Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

UCC28782CDRTWR

Texas Instruments · IC · WQFN-24(4x4)

UCC28782CDRTWR from Texas Instruments, in a WQFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FLT input Fault input that trips if pulled above 4.5 V or below 0.5 V, with a 50-µA source for an NTC to AGND (50-µs fault delay) or a divider for line-OVP sensing (750-µs fault delay).
2 RTZ input A resistor to AGND programs the adaptive delay from the high-side clamp switch turn-off to the low-side switch turn-on, and parasitic capacitance on this pin must be minimized.
3 RDM input A resistor to AGND programs the synthesized demagnetization time that controls the high-side switch on-time for ZVS, and parasitic capacitance on this pin must be minimized.
4 IPC input Intelligent power control pin with a 50-µA current source into RIPC to AGND (or to CS) that programs the light-load peak current level and can disable a PFC controller.
5 BUR input A resistor divider from REF to AGND sets the adaptive burst mode peak-current threshold, with a 2.7-µA pull-up in LPM and a 5-µA pull-down in AAM.
6 FB input Feedback current input presenting a 4.25-V output with 0 µA to 75 µA pulled out from full to zero power, with a 220-pF capacitor to REF recommended.
7 REF power_out 5-V reference output requiring a 0.22-µF ceramic bypass capacitor to AGND, with a limited external load current, and pulling it low shuts down PWM and initiates a VDD restart.
8 AGND power_in Analog ground and return of the PWMH and RUN drivers, to which all analog control signals are returned.
9 CS input Current-sense input coupled through a line-compensation resistor to set the peak primary current each cycle, with an OCP threshold of 1.2 V and an optional OTP function.
10 RUN output Output that is high in the run state and low in start-up, wait and fault states, able to bias a digital isolator and gate driver for bias power management.
11 PGND power_in Low-side ground return of the PWML driver, which can connect to the separate source pin of a GaN GIT, the Si FET source, or AGND for a GaN power IC with logic input.
12 PWML output Low-side switch gate driver output with -0.5 A/+1.9 A capability, clamped to the P13 pin voltage.
13 S13 power_out Switched 13-V rail from P13 through an internal 2.8-Ω switch controlled by RUN, which must exceed 10 V to start PWML switching, with a 22-nF capacitor recommended.
14 P13 power_out Regulated 13-V output derived from VDD that drives the depletion MOSFET gate, requiring a 1-µF ceramic capacitor to AGND and a recommended 20-V Zener to AGND.
15 PWMH output PWM output controlling the high-side clamp switch through an external high-voltage gate driver, clamped to the 5-V REF level.
16 SWS input Switch-node sensing input for ZVS auto-tuning through a depletion MOSFET and a resistor higher than 500 Ω, connected to VDD internally during start-up.
17 XCD input X-cap discharge input with 2-mA maximum discharge current and 6.5-V line zero-crossing threshold, redundant with pin 18 and connected to AGND if the function is unused.
18 XCD input X-cap discharge input with 2-mA maximum discharge current and 6.5-V line zero-crossing threshold, redundant with pin 17 and connected to AGND if the function is unused.
19 VDD power_in Controller bias power input and integrated boost converter output, requiring a hold-up capacitor to BGND, with 10-µF or 15-µF and at least 25-V rating recommended for wide-output designs.
20 BGND power_in Boost converter return pin connected to the source of the internal 30-V boost switch.
21 BSW passive Boost converter switch node at the drain of the internal 30-V boost switch, connected to the boost inductor and diode anode, or to BGND if the boost is unused.
22 BIN input Boost converter input connected to the rectified auxiliary winding voltage, rated to 30 V, or tied to BGND if the boost converter is not needed.
23 VS power_in Voltage-sensing input coupled to the transformer auxiliary winding through a resistor divider to monitor output and input voltages and switching edges.
24 SET input Configures the controller for Si FETs when pulled high to REF or for GaN FETs when pulled low to AGND.
25 EP power_in Thermal pad that must be connected to AGND.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-24(4x4)
Category
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDD bias supply voltage VVDD 14 34 V 9
VDD capacitor CVDD 10 µF 9
P13 bypass capacitor CP13 1 µF 9
REF bypass capacitor CREF 0.22 µF 9
Operating junction temperature TJ -40 140 °C 9
Absolute max VDD VDD 38 V 8
Absolute max SWS SWS -6 38 V 8
Absolute max CS CS -0.3 3.6 V 8
Absolute max VS VS -0.75 7 V 8
Absolute max XCD, BIN, BSW -0.3 30 V 8
Absolute max REF, PWMH, RUN -0.3 7 V 8
Absolute max P13, S13, PWML -0.3 20 V 8
Absolute max operating junction temperature TJ -40 150 °C 8
Storage temperature Tstg -65 150 °C 8
ESD HBM V(ESD) -2000 2000 V all pins 9
ESD CDM V(ESD) -500 500 V all pins 9
Junction-to-ambient thermal resistance RθJA 43.1 °C/W RTW WQFN 24 pins 9
Junction-to-case (top) thermal resistance RθJC(top) 31.6 °C/W 9
Junction-to-board thermal resistance RθJB 20.3 °C/W 9
Junction-to-case (bottom) thermal resistance RθJC(bot) 5.7 °C/W 9
Supply current, run state IRUN(STOP) 0.88 2.2 2.66 mA No switching 9
Supply current, run state IRUN(SW) 2.66 3 3.55 mA Switching, IVSL = 0 µA 9
Supply current, wait state IWAIT 452 580 695 µA IFB = -85 µA, VBIN = VBSW = VVDD = 20 V, sum of IBIN, IBSW, and IVDD 9
Supply current, wait state IWAIT 465 540 658 µA IFB = -85 µA, BIN and BSW pins to AGND, IVDD only 9
Supply current, start state ISTART 150 235 301 µA VVDD = VVDD(ON) - 100 mV, VVS = 0 V 9
Supply current, fault state IFAULT 500 630 µA fault state 9
VDD startup current limit IVDD(LIMIT) 1.2 2 2.53 mA VVDD increasing, VSWS - VVDD = 1 V, VVDD = 16.5 V 9
VDD turnon threshold VVDD(ON) 16.31 17 17.91 V VVDD increasing 9
VDD turnoff threshold VVDD(OFF) 9.94 10.6 11.17 V VVDD decreasing 9
Offset to power cycle for long output voltage overshoot VVDD(PCT) 1.54 2.2 2.98 V Offset above VVDD(OFF), IFB = -85 µA 10
Logic reset threshold for latched fault VVDD(RST) 3.3 4.3 4.61 V Voltage that VDD must cross H-L to reset a latched-off fault condition 10
VDD regulation level in boost mode VVDD(BOOST) 17.6 18.5 19.4 V IVDD = 0 mA to 30 mA, VBIN = 9 V 10
UVLO on voltage of VBIN in boost mode VBIN(ON) 2.03 2.2 2.42 V VBIN increasing 10
UVLO hysteresis below VBIN(ON) VBIN(OFF) 1.13 1.23 1.33 V VBIN decreasing 10
Highest VBIN to enable boost mode VBIN(EN) 14.44 14.9 15.47 V VBIN decreasing 10
Hysteresis above VBIN(EN) VBIN(DIS) 0.12 0.16 0.18 V VBIN increasing 10
RDS(on) of internal boost switch RBSW 0.94 1.4 2.28 Ω 10
Peak current threshold in CPC control IBSW(MAX) 0.27 0.335 0.38 A 10
Leading edge blanking time in boost mode tBLEB 129 190 247 ns 10
Maximum switching frequency in CPC control fBSW 389 420 499 kHz VBIN = 9 V 10
Minimum off time in COT control tBOFF(MIN) 198 255 353 ns IFB = -85 µA 10
Minimum off time in COT control tBOFF(MIN) 2.9 4.35 5.9 µs IBSW = 500 mA 10
P13 voltage level including load regulation VP13 12 12.8 13.6 V 0 mA to 60 mA out of P13, run state, VVDD = 20 V 10
Max sink current of P13 pin during startup IP13(START) 1.53 2.2 3.04 mA VP13 = 14 V 10
Current sourcing limit of P13 pin IP13(MAX) 103.3 133 154.5 mA P13 shorted to AGND, VVDD = 20 V 10
Line regulation of VP13 VR13(LINE) -6 2 8.7 mV VVDD = 15 V to 35 V 10
Over voltage fault threshold above VP13 VP13(OV) 1.35 2 2.54 V 10
Dropout resistance of P13 regulator switch RP13 8.5 13 22.7 Ω (VVDD - VP13) / 30 mA, VVDD = 11 V, 30 mA out of P13 10
RDS(on) of internal disconnect switch P13 to S13 RS13 2.1 2.8 3.82 Ω (VP13 - VS13) / 30 mA, VVDD = 11 V, 30 mA out of S13 10
S13_OK threshold to enable switching VS13_OK 9.63 10.2 10.7 V VRUN = 5 V 10
Current sourcing limit of S13 pin IS13(MAX) 260.7 350 452.5 mA S13 shorted to AGND, VVDD = 20 V 10
REF voltage level VREF 4.9 5 5.13 V IREF = 0 A 10
Current sourcing limit of REF pin IREF(MAX) 14.3 17 20.3 mA REF shorted to AGND, VVDD = 20 V 10
Line regulation of VREF VR5(LINE) -7 -3 1 mV VVDD = 12 V to 35 V 10
Load regulation of VREF VR5(LOAD) -16 0.1 25 mV 0 mA to 1 mA out of REF, change in VREF 10
VS negative clamp level VVSNC 221 287 344 mV IVSL = -1.25 mA, voltage below ground 10
Zero-crossing detection level VZCD 12.4 35 67.2 mV VVS decreasing 10
VS input bias current IVSB -0.23 0 0.31 µA VVS = 4 V 10
VS threshold voltage in SM1 startup mode VVS(SM1) 242.4 282 318.3 mV 10
Thermal-shutdown temperature TJ(STOP) 125 162 °C Internal junction temperature 13
OPP fault timer tOPP 130 164 201.1 ms IFB = 0 A 13
Fault reset delay timer tFDR 1.2 1.5 2.25 s OCP, OPP, OVP, SCP or CS pin fault 13
VS line-sense run current IVSL(RUN) 313 365 408.6 µA Current out of VS pin increasing 13
VS line-sense stop current IVSL(STOP) 255 305 336.4 µA Current out of VS pin decreasing 13
NTC shut-down voltage VNTCTH 0.47 0.5 0.52 V FLT voltage decreasing 13
Shut-down voltage of input OVP VIOVPTH 4.3 4.5 4.67 V FLT voltage increasing 13
Maximum programmable dead time tZ(MAX) 397.8 478 592.8 ns RRTZ = 280 kΩ, IVSL = -1 mA, VSET = 5 V 13
Minimum programmable dead time tZ(MIN) 56.1 70 89.1 ns RRTZ = 78.4 kΩ, IVSL = -1 mA, VSET = 0 V 13
SWS zero voltage threshold VTH(SWS) 3.7 4.04 4.4 V VSET = 0 V 13
Maximum control FB current IFB(SBP) 64.2 75 87.1 µA IFB increasing 14
Regulated FB voltage level VFB(REG) 4.02 4.25 4.53 V 14
XCD upper zero-crossing threshold VXCD(UP) 6.8 7.5 7.9 V 14
Maximum XCD discharge current IXCD(MAX) 1.65 2 2.5 mA VXCD = 15 V 14

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper to minimize the regulator output switching loop area. Rather than with the BGND pin, the low-noise ground terminal of CVDD should be used to connect the BGND net to the AGND pin with a low im 34

CAD (KiCad official)

  • Symbol: UCC28782CDRTWR
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: WQFN-24(4x4) (KiCad packages3D, STEP)
  • 3D model files: ucc28782cdrtwr-etched.step / ucc28782cdrtwr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ucc28782cdrtwr.step / ucc28782cdrtwr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (97 pp, sha256 44628a4d9f5dac3b, retrieved 2026-10-27, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF