main
History Download
Ray Initial commit: component/uc2625dwtr dedf1c5

UC2625DWTR

Texas Instruments · Brushless DC (BLDC) Motor Driver · SOIC-28-300mil

UC2625DWTR from Texas Instruments, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E/A OUT output Error amplifier output; output swing range 0.25 V to 3.50 V; pull-up current -16 to -5 μA; drives PWM comparator and may be tied to E/A IN(−) for closed-loop compensation.
2 VREF power_out Trimmed 5.0 V reference output (4.7-5.3 V over operating range); maximum advised load 30 mA; short-circuit current 50-150 mA; must be bypassed with at least 0.1 μF to GND.
3 ISENSE output Current-sense amplifier output; ISENSE = 2.5 V + 2 ×
4 ISENSE1 input Differential current-sense input 1; input range −1 V to +2 V; input bias current -850 to 0 μA to 0 V; offset current ±12 μA max; use matched filter resistors ≤2 kΩ for accuracy.
5 ISENSE2 input Differential current-sense input 2; interchangeable with ISENSE1; input range −1 V to +2 V; input bias current -850 to 0 μA; differential input may be as high as ±0.5 V before saturation.
6 DIR input Motor direction latch input; threshold 0.8-2.0 V, hysteresis 0.6 V; input current -30 to 30 μA; direction change is inhibited when SPEED-IN exceeds 250 mV to prevent unsafe reversal.
7 SPEED-IN input Speed-sense input used to gate the direction latch; threshold 220-290 mV (typ 257 mV); input current -30 to 30 μA; typically connected to TACH-OUT through an RC filter.
8 H1 input Hall-effect shaft-position sensor input 1; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range.
9 H2 input Hall-effect shaft-position sensor input 2; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range.
10 H3 input Hall-effect shaft-position sensor input 3; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range.
11 PWR VCC power_in Power supply pin for the PD totem-pole drivers; carries all current sourced by PDA, PDB, and PDC; may be current-limited with a series resistor when driving Darlington bases.
12 PDC output Low-side totem-pole driver C; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF.
13 PDB output Low-side totem-pole driver B; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF.
14 PDA output Low-side totem-pole driver A; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF.
15 GND power_in Ground reference; all internal thresholds and outputs except the PU and PD supply rails are referred to this pin.
16 PUC output High-side open-collector driver C; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA.
17 PUB output High-side open-collector driver B; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA.
18 PUA output High-side open-collector driver A; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA.
19 VCC power_in Main logic and control supply; operating range 10 V to 18 V; under-voltage lockout keeps all outputs off below 7.5 V; turn-on threshold 8.65-9.45 V; bypass with 0.1 μF ceramic.
20 TACH-OUT output Tachometer output; fires a fixed-width 5 V pulse (on-time 170-280 μs) on each H1/H2/H3 transition; high level 4.7-5.3 V into 10 kΩ; low level ≤0.2 V; average voltage is proportional to speed.
21 RC-BRAKE bidirectional RC brake timing and brake-command pin; external RT (10 kΩ-500 kΩ) and CT (1 nF-100 nF) to GND set discharge window T = 0.67 RTCT; pulling pin below 0.8-1.2 V threshold commands full-brake mode; input current -4.0 to -1.9 mA.
22 QUAD SEL input Two/four-quadrant chopping selection input; low selects two-quadrant, high selects four-quadrant; threshold 0.8-2.0 V; hysteresis 70 mV; input current -30 to 150 μA.
23 OV-COAST input Over-voltage shutdown and coast input; inhibit threshold 1.65-1.85 V; restart threshold 1.55-1.75 V; hysteresis 0.05-0.15 V; input current -10 to 0 μA; accepts TTL, 5-V CMOS, or 12-V CMOS.
24 SSTART bidirectional Soft-start pin; internal transistor discharges an external capacitor fully on undervoltage or overcurrent fault; clamps E/A OUT to SSTART voltage; restart threshold 0.1-0.3 V; discharge current 0.1-3.0 mA.
25 RC-OSC passive Oscillator RC timing pin; connect ROSC (10 kΩ-100 kΩ) to VREF and COSC (1 nF-100 nF) to GND; oscillator frequency F ≈ 2/(ROSC × COSC); ramp is ≈1.2 V peak-to-peak centered at 1.6 V; 40-60 kHz typical.
26 PWM IN input PWM comparator input; compared to E/A OUT to generate the PWM chop command; input current 0-30 μA; typically connected to the RC-OSC ramp for voltage-mode PWM control.
27 E/A IN(-) input Error amplifier inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; input offset ±10 mV; tie to E/A OUT for unity-gain buffer configuration.
28 E/A IN(+) input Error amplifier non-inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; voltage gain 70-90 dB; can be driven by ISENSE output, TACH-OUT filter, or external command voltage.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-28-300mil
Category Motor Driver ICs
Pins 28

CAD (KiCad official)

  • Symbol: UC2625DWTR
  • Footprint: Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm
  • 3D model: SOIC-28-300mil (KiCad packages3D, STEP)
  • 3D model files: uc2625dwtr-etched.step / uc2625dwtr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); uc2625dwtr.step / uc2625dwtr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (25 pp, sha256 dcf54a877fad8159, retrieved 2026-09-22, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF