main
Ray
Initial commit: component/tps7a1650dgnr
5522b33
TPS7A1650DGNR
Texas Instruments · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · MSOP-8-EP
TPS7A1650DGNR from Texas Instruments, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulator output pin; requires a capacitor ≥2.2 µF to GND for stability (10 µF ceramic recommended for best AC performance). |
| 2 | FB/DNC | unconnected | For the fixed-output TPS7A1650, this pin must not be connected to any electrical net, including GND or IN. |
| 3 | PG | output | Open-drain power-good output; pulls low when VOUT falls below the PG trip threshold, otherwise high-impedance; leave open or tie to GND if unused. |
| 4 | GND | power_in | Ground pin. |
| 5 | EN | input | Enable pin; regulator is enabled when VEN ≥ VEN_HI and disabled when VEN ≤ VEN_LO; can be tied to IN if unused (VEN ≤ VIN at all times). |
| 6 | NC | unconnected | No internal connection; may be left open or tied to any voltage between GND and IN. |
| 7 | DELAY | output | Delay pin; connect a capacitor to GND to set the programmable power-good delay time, or leave open if the reset/delay function is not needed. |
| 8 | IN | power_in | Regulator input supply pin; requires a capacitor ≥0.1 µF to GND for stability (10 µF ceramic recommended to reduce PCB layout sensitivity). |
| 9 | PowerPAD | power_in | Exposed thermal pad; should be soldered to the PCB and connected to the GND plane to enhance thermal performance (can be left floating but TI highly recommends GND connection). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | MSOP-8-EP |
| Category | Power Management (PMIC) |
| Pins | 9 |
CAD (KiCad official)
- Symbol:
TPS7A1650DGNR - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
tps7a1650dgnr-etched.step/tps7a1650dgnr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps7a1650dgnr.step/tps7a1650dgnr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (37 pp, sha256
180ec3f485b2772b, retrieved 2026-09-24, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS7A1650DGNR
**Texas Instruments** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · MSOP-8-EP
TPS7A1650DGNR from Texas Instruments, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulator output pin; requires a capacitor ≥2.2 µF to GND for stability (10 µF ceramic recommended for best AC performance). |
| 2 | FB/DNC | unconnected | For the fixed-output TPS7A1650, this pin must not be connected to any electrical net, including GND or IN. |
| 3 | PG | output | Open-drain power-good output; pulls low when VOUT falls below the PG trip threshold, otherwise high-impedance; leave open or tie to GND if unused. |
| 4 | GND | power_in | Ground pin. |
| 5 | EN | input | Enable pin; regulator is enabled when VEN ≥ VEN_HI and disabled when VEN ≤ VEN_LO; can be tied to IN if unused (VEN ≤ VIN at all times). |
| 6 | NC | unconnected | No internal connection; may be left open or tied to any voltage between GND and IN. |
| 7 | DELAY | output | Delay pin; connect a capacitor to GND to set the programmable power-good delay time, or leave open if the reset/delay function is not needed. |
| 8 | IN | power_in | Regulator input supply pin; requires a capacitor ≥0.1 µF to GND for stability (10 µF ceramic recommended to reduce PCB layout sensitivity). |
| 9 | PowerPAD | power_in | Exposed thermal pad; should be soldered to the PCB and connected to the GND plane to enhance thermal performance (can be left floating but TI highly recommends GND connection). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | MSOP-8-EP |
| Category | Power Management (PMIC) |
| Pins | 9 |
## CAD (KiCad official)
- Symbol: `TPS7A1650DGNR`
- Footprint: `Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm`
- 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files: `tps7a1650dgnr-etched.step` / `tps7a1650dgnr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps7a1650dgnr.step` / `tps7a1650dgnr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps7a16) (37 pp, sha256 `180ec3f485b2772b`, retrieved 2026-09-24, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps7a1650dgnr-datasheet.pdf)