main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs ucc2897apwr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers ucc2897apwr: viewers · Ray
package.json ucc2897apwr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json ucc2897apwr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/ucc2897apwr · Ray
ucc2897apwr-etched.fit.json ucc2897apwr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc2897apwr-etched.glb ucc2897apwr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc2897apwr-etched.step ucc2897apwr: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
ucc2897apwr.glb Publish 0.1.0 · Ray
ucc2897apwr.kicad_mod Publish 0.1.0 · Ray
ucc2897apwr.kicad_sym Publish 0.1.0 · Ray
ucc2897apwr.lbr Publish 0.1.0 · Ray
ucc2897apwr.step Publish 0.1.0 · Ray

UCC2897APWR

Texas Instruments · AC-DC Controllers And Regulators · TSSOP-20

UCC2897APWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Connect to input-power rail (maximum 120 V) to provide high-voltage JFET start-up current until bootstrap bias becomes available.
2 N/C unconnected No internal connection; leave floating.
3 RDEL input Program turn-on delay for gate-drive outputs via resistor to GND; delay time follows equation tDEL = 11.1×10⁻¹² × RDEL + 15×10⁻⁹ seconds.
4 RON input Program internal timing-capacitor charge current via resistor to GND; determines on-time and switching frequency along with ROFF.
5 ROFF input Program internal timing-capacitor discharge current via resistor to GND; determines off-time and maximum duty cycle along with RON.
6 VREF power_out 5-V regulated reference voltage output (up to 5 mA); bypass to GND with 0.1-µF capacitor for stability and noise filtering.
7 SYNC bidirectional Bidirectional synchronization input/output; accepts external clock synchronization signal or outputs internal oscillator timing reference when standalone.
8 GND power_in Analog ground reference for control circuitry; connect directly to PGND via single short trace to minimize control noise coupling.
9 CS input Peak current-sense input for current-mode control and cycle-by-cycle current limiting at 0.5-V threshold; requires RC filter between current-sense resistor and pin.
10 RSLOPE input Program slope-compensation current amplitude via resistor to GND; compensation slope is proportional to internal timing-capacitor waveform during OUT high periods.
11 FB input Error signal feedback from external optocoupler or error amplifier with control range 2.5 V (minimum duty) to 4.5 V (maximum duty).
12 SS/SD input Soft-start and shutdown capacitor pin; charged from 2.5 V to 4.5 V by internal current source during soft-start and discharged to 0.5 V for shutdown.
13 PGND power_in Power ground current return for high-current drivers OUT and AUX; must connect to GND pin with single short trace.
14 AUX output Gate driver output for auxiliary P-channel clamp MOSFET (active-low logic) with 2-A source and 2-A sink current capability.
15 OUT output Gate driver output for main N-channel MOSFET (active-high logic) with 2-A source and 2-A sink current capability; connect 10-kΩ resistor to PGND.
16 PVDD power_in Supply for output drivers; bypass to PGND with 10-µF capacitor at device.
17 VDD power_in Primary power supply (8.5 V to 16 V) for gate drivers and 5-V bias regulator; bypass to PGND with 1-µF capacitor at device.
18 LINEUV input Line undervoltage monitor input (1.27-V threshold, programmable hysteresis) for bulk voltage monitoring via external resistor divider.
19 LINEOV input Line overvoltage monitor input (1.27-V threshold, programmable hysteresis) that disables outputs immediately upon threshold crossing.
20 N/C unconnected No internal connection; leave floating.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSSOP-20
Category Power Management (PMIC)
Pins 20

CAD (KiCad official)

  • Symbol: UCC2897APWR
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: ucc2897apwr-etched.step / ucc2897apwr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc2897apwr.step / ucc2897apwr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (50 pp, sha256 fb294981fe94b45c, retrieved 2026-09-23, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF