Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TPS65580PWPR

Texas Instruments · DC-DC Converters · HTSSOP-20-EP

TPS65580PWPR from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Power supply input for high-side NFET drains and 5.5V linear regulator with recommended input voltage range of 4.5V to 18V.
2 VIN power_in Power supply input for high-side NFET drains and 5.5V linear regulator with recommended input voltage range of 4.5V to 18V.
3 VBST1 input Bootstrap supply input for channel 1 high-side NFET gate drive circuit with 0.1µF capacitor connection to SW1 required, absolute maximum voltage 26V (28V transient).
4 SW1 output Channel 1 switch node for high-side and low-side NFETs providing current limit comparator input with voltage range -2V to 20V (-3V to 22V transient).
5 PGND1 power_in Channel 1 power ground return for low-side MOSFET with current comparator reference function and voltage range -0.3V to 0.3V.
6 VREG5 power_out Regulated 5.5V output from internal linear regulator requiring 1.0µF ceramic bypass capacitor and providing maximum output current of 20mA at 6V input.
7 PG tri_state Open-drain power good output that pulls low when any output voltage is outside ±16% of target voltage with 2µs response time to low and 1.5ms delay to high.
8 EN1 input Enable input for converter channel 1 with H-level threshold 2.0V, L-level threshold 0.4V, and input resistance 225-900kΩ.
9 VFB1 input D-CAP2 feedback input for channel 1 connected to output voltage divider for regulation over voltage range of 0.76V to 7.0V.
10 GND power_in Signal ground reference point for feedback and control signals requiring connection of VFB returns at a single point.
11 VFB2 input D-CAP2 feedback input for channel 2 connected to output voltage divider for regulation over voltage range of 0.76V to 7.0V.
12 VFB3 input D-CAP2 feedback input for channel 3 connected to output voltage divider for regulation over voltage range of 0.76V to 7.0V.
13 EN2 input Enable input for converter channel 2 with H-level threshold 2.0V, L-level threshold 0.4V, and input resistance 225-900kΩ.
14 VBST2 input Bootstrap supply input for channel 2 high-side NFET gate drive circuit with 0.1µF capacitor connection to SW2 required, absolute maximum voltage 26V (28V transient).
15 SW2 output Channel 2 switch node for high-side and low-side NFETs providing current limit comparator input with voltage range -2V to 20V (-3V to 22V transient).
16 PGND2 power_in Channel 2 power ground return for low-side MOSFET with current comparator reference function and voltage range -0.3V to 0.3V.
17 EN3 input Enable input for converter channel 3 with H-level threshold 2.0V, L-level threshold 0.4V, and input resistance 225-900kΩ.
18 PGND3 power_in Channel 3 power ground return for low-side MOSFET with current comparator reference function and voltage range -0.3V to 0.3V.
19 SW3 output Channel 3 switch node for high-side and low-side NFETs providing current limit comparator input with voltage range -2V to 20V (-3V to 22V transient).
20 VBST3 input Bootstrap supply input for channel 3 high-side NFET gate drive circuit with 0.1µF capacitor connection to SW3 required, absolute maximum voltage 26V (28V transient).
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HTSSOP-20-EP
Category Power Management (PMIC)
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN supply current IIN 2.9 3.6 mA TA = 25°C, EN1 = EN2 = EN3 = 5 V, VFB1 = VFB2 = VFB3 = 1.0 V, Non-switching 4
VIN shutdown current IVINSDN 1.8 3 µA TA = 25°C, EN1 = EN2 = EN3 = 0 V 4
VFBx threshold voltage VVFBTHLx 752 764 776 mV TA = 25°C, VO1=3.3V, VO2=1.2V, VO3=1.5V 4
Temperature coefficient of VFBx TCVFBx -180 180 ppm/℃ On the basis of 25°C 4
Output UVP trip threshold measured on VFBx VUVP 63 68 73 % 5
PGx pull-down resistance RPG 50 85 130 Ω VPGx = 0.5 V 5
ENx input resistance RENx_IN 225 400 900 kΩ ENx = 12 V 5
Current limit (CH1) IOCL1 1.7 2 3.4 A Lout = 3.3 µH, VOUT = 3.3 V 5
Current limit (CH2) IOCL2 2.9 3.5 4.9 A Lout = 2.2 µH, VOUT = 1.2 V 5
Current limit (CH3) IOCL3 1.8 2.2 3.6 A Lout = 2.2 µH, VOUT = 1.5 V 5
VIN, EN1, EN2, EN3 input voltage range (absolute maximum) -0.3 20 V 3
VBST1, VBST2, VBST3 (absolute maximum) -0.3 26 V 3
VBST1, VBST2, VBST3 (10ns transient, absolute maximum) -0.3 28 V 3
VBST1–SW1, VBST2–SW2, VBST3–SW3 (absolute maximum) -0.3 6.5 V 3
VFB1, VFB2, VFB3 (absolute maximum) -0.3 6.5 V 3
SW1, SW2, SW3 (absolute maximum) -2 20 V 3
SW1, SW2, SW3 (10ns transient, absolute maximum) -3 22 V 3
VREG5, PG (absolute maximum) -0.3 6.5 V 3
PGND1, PGND2, PGND3 (absolute maximum) -0.3 0.3 V 3
Operating ambient temperature range TA -40 85 °C 3
Storage temperature range TSTG -55 150 °C 3
Junction temperature range (absolute maximum) TJ -40 150 °C 3
Supply input voltage range VIN 4.5 18 V 3
VBST1, VBST2, VBST3 (recommended) -0.1 24 V 3
VBST1, VBST2, VBST3 (10ns transient, recommended) -0.1 27 V 3
VBST1–SW1, VBST2–SW2, VBST3–SW3 (recommended) -0.1 5.7 V 3
VFB1, VFB2, VFB3 (recommended) -0.1 5.7 V 3
EN1, EN2, EN3 (recommended) -0.1 18 V 3
SW1, SW2, SW3 (recommended) -1 18 V 3
SW1, SW2, SW3 (10ns transient, recommended) -3 21 V 3
VREG5, PG (recommended) -0.1 5.7 V 3
PGND1, PGND2, PGND3 (recommended) -0.1 0.1 V 3
Operating free-air temperature TA -40 85 °C 3
Operating junction temperature TJ -40 150 °C 3
VREG5 UVLO threshold (rising) VUVREG5 4 V VREG5 Rising 4
VREG5 UVLO hysteresis VUVREG5 0.3 V Hysteresis 4
VREG5 output voltage VVREG5 5.5 V TA = 25°C, VIN = 12 V, IVREG = 5 mA 4
VREG5 output current IVREG5 20 mA VIN = 6 V, TA = 25°C 4
High side switch resistance for 2.5A (CH2) rDS(on)H2 160 mΩ TA = 25℃, VBST2-SW2 = 5.5 V 4
Low side switch resistance for 2.5A (CH2) rDS(on)L2 130 mΩ TA = 25℃ 4
High side switch resistance for 1.5A (CH1, CH3) rDS(on)Hx 250 mΩ TA = 25℃, VBSTx-SWx = 5.5 V 4
Low side switch resistance for 1.5A (CH1, CH3) rDS(on)Lx 230 mΩ TA = 25℃ 4
Min On Time TONminx 80 ns TA = 25°C, VOUT = 0.8V 4
Min Off Time TOFFminx 220 ns TA = 25°C, VFBx = 0.7 V 4
SW-frequency Fsw 700 kHz TA = 25°C 4
Soft-start time TSS 1.2 ms Internal soft-start time 4
PGx threshold (going high, from lower VOx) VPGTH 84 % PG from lower VOx (going high) 5
PGx threshold (going low, from higher VOx) VPGTH 116 % PG from higher VOx (going low) 5
PGx delay time (going high) TPGDLY 1.5 ms Delay for PGx going high 5
PGx delay time (going low) TPGDLY 2 µs Delay for PGx going low 5
PGOOD comparator start-up delay TPGCOMPSS 2.8 ms PGx comparator wake-up delay 5
ENx H-level threshold voltage VENH 2 V 5
ENx L-level threshold voltage VENL 0.4 V 5
Output UVP delay time TUVPDEL 0.5 ms 5
Output UVP enable delay TUVPEN 2.8 ms UVP Enable Delay 5
Thermal shutdown threshold TSD 155 °C 5
Junction-to-ambient thermal resistance θJA 40 °C/W 3
Junction-to-case (top) thermal resistance θJCtop 24.8 °C/W 3
Junction-to-board thermal resistance θJB 21.3 °C/W 3

CAD (KiCad official)

  • Symbol: TPS65580PWPR
  • Footprint: Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm
  • 3D model: HTSSOP-20-EP (KiCad packages3D, STEP)
  • 3D model files: tps65580pwpr-etched.step / tps65580pwpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps65580pwpr.step / tps65580pwpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (26 pp, sha256 374a34500cfd4753, retrieved 2026-10-01, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF