 4 | ||||
| Input current, VCC (no switching) | 20 | mA | 4 | ||||
| Maximum negative voltage, DRVOUT, PKLMT, MOUT | -0.5 | V | 4 | ||||
| Power dissipation | 1 | W | 4 | ||||
| Junction temperature | TJ | -55 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VCC input voltage | VCC | 12 | V | 5 | |||
| VSENSE input sense voltage | VSENSE | 7.5 | 10 | V | 5 | ||
| Input current for oscillator | 1.36 | 10 | mA | 5 | |||
| Junction-to-ambient thermal resistance | RθJA | 49.3 | °C/W | PDIP (N), 16 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 38.9 | °C/W | PDIP (N), 16 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 29.4 | °C/W | PDIP (N), 16 pins | 5 | ||
| Supply current, off | 150 | 300 | µA | VCC = (VCC turn-on threshold −0.3 V) | 5 | ||
| Supply current, on | 2 | 4 | 6 | mA | VCC = 12 V, No load on DRVOUT | 5 | |
| VCC turn-on threshold (UCCx818) | 9.7 | 10.2 | 10.8 | V | 5 | ||
| VCC turn-off threshold (UCCx818) | 9.4 | 9.7 | V | 5 | |||
| UVLO hysteresis (UCCx818) | 0.3 | 0.5 | V | 5 | |||
| VSENSE bias current | 50 | 200 | nA | VSENSE = VREF, VAOUT = 2.5 V | 6 | ||
| Open loop gain (voltage amplifier) | 50 | 90 | dB | VAOUT = 2 V to 5 V | 6 | ||
| High-level output voltage (VAOUT) | 5.3 | 5.5 | 5.6 | V | IL = −150 μA | 6 | |
| Low-level output voltage (VAOUT) | 0 | 50 | 150 | mV | IL = 150 μA | 6 | |
| Over voltage reference | 0.48 | 0.5 | 0.52 | V | Printed as VREF + value; offset above VREF | 6 | |
| Overvoltage hysteresis | 300 | 500 | 600 | mV | 6 | ||
| Enable threshold | 1.7 | 1.9 | 2.1 | V | 6 | ||
| Current amplifier input offset voltage | -3.5 | 0 | 2.5 | mV | VCM = 0 V, VCAOUT = 3 V | 6 | |
| Current amplifier input bias current | -50 | -100 | nA | VCM = 0 V, VCAOUT = 3 V | 6 | ||
| Common-mode rejection ratio | 60 | 80 | dB | VCM = 0 V to 1.5 V, VCAOUT = 3 V | 6 | ||
| Current amplifier high-level output voltage | 5.6 | 6.5 | 6.8 | V | IL = −120 μA | 6 | |
| Current amplifier low-level output voltage | 0.1 | 0.2 | 0.5 | V | IL = 1 mA | 6 | |
| Voltage reference input voltage | VREF | 7.387 | 7.5 | 7.613 | V | TA = 0°C to 70°C | 6 |
| Short-circuit current | -20 | -25 | -50 | mA | VREF = 0 V | 6 | |
| Oscillator initial accuracy | 85 | 100 | 115 | kHz | TA = 25°C | 6 | |
| Voltage stability | -1 | 1 | % | VCC = 10.8 V to 15 V | 6 | ||
| Total variation | 80 | 120 | kHz | Line, temp | 6 | ||
| PKLMT reference voltage | -15 | 15 | mV | 6 | |||
| PKLMT propagation delay | 150 | 350 | 500 | ns | 6 | ||
| IMOUT, high line, low power output current (0°C to 85°C) | IMOUT | 0 | -6 | -20 | µA | IAC = 500 μA, VFF = 4.7 V, VAOUT = 1.25 V | 6 |
| IMOUT, high line, high power output current | IMOUT | -70 | -90 | -105 | µA | IAC = 500 μA, VFF = 4.7 V, VAOUT = 5 V | 6 |
| IMOUT, low line, low power output current | IMOUT | -10 | -19 | -50 | µA | IAC = 150 μA, VFF = 1.4 V, VAOUT = 1.25 V | 7 |
| IMOUT, low line, high power output current | IMOUT | -268 | -300 | -345 | µA | IAC = 150 μA, VFF = 1.4 V, VAOUT = 5 V | 7 |
| IMOUT, IAC limited output current | IMOUT | -250 | -300 | -400 | µA | IAC = 150 μA, VFF = 1.3 V, VAOUT = 5 V | 7 |
| Gain constant (K) | K | 0.5 | 1 | 1.5 | 1/V | IAC = 300 μA, VFF = 3 V, VAOUT = 2.5 V | 7 |
| IMOUT, zero current | IMOUT | 0 | -2 | µA | IAC = 150 μA, VFF = 1.4 V, VAOUT = 0.25 V | 7 | |
| IMOUT, zero current, (0°C to 85°C) | IMOUT | 0 | -3 | µA | IAC = 500 μA, VFF = 4.7 V, VAOUT = 0.5 V | 7 | |
| Power limit (IMOUT x VFF) | -375 | -420 | -485 | µW | IAC = 150 μA, VFF = 1.4 V, VAOUT = 5 V | 7 | |
| VFF output current | -140 | -150 | -160 | µA | IAC = 300 μA | 7 | |
| SS charge current | -6 | -10 | -16 | µA | 7 | ||
| Pullup resistance | 5 | 12 | Ω | IO = −100 mA to −200 mA | 7 | ||
| Pulldown resistance | 2 | 10 | Ω | IO = 100 mA | 7 | ||
| Output rise time | 25 | 50 | ns | CL = 1 nF, RL = 10 Ω, VDRVOUT = 0.7 V to 9.0 V | 7 | ||
| Output fall time | 10 | 50 | ns | CL = 1 nF, RL = 10 Ω, VDRVOUT = 9.0 V to 0.7 V | 7 | ||
| Maximum duty cycle | 93 | 95 | 99 | % | 7 | ||
| Zero power comparator threshold | 0.2 | 0.33 | 0.5 | V | Measured on VAOUT | 7 |
CAD (KiCad official)
- Symbol:
UCC3818N - Footprint:
Package_DIP:DIP-16_W7.62mm - 3D model: PDIP-16 (KiCad packages3D, STEP)
- 3D model files:
ucc3818n-etched.step/ucc3818n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc3818n.step/ucc3818n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (46 pp, sha256
ca94b4ec262a1f44, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).