Generated by kicad-footprint-generator · KiCad file format 20260206
UCC28782CDRTWR
Texas Instruments · IC · WQFN-24(4x4)
UCC28782CDRTWR from Texas Instruments, in a WQFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FLT | input | Fault input that trips if pulled above 4.5 V or below 0.5 V, with a 50-µA source for an NTC to AGND (50-µs fault delay) or a divider for line-OVP sensing (750-µs fault delay). |
| 2 | RTZ | input | A resistor to AGND programs the adaptive delay from the high-side clamp switch turn-off to the low-side switch turn-on, and parasitic capacitance on this pin must be minimized. |
| 3 | RDM | input | A resistor to AGND programs the synthesized demagnetization time that controls the high-side switch on-time for ZVS, and parasitic capacitance on this pin must be minimized. |
| 4 | IPC | input | Intelligent power control pin with a 50-µA current source into RIPC to AGND (or to CS) that programs the light-load peak current level and can disable a PFC controller. |
| 5 | BUR | input | A resistor divider from REF to AGND sets the adaptive burst mode peak-current threshold, with a 2.7-µA pull-up in LPM and a 5-µA pull-down in AAM. |
| 6 | FB | input | Feedback current input presenting a 4.25-V output with 0 µA to 75 µA pulled out from full to zero power, with a 220-pF capacitor to REF recommended. |
| 7 | REF | power_out | 5-V reference output requiring a 0.22-µF ceramic bypass capacitor to AGND, with a limited external load current, and pulling it low shuts down PWM and initiates a VDD restart. |
| 8 | AGND | power_in | Analog ground and return of the PWMH and RUN drivers, to which all analog control signals are returned. |
| 9 | CS | input | Current-sense input coupled through a line-compensation resistor to set the peak primary current each cycle, with an OCP threshold of 1.2 V and an optional OTP function. |
| 10 | RUN | output | Output that is high in the run state and low in start-up, wait and fault states, able to bias a digital isolator and gate driver for bias power management. |
| 11 | PGND | power_in | Low-side ground return of the PWML driver, which can connect to the separate source pin of a GaN GIT, the Si FET source, or AGND for a GaN power IC with logic input. |
| 12 | PWML | output | Low-side switch gate driver output with -0.5 A/+1.9 A capability, clamped to the P13 pin voltage. |
| 13 | S13 | power_out | Switched 13-V rail from P13 through an internal 2.8-Ω switch controlled by RUN, which must exceed 10 V to start PWML switching, with a 22-nF capacitor recommended. |
| 14 | P13 | power_out | Regulated 13-V output derived from VDD that drives the depletion MOSFET gate, requiring a 1-µF ceramic capacitor to AGND and a recommended 20-V Zener to AGND. |
| 15 | PWMH | output | PWM output controlling the high-side clamp switch through an external high-voltage gate driver, clamped to the 5-V REF level. |
| 16 | SWS | input | Switch-node sensing input for ZVS auto-tuning through a depletion MOSFET and a resistor higher than 500 Ω, connected to VDD internally during start-up. |
| 17 | XCD | input | X-cap discharge input with 2-mA maximum discharge current and 6.5-V line zero-crossing threshold, redundant with pin 18 and connected to AGND if the function is unused. |
| 18 | XCD | input | X-cap discharge input with 2-mA maximum discharge current and 6.5-V line zero-crossing threshold, redundant with pin 17 and connected to AGND if the function is unused. |
| 19 | VDD | power_in | Controller bias power input and integrated boost converter output, requiring a hold-up capacitor to BGND, with 10-µF or 15-µF and at least 25-V rating recommended for wide-output designs. |
| 20 | BGND | power_in | Boost converter return pin connected to the source of the internal 30-V boost switch. |
| 21 | BSW | passive | Boost converter switch node at the drain of the internal 30-V boost switch, connected to the boost inductor and diode anode, or to BGND if the boost is unused. |
| 22 | BIN | input | Boost converter input connected to the rectified auxiliary winding voltage, rated to 30 V, or tied to BGND if the boost converter is not needed. |
| 23 | VS | power_in | Voltage-sensing input coupled to the transformer auxiliary winding through a resistor divider to monitor output and input voltages and switching edges. |
| 24 | SET | input | Configures the controller for Si FETs when pulled high to REF or for GaN FETs when pulled low to AGND. |
| 25 | EP | power_in | Thermal pad that must be connected to AGND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24(4x4) |
| Category | |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD bias supply voltage | VVDD | 14 | 34 | V | 9 | ||
| VDD capacitor | CVDD | 10 | µF | 9 | |||
| P13 bypass capacitor | CP13 | 1 | µF | 9 | |||
| REF bypass capacitor | CREF | 0.22 | µF | 9 | |||
| Operating junction temperature | TJ | -40 | 140 | °C | 9 | ||
| Absolute max VDD | VDD | 38 | V | 8 | |||
| Absolute max SWS | SWS | -6 | 38 | V | 8 | ||
| Absolute max CS | CS | -0.3 | 3.6 | V | 8 | ||
| Absolute max VS | VS | -0.75 | 7 | V | 8 | ||
| Absolute max XCD, BIN, BSW | -0.3 | 30 | V | 8 | |||
| Absolute max REF, PWMH, RUN | -0.3 | 7 | V | 8 | |||
| Absolute max P13, S13, PWML | -0.3 | 20 | V | 8 | |||
| Absolute max operating junction temperature | TJ | -40 | 150 | °C | 8 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 8 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | all pins | 9 | |
| ESD CDM | V(ESD) | -500 | 500 | V | all pins | 9 | |
| Junction-to-ambient thermal resistance | RθJA | 43.1 | °C/W | RTW WQFN 24 pins | 9 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 31.6 | °C/W | 9 | |||
| Junction-to-board thermal resistance | RθJB | 20.3 | °C/W | 9 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 5.7 | °C/W | 9 | |||
| Supply current, run state | IRUN(STOP) | 0.88 | 2.2 | 2.66 | mA | No switching | 9 |
| Supply current, run state | IRUN(SW) | 2.66 | 3 | 3.55 | mA | Switching, IVSL = 0 µA | 9 |
| Supply current, wait state | IWAIT | 452 | 580 | 695 | µA | IFB = -85 µA, VBIN = VBSW = VVDD = 20 V, sum of IBIN, IBSW, and IVDD | 9 |
| Supply current, wait state | IWAIT | 465 | 540 | 658 | µA | IFB = -85 µA, BIN and BSW pins to AGND, IVDD only | 9 |
| Supply current, start state | ISTART | 150 | 235 | 301 | µA | VVDD = VVDD(ON) - 100 mV, VVS = 0 V | 9 |
| Supply current, fault state | IFAULT | 500 | 630 | µA | fault state | 9 | |
| VDD startup current limit | IVDD(LIMIT) | 1.2 | 2 | 2.53 | mA | VVDD increasing, VSWS - VVDD = 1 V, VVDD = 16.5 V | 9 |
| VDD turnon threshold | VVDD(ON) | 16.31 | 17 | 17.91 | V | VVDD increasing | 9 |
| VDD turnoff threshold | VVDD(OFF) | 9.94 | 10.6 | 11.17 | V | VVDD decreasing | 9 |
| Offset to power cycle for long output voltage overshoot | VVDD(PCT) | 1.54 | 2.2 | 2.98 | V | Offset above VVDD(OFF), IFB = -85 µA | 10 |
| Logic reset threshold for latched fault | VVDD(RST) | 3.3 | 4.3 | 4.61 | V | Voltage that VDD must cross H-L to reset a latched-off fault condition | 10 |
| VDD regulation level in boost mode | VVDD(BOOST) | 17.6 | 18.5 | 19.4 | V | IVDD = 0 mA to 30 mA, VBIN = 9 V | 10 |
| UVLO on voltage of VBIN in boost mode | VBIN(ON) | 2.03 | 2.2 | 2.42 | V | VBIN increasing | 10 |
| UVLO hysteresis below VBIN(ON) | VBIN(OFF) | 1.13 | 1.23 | 1.33 | V | VBIN decreasing | 10 |
| Highest VBIN to enable boost mode | VBIN(EN) | 14.44 | 14.9 | 15.47 | V | VBIN decreasing | 10 |
| Hysteresis above VBIN(EN) | VBIN(DIS) | 0.12 | 0.16 | 0.18 | V | VBIN increasing | 10 |
| RDS(on) of internal boost switch | RBSW | 0.94 | 1.4 | 2.28 | Ω | 10 | |
| Peak current threshold in CPC control | IBSW(MAX) | 0.27 | 0.335 | 0.38 | A | 10 | |
| Leading edge blanking time in boost mode | tBLEB | 129 | 190 | 247 | ns | 10 | |
| Maximum switching frequency in CPC control | fBSW | 389 | 420 | 499 | kHz | VBIN = 9 V | 10 |
| Minimum off time in COT control | tBOFF(MIN) | 198 | 255 | 353 | ns | IFB = -85 µA | 10 |
| Minimum off time in COT control | tBOFF(MIN) | 2.9 | 4.35 | 5.9 | µs | IBSW = 500 mA | 10 |
| P13 voltage level including load regulation | VP13 | 12 | 12.8 | 13.6 | V | 0 mA to 60 mA out of P13, run state, VVDD = 20 V | 10 |
| Max sink current of P13 pin during startup | IP13(START) | 1.53 | 2.2 | 3.04 | mA | VP13 = 14 V | 10 |
| Current sourcing limit of P13 pin | IP13(MAX) | 103.3 | 133 | 154.5 | mA | P13 shorted to AGND, VVDD = 20 V | 10 |
| Line regulation of VP13 | VR13(LINE) | -6 | 2 | 8.7 | mV | VVDD = 15 V to 35 V | 10 |
| Over voltage fault threshold above VP13 | VP13(OV) | 1.35 | 2 | 2.54 | V | 10 | |
| Dropout resistance of P13 regulator switch | RP13 | 8.5 | 13 | 22.7 | Ω | (VVDD - VP13) / 30 mA, VVDD = 11 V, 30 mA out of P13 | 10 |
| RDS(on) of internal disconnect switch P13 to S13 | RS13 | 2.1 | 2.8 | 3.82 | Ω | (VP13 - VS13) / 30 mA, VVDD = 11 V, 30 mA out of S13 | 10 |
| S13_OK threshold to enable switching | VS13_OK | 9.63 | 10.2 | 10.7 | V | VRUN = 5 V | 10 |
| Current sourcing limit of S13 pin | IS13(MAX) | 260.7 | 350 | 452.5 | mA | S13 shorted to AGND, VVDD = 20 V | 10 |
| REF voltage level | VREF | 4.9 | 5 | 5.13 | V | IREF = 0 A | 10 |
| Current sourcing limit of REF pin | IREF(MAX) | 14.3 | 17 | 20.3 | mA | REF shorted to AGND, VVDD = 20 V | 10 |
| Line regulation of VREF | VR5(LINE) | -7 | -3 | 1 | mV | VVDD = 12 V to 35 V | 10 |
| Load regulation of VREF | VR5(LOAD) | -16 | 0.1 | 25 | mV | 0 mA to 1 mA out of REF, change in VREF | 10 |
| VS negative clamp level | VVSNC | 221 | 287 | 344 | mV | IVSL = -1.25 mA, voltage below ground | 10 |
| Zero-crossing detection level | VZCD | 12.4 | 35 | 67.2 | mV | VVS decreasing | 10 |
| VS input bias current | IVSB | -0.23 | 0 | 0.31 | µA | VVS = 4 V | 10 |
| VS threshold voltage in SM1 startup mode | VVS(SM1) | 242.4 | 282 | 318.3 | mV | 10 | |
| Thermal-shutdown temperature | TJ(STOP) | 125 | 162 | °C | Internal junction temperature | 13 | |
| OPP fault timer | tOPP | 130 | 164 | 201.1 | ms | IFB = 0 A | 13 |
| Fault reset delay timer | tFDR | 1.2 | 1.5 | 2.25 | s | OCP, OPP, OVP, SCP or CS pin fault | 13 |
| VS line-sense run current | IVSL(RUN) | 313 | 365 | 408.6 | µA | Current out of VS pin increasing | 13 |
| VS line-sense stop current | IVSL(STOP) | 255 | 305 | 336.4 | µA | Current out of VS pin decreasing | 13 |
| NTC shut-down voltage | VNTCTH | 0.47 | 0.5 | 0.52 | V | FLT voltage decreasing | 13 |
| Shut-down voltage of input OVP | VIOVPTH | 4.3 | 4.5 | 4.67 | V | FLT voltage increasing | 13 |
| Maximum programmable dead time | tZ(MAX) | 397.8 | 478 | 592.8 | ns | RRTZ = 280 kΩ, IVSL = -1 mA, VSET = 5 V | 13 |
| Minimum programmable dead time | tZ(MIN) | 56.1 | 70 | 89.1 | ns | RRTZ = 78.4 kΩ, IVSL = -1 mA, VSET = 0 V | 13 |
| SWS zero voltage threshold | VTH(SWS) | 3.7 | 4.04 | 4.4 | V | VSET = 0 V | 13 |
| Maximum control FB current | IFB(SBP) | 64.2 | 75 | 87.1 | µA | IFB increasing | 14 |
| Regulated FB voltage level | VFB(REG) | 4.02 | 4.25 | 4.53 | V | 14 | |
| XCD upper zero-crossing threshold | VXCD(UP) | 6.8 | 7.5 | 7.9 | V | 14 | |
| Maximum XCD discharge current | IXCD(MAX) | 1.65 | 2 | 2.5 | mA | VXCD = 15 V | 14 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | to minimize the regulator output switching loop area. Rather than with the BGND pin, the low-noise ground terminal of CVDD should be used to connect the BGND net to the AGND pin with a low im | 34 |
CAD (KiCad official)
- Symbol:
UCC28782CDRTWR - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
ucc28782cdrtwr-etched.step/ucc28782cdrtwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ucc28782cdrtwr.step/ucc28782cdrtwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (97 pp, sha256
44628a4d9f5dac3b, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).