← Commit history

Initial commit: component/uc2625dwtr

Ray ·dedf1c572b ·
2 files changed +325
README.mdadded+64
@@ -0,0 +1,64 @@+# UC2625DWTR++**Texas Instruments** · Brushless DC (BLDC) Motor Driver · SOIC-28-300mil++UC2625DWTR from Texas Instruments, in a SOIC-28-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | E/A OUT | output | Error amplifier output; output swing range 0.25 V to 3.50 V; pull-up current -16 to -5 μA; drives PWM comparator and may be tied to E/A IN(−) for closed-loop compensation. |+| 2 | VREF | power_out | Trimmed 5.0 V reference output (4.7-5.3 V over operating range); maximum advised load 30 mA; short-circuit current 50-150 mA; must be bypassed with at least 0.1 μF to GND. |+| 3 | ISENSE | output | Current-sense amplifier output; ISENSE = 2.5 V + 2 × |ISENSE1 − ISENSE2|; level shift 2.4-2.65 V; feeds peak-current (0.14-0.26 V) and overcurrent (0.26-0.36 V) comparators. |+| 4 | ISENSE1 | input | Differential current-sense input 1; input range −1 V to +2 V; input bias current -850 to 0 μA to 0 V; offset current ±12 μA max; use matched filter resistors ≤2 kΩ for accuracy. |+| 5 | ISENSE2 | input | Differential current-sense input 2; interchangeable with ISENSE1; input range −1 V to +2 V; input bias current -850 to 0 μA; differential input may be as high as ±0.5 V before saturation. |+| 6 | DIR | input | Motor direction latch input; threshold 0.8-2.0 V, hysteresis 0.6 V; input current -30 to 30 μA; direction change is inhibited when SPEED-IN exceeds 250 mV to prevent unsafe reversal. |+| 7 | SPEED-IN | input | Speed-sense input used to gate the direction latch; threshold 220-290 mV (typ 257 mV); input current -30 to 30 μA; typically connected to TACH-OUT through an RC filter. |+| 8 | H1 | input | Hall-effect shaft-position sensor input 1; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range. |+| 9 | H2 | input | Hall-effect shaft-position sensor input 2; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range. |+| 10 | H3 | input | Hall-effect shaft-position sensor input 3; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range. |+| 11 | PWR VCC | power_in | Power supply pin for the PD totem-pole drivers; carries all current sourced by PDA, PDB, and PDC; may be current-limited with a series resistor when driving Darlington bases. |+| 12 | PDC | output | Low-side totem-pole driver C; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF. |+| 13 | PDB | output | Low-side totem-pole driver B; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF. |+| 14 | PDA | output | Low-side totem-pole driver A; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF. |+| 15 | GND | power_in | Ground reference; all internal thresholds and outputs except the PU and PD supply rails are referred to this pin. |+| 16 | PUC | output | High-side open-collector driver C; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA. |+| 17 | PUB | output | High-side open-collector driver B; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA. |+| 18 | PUA | output | High-side open-collector driver A; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA. |+| 19 | VCC | power_in | Main logic and control supply; operating range 10 V to 18 V; under-voltage lockout keeps all outputs off below 7.5 V; turn-on threshold 8.65-9.45 V; bypass with 0.1 μF ceramic. |+| 20 | TACH-OUT | output | Tachometer output; fires a fixed-width 5 V pulse (on-time 170-280 μs) on each H1/H2/H3 transition; high level 4.7-5.3 V into 10 kΩ; low level ≤0.2 V; average voltage is proportional to speed. |+| 21 | RC-BRAKE | bidirectional | RC brake timing and brake-command pin; external RT (10 kΩ-500 kΩ) and CT (1 nF-100 nF) to GND set discharge window T = 0.67 RTCT; pulling pin below 0.8-1.2 V threshold commands full-brake mode; input current -4.0 to -1.9 mA. |+| 22 | QUAD SEL | input | Two/four-quadrant chopping selection input; low selects two-quadrant, high selects four-quadrant; threshold 0.8-2.0 V; hysteresis 70 mV; input current -30 to 150 μA. |+| 23 | OV-COAST | input | Over-voltage shutdown and coast input; inhibit threshold 1.65-1.85 V; restart threshold 1.55-1.75 V; hysteresis 0.05-0.15 V; input current -10 to 0 μA; accepts TTL, 5-V CMOS, or 12-V CMOS. |+| 24 | SSTART | bidirectional | Soft-start pin; internal transistor discharges an external capacitor fully on undervoltage or overcurrent fault; clamps E/A OUT to SSTART voltage; restart threshold 0.1-0.3 V; discharge current 0.1-3.0 mA. |+| 25 | RC-OSC | passive | Oscillator RC timing pin; connect ROSC (10 kΩ-100 kΩ) to VREF and COSC (1 nF-100 nF) to GND; oscillator frequency F ≈ 2/(ROSC × COSC); ramp is ≈1.2 V peak-to-peak centered at 1.6 V; 40-60 kHz typical. |+| 26 | PWM IN | input | PWM comparator input; compared to E/A OUT to generate the PWM chop command; input current 0-30 μA; typically connected to the RC-OSC ramp for voltage-mode PWM control. |+| 27 | E/A IN(-) | input | Error amplifier inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; input offset ±10 mV; tie to E/A OUT for unity-gain buffer configuration. |+| 28 | E/A IN(+) | input | Error amplifier non-inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; voltage gain 70-90 dB; can be driven by ISENSE output, TACH-OUT filter, or external command voltage. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-28-300mil |+| Category | Motor Driver ICs |+| Pins | 28 |++## CAD (KiCad official)++- Symbol: `UC2625DWTR`+- Footprint: `Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm`+- 3D model: SOIC-28-300mil (KiCad packages3D, STEP)+- 3D model files: `uc2625dwtr-etched.step` / `uc2625dwtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `uc2625dwtr.step` / `uc2625dwtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/uc2625) (25 pp, sha256 `dcf54a877fad8159`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/uc2625dwtr-datasheet.pdf)
page.jsonadded+261
@@ -0,0 +1,261 @@+{+  "slug": "uc2625dwtr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Brushless DC (BLDC) Motor Driver, SOIC-28-300mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "motor driver ics",+    "uc2625dwtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "uc2625dwtr.kicad_sym",+    "uc2625dwtr.kicad_mod",+    "uc2625dwtr.glb",+    "uc2625dwtr.step",+    "uc2625dwtr.lbr",+    "docs/hero.png",+    "docs/uc2625dwtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UC2625DWTR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-28-300mil",+    "pin_count": 28,+    "category": "Motor Driver ICs",+    "subcategory": "Brushless DC (BLDC) Motor Driver",+    "datasheet": "https://www.ti.com/cn/lit/gpn/uc2625",+    "parts": {+      "symbol": "uc2625dwtr.kicad_sym",+      "footprint": "uc2625dwtr.kicad_mod",+      "model_3d": "uc2625dwtr-etched.glb",+      "model_3d_plain": "uc2625dwtr.glb",+      "model_3d_step": "uc2625dwtr-etched.step",+      "model_3d_step_plain": "uc2625dwtr.step",+      "lbr": "uc2625dwtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2150731"+    },+    "pins": [+      {+        "number": "1",+        "name": "E/A OUT",+        "type": "output",+        "description": "Error amplifier output; output swing range 0.25 V to 3.50 V; pull-up current -16 to -5 μA; drives PWM comparator and may be tied to E/A IN(−) for closed-loop compensation."+      },+      {+        "number": "2",+        "name": "VREF",+        "type": "power_out",+        "description": "Trimmed 5.0 V reference output (4.7-5.3 V over operating range); maximum advised load 30 mA; short-circuit current 50-150 mA; must be bypassed with at least 0.1 μF to GND."+      },+      {+        "number": "3",+        "name": "ISENSE",+        "type": "output",+        "description": "Current-sense amplifier output; ISENSE = 2.5 V + 2 × |ISENSE1 − ISENSE2|; level shift 2.4-2.65 V; feeds peak-current (0.14-0.26 V) and overcurrent (0.26-0.36 V) comparators."+      },+      {+        "number": "4",+        "name": "ISENSE1",+        "type": "input",+        "description": "Differential current-sense input 1; input range −1 V to +2 V; input bias current -850 to 0 μA to 0 V; offset current ±12 μA max; use matched filter resistors ≤2 kΩ for accuracy."+      },+      {+        "number": "5",+        "name": "ISENSE2",+        "type": "input",+        "description": "Differential current-sense input 2; interchangeable with ISENSE1; input range −1 V to +2 V; input bias current -850 to 0 μA; differential input may be as high as ±0.5 V before saturation."+      },+      {+        "number": "6",+        "name": "DIR",+        "type": "input",+        "description": "Motor direction latch input; threshold 0.8-2.0 V, hysteresis 0.6 V; input current -30 to 30 μA; direction change is inhibited when SPEED-IN exceeds 250 mV to prevent unsafe reversal."+      },+      {+        "number": "7",+        "name": "SPEED-IN",+        "type": "input",+        "description": "Speed-sense input used to gate the direction latch; threshold 220-290 mV (typ 257 mV); input current -30 to 30 μA; typically connected to TACH-OUT through an RC filter."+      },+      {+        "number": "8",+        "name": "H1",+        "type": "input",+        "description": "Hall-effect shaft-position sensor input 1; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range."+      },+      {+        "number": "9",+        "name": "H2",+        "type": "input",+        "description": "Hall-effect shaft-position sensor input 2; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range."+      },+      {+        "number": "10",+        "name": "H3",+        "type": "input",+        "description": "Hall-effect shaft-position sensor input 3; TTL-compatible low threshold 0.8-1.2 V, high threshold 1.6-2.0 V; pull-down input current -400 to -120 μA over operating range."+      },+      {+        "number": "11",+        "name": "PWR VCC",+        "type": "power_in",+        "description": "Power supply pin for the PD totem-pole drivers; carries all current sourced by PDA, PDB, and PDC; may be current-limited with a series resistor when driving Darlington bases."+      },+      {+        "number": "12",+        "name": "PDC",+        "type": "output",+        "description": "Low-side totem-pole driver C; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF."+      },+      {+        "number": "13",+        "name": "PDB",+        "type": "output",+        "description": "Low-side totem-pole driver B; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF."+      },+      {+        "number": "14",+        "name": "PDA",+        "type": "output",+        "description": "Low-side totem-pole driver A; active high turns on a low-side device; Vol 0.36-0.8 V at 50 mA; Voh 1.75-2.2 V below VCC at 50 mA; 10%-90% rise/fall time 50 ns into 1 nF."+      },+      {+        "number": "15",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference; all internal thresholds and outputs except the PU and PD supply rails are referred to this pin."+      },+      {+        "number": "16",+        "name": "PUC",+        "type": "output",+        "description": "High-side open-collector driver C; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+      },+      {+        "number": "17",+        "name": "PUB",+        "type": "output",+        "description": "High-side open-collector driver B; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+      },+      {+        "number": "18",+        "name": "PUA",+        "type": "output",+        "description": "High-side open-collector driver A; active low commands a high-side device on; rated to 50 V; leakage ≤25 μA at 50 V; Vol 1.0-1.8 V at 50 mA; fall time 50 ns at 50 mA."+      },+      {+        "number": "19",+        "name": "VCC",+        "type": "power_in",+        "description": "Main logic and control supply; operating range 10 V to 18 V; under-voltage lockout keeps all outputs off below 7.5 V; turn-on threshold 8.65-9.45 V; bypass with 0.1 μF ceramic."+      },+      {+        "number": "20",+        "name": "TACH-OUT",+        "type": "output",+        "description": "Tachometer output; fires a fixed-width 5 V pulse (on-time 170-280 μs) on each H1/H2/H3 transition; high level 4.7-5.3 V into 10 kΩ; low level ≤0.2 V; average voltage is proportional to speed."+      },+      {+        "number": "21",+        "name": "RC-BRAKE",+        "type": "bidirectional",+        "description": "RC brake timing and brake-command pin; external RT (10 kΩ-500 kΩ) and CT (1 nF-100 nF) to GND set discharge window T = 0.67 RTCT; pulling pin below 0.8-1.2 V threshold commands full-brake mode; input current -4.0 to -1.9 mA."+      },+      {+        "number": "22",+        "name": "QUAD SEL",+        "type": "input",+        "description": "Two/four-quadrant chopping selection input; low selects two-quadrant, high selects four-quadrant; threshold 0.8-2.0 V; hysteresis 70 mV; input current -30 to 150 μA."+      },+      {+        "number": "23",+        "name": "OV-COAST",+        "type": "input",+        "description": "Over-voltage shutdown and coast input; inhibit threshold 1.65-1.85 V; restart threshold 1.55-1.75 V; hysteresis 0.05-0.15 V; input current -10 to 0 μA; accepts TTL, 5-V CMOS, or 12-V CMOS."+      },+      {+        "number": "24",+        "name": "SSTART",+        "type": "bidirectional",+        "description": "Soft-start pin; internal transistor discharges an external capacitor fully on undervoltage or overcurrent fault; clamps E/A OUT to SSTART voltage; restart threshold 0.1-0.3 V; discharge current 0.1-3.0 mA."+      },+      {+        "number": "25",+        "name": "RC-OSC",+        "type": "passive",+        "description": "Oscillator RC timing pin; connect ROSC (10 kΩ-100 kΩ) to VREF and COSC (1 nF-100 nF) to GND; oscillator frequency F ≈ 2/(ROSC × COSC); ramp is ≈1.2 V peak-to-peak centered at 1.6 V; 40-60 kHz typical."+      },+      {+        "number": "26",+        "name": "PWM IN",+        "type": "input",+        "description": "PWM comparator input; compared to E/A OUT to generate the PWM chop command; input current 0-30 μA; typically connected to the RC-OSC ramp for voltage-mode PWM control."+      },+      {+        "number": "27",+        "name": "E/A IN(-)",+        "type": "input",+        "description": "Error amplifier inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; input offset ±10 mV; tie to E/A OUT for unity-gain buffer configuration."+      },+      {+        "number": "28",+        "name": "E/A IN(+)",+        "type": "input",+        "description": "Error amplifier non-inverting input; input current -5 to +5 μA; common-mode input range 0 V to 3 V; voltage gain 70-90 dB; can be driven by ISENSE output, TACH-OUT filter, or external command voltage."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 25,+        "cost_usd": 0.3757,+        "at": "2026-09-22T06:31:51"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/uc2625",+        "pages": 25,+        "sha256": "dcf54a877fad8159",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 28,+        "described": 28,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file