main
History Download
Ray Publish 0.1.0 5225d60

UCC3818N

Texas Instruments · AC-DC Controllers & Regulators · PDIP-16

UCC3818N from Texas Instruments, in a PDIP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground reference for all voltages; VCC and VREF should be bypassed directly to GND with a 0.1-µF or larger ceramic capacitor.
2 PKLMT input PFC peak current limit with a 0 V threshold, reached when PKLMT falls below 0 V, set by a level-shift divider from the current sense resistor to VREF.
3 CAOUT output Output of the wide-bandwidth current amplifier that commands the PFC PWM duty cycle, with compensation components placed between CAOUT and MOUT.
4 CAI input Noninverting input of the current amplifier, connected through a resistor to the GND side of the current sense resistor, and remains functional down to and below GND.
5 MOUT bidirectional Multiplier output and current amplifier inverting input, with the multiplier output current limited to 2 × IIAC.
6 IAC input Input to the analog multiplier carrying a current proportional to instantaneous line voltage, with a recommended maximum of 500 µA.
7 VAOUT output Voltage amplifier output that regulates output voltage, internally limited to approximately 5.5 V to prevent overshoot.
8 VFF input Feed-forward voltage generated by mirroring 1/2 of IIAC into an external single-pole filter, which should be 1.4 V at low line.
9 VREF power_in Output of the accurate 7.5-V reference, capable of delivering 20 mA, internally short-circuit current limited, and disabled at 0 V when VCC is below UVLO.
10 OVP/EN input Window comparator input that disables the output driver if the boost output is a programmed level above nominal, and disables the driver and resets SS if pulled below 1.9 V (typ).
11 VSENSE input Voltage amplifier inverting input, normally connected to the compensation network and to the boost output through a divider network.
12 RT input Oscillator charging-current program pin; a resistor between 10 kΩ and 100 kΩ to GND is recommended, with a nominal pin voltage of 3 V.
13 SS input Soft-start pin that charges an external capacitor with a current source to slowly increase PWM duty cycle during start-up, and is discharged when VCC is low.
14 CT input Oscillator timing capacitor to GND setting the PWM frequency per f ≈ 0.6/(RT × CT), with its lead kept as short and direct as possible.
15 VCC power_in Positive supply to be held between 10 V and 17 V for normal operation with at least 20 mA available, with an 18 V absolute maximum rating.
16 DRVOUT output Totem-pole MOSFET gate drive output for the boost switch, which requires a series gate resistor to limit overshoot when driving a capacitive load.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package PDIP-16
Category Power Supply Chip
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 18 V 4
Supply current ICC 20 mA 4
Gate drive current, continuous 0.2 A 4
Gate drive current 1.2 A 4
Input voltage, CAI, MOUT, SS 8 V 4
Input voltage, PKLMT 5 V 4
Input voltage, VSENSE, OVP/EN 10 V 4
Input current, RT, IAC, PKLMT 10 mA 4
Input current, VCC (no switching) 20 mA 4
Maximum negative voltage, DRVOUT, PKLMT, MOUT -0.5 V 4
Power dissipation 1 W 4
Junction temperature TJ -55 150 °C 4
Storage temperature Tstg -65 150 °C 4
VCC input voltage VCC 12 V 5
VSENSE input sense voltage VSENSE 7.5 10 V 5
Input current for oscillator 1.36 10 mA 5
Junction-to-ambient thermal resistance RθJA 49.3 °C/W PDIP (N), 16 pins 5
Junction-to-case (top) thermal resistance RθJC(top) 38.9 °C/W PDIP (N), 16 pins 5
Junction-to-board thermal resistance RθJB 29.4 °C/W PDIP (N), 16 pins 5
Supply current, off 150 300 µA VCC = (VCC turn-on threshold −0.3 V) 5
Supply current, on 2 4 6 mA VCC = 12 V, No load on DRVOUT 5
VCC turn-on threshold (UCCx818) 9.7 10.2 10.8 V 5
VCC turn-off threshold (UCCx818) 9.4 9.7 V 5
UVLO hysteresis (UCCx818) 0.3 0.5 V 5
VSENSE bias current 50 200 nA VSENSE = VREF, VAOUT = 2.5 V 6
Open loop gain (voltage amplifier) 50 90 dB VAOUT = 2 V to 5 V 6
High-level output voltage (VAOUT) 5.3 5.5 5.6 V IL = −150 μA 6
Low-level output voltage (VAOUT) 0 50 150 mV IL = 150 μA 6
Over voltage reference 0.48 0.5 0.52 V Printed as VREF + value; offset above VREF 6
Overvoltage hysteresis 300 500 600 mV 6
Enable threshold 1.7 1.9 2.1 V 6
Current amplifier input offset voltage -3.5 0 2.5 mV VCM = 0 V, VCAOUT = 3 V 6
Current amplifier input bias current -50 -100 nA VCM = 0 V, VCAOUT = 3 V 6
Common-mode rejection ratio 60 80 dB VCM = 0 V to 1.5 V, VCAOUT = 3 V 6
Current amplifier high-level output voltage 5.6 6.5 6.8 V IL = −120 μA 6
Current amplifier low-level output voltage 0.1 0.2 0.5 V IL = 1 mA 6
Voltage reference input voltage VREF 7.387 7.5 7.613 V TA = 0°C to 70°C 6
Short-circuit current -20 -25 -50 mA VREF = 0 V 6
Oscillator initial accuracy 85 100 115 kHz TA = 25°C 6
Voltage stability -1 1 % VCC = 10.8 V to 15 V 6
Total variation 80 120 kHz Line, temp 6
PKLMT reference voltage -15 15 mV 6
PKLMT propagation delay 150 350 500 ns 6
IMOUT, high line, low power output current (0°C to 85°C) IMOUT 0 -6 -20 µA IAC = 500 μA, VFF = 4.7 V, VAOUT = 1.25 V 6
IMOUT, high line, high power output current IMOUT -70 -90 -105 µA IAC = 500 μA, VFF = 4.7 V, VAOUT = 5 V 6
IMOUT, low line, low power output current IMOUT -10 -19 -50 µA IAC = 150 μA, VFF = 1.4 V, VAOUT = 1.25 V 7
IMOUT, low line, high power output current IMOUT -268 -300 -345 µA IAC = 150 μA, VFF = 1.4 V, VAOUT = 5 V 7
IMOUT, IAC limited output current IMOUT -250 -300 -400 µA IAC = 150 μA, VFF = 1.3 V, VAOUT = 5 V 7
Gain constant (K) K 0.5 1 1.5 1/V IAC = 300 μA, VFF = 3 V, VAOUT = 2.5 V 7
IMOUT, zero current IMOUT 0 -2 µA IAC = 150 μA, VFF = 1.4 V, VAOUT = 0.25 V 7
IMOUT, zero current, (0°C to 85°C) IMOUT 0 -3 µA IAC = 500 μA, VFF = 4.7 V, VAOUT = 0.5 V 7
Power limit (IMOUT x VFF) -375 -420 -485 µW IAC = 150 μA, VFF = 1.4 V, VAOUT = 5 V 7
VFF output current -140 -150 -160 µA IAC = 300 μA 7
SS charge current -6 -10 -16 µA 7
Pullup resistance 5 12 Ω IO = −100 mA to −200 mA 7
Pulldown resistance 2 10 Ω IO = 100 mA 7
Output rise time 25 50 ns CL = 1 nF, RL = 10 Ω, VDRVOUT = 0.7 V to 9.0 V 7
Output fall time 10 50 ns CL = 1 nF, RL = 10 Ω, VDRVOUT = 9.0 V to 0.7 V 7
Maximum duty cycle 93 95 99 % 7
Zero power comparator threshold 0.2 0.33 0.5 V Measured on VAOUT 7

CAD (KiCad official)

  • Symbol: UCC3818N
  • Footprint: Package_DIP:DIP-16_W7.62mm
  • 3D model: PDIP-16 (KiCad packages3D, STEP)
  • 3D model files: ucc3818n-etched.step / ucc3818n-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc3818n.step / ucc3818n.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (46 pp, sha256 ca94b4ec262a1f44, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF