main
Ray tps65023rsbr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) e9ddc3d
{
  "schema_version": 1,
  "type": "component",
  "slug": "tps65023rsbr",
  "title": "TPS65023RSBR",
  "brief": "Texas Instruments Battery Management, WQFN-40-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power management (pmic)",
    "tps65023rsbr",
    "factory-2.0.0",
    "extractor-text"
  ],
  "component": {
    "mpn": "TPS65023RSBR",
    "manufacturer": "Texas Instruments",
    "package": "WQFN-40-EP(5x5)",
    "pin_count": 41,
    "category": "Power Management (PMIC)",
    "subcategory": "Battery Management",
    "datasheet": "https://www.ti.com/cn/lit/gpn/tps65023",
    "parts": {
      "symbol": "tps65023rsbr.kicad_sym",
      "footprint": "tps65023rsbr.kicad_mod",
      "model_3d": "tps65023rsbr-etched.glb",
      "model_3d_plain": "tps65023rsbr.glb",
      "model_3d_step": "tps65023rsbr-etched.step",
      "model_3d_step_plain": "tps65023rsbr.step",
      "lbr": "tps65023rsbr.lbr"
    },
    "distributor_links": {
      "lcsc": "C138723"
    },
    "pins": [
      {
        "number": "1",
        "name": "DEFDCDC3",
        "type": "input",
        "description": "Input to set VDCDC3 default output to 1.8 V (low) or 3.3 V (high); alternatively connect to resistor divider between VDCDC3 and GND for 0.6 V to VINDCDC3 range."
      },
      {
        "number": "2",
        "name": "VDCDC3",
        "type": "input",
        "description": "Feedback voltage sense input connected directly to VDCDC3 output for regulation control."
      },
      {
        "number": "3",
        "name": "PGND3",
        "type": "power_in",
        "description": "Power ground for VDCDC3 converter with internal connection to all GND pins."
      },
      {
        "number": "4",
        "name": "L3",
        "type": "passive",
        "description": "Switch node connection point for VDCDC3 buck converter inductor with 1 MΩ internal resistance to GND."
      },
      {
        "number": "5",
        "name": "VINDCDC3",
        "type": "power_in",
        "description": "Input voltage supply (2.5 V to 6 V) for VDCDC3 converter tied to same rail as VINDCDC1, VINDCDC2, and VCC."
      },
      {
        "number": "6",
        "name": "VINDCDC1",
        "type": "power_in",
        "description": "Input voltage supply (2.5 V to 6 V) for VDCDC1 converter tied to same rail as VINDCDC2, VINDCDC3, and VCC."
      },
      {
        "number": "7",
        "name": "L1",
        "type": "passive",
        "description": "Switch node connection point for VDCDC1 buck converter inductor with 1 MΩ internal resistance to GND."
      },
      {
        "number": "8",
        "name": "PGND1",
        "type": "power_in",
        "description": "Power ground for VDCDC1 converter with internal connection to all GND pins."
      },
      {
        "number": "9",
        "name": "VDCDC1",
        "type": "input",
        "description": "Feedback voltage sense input connected directly to VDCDC1 output for regulation control."
      },
      {
        "number": "10",
        "name": "DEFDCDC1",
        "type": "input",
        "description": "Input to set VDCDC1 default output to 1.2 V (low) or 1.6 V (high); alternatively connect to resistor divider between VDCDC1 and GND for 0.6 V to VINDCDC1 range."
      },
      {
        "number": "11",
        "name": "HOT_RESET",
        "type": "input",
        "description": "Push button input with 25-35 ms deglitch time to reset VDCDC1 output to default voltage and generate RESPWRON pulse."
      },
      {
        "number": "12",
        "name": "DEFLDO1",
        "type": "input",
        "description": "Digital input latched at power-up; combines with DEFLDO2 to set default LDO1 and LDO2 output voltage (four selectable combinations)."
      },
      {
        "number": "13",
        "name": "DEFLDO2",
        "type": "input",
        "description": "Digital input latched at power-up; combines with DEFLDO1 to set default LDO1 and LDO2 output voltage (four selectable combinations)."
      },
      {
        "number": "14",
        "name": "VSYSIN",
        "type": "input",
        "description": "System voltage input with 2.55 V (falling) to 2.65 V (rising) threshold; when above threshold, switches VRTC to VSYSIN through PMOS switch with 375 mV max dropout at 30 mA."
      },
      {
        "number": "15",
        "name": "VBACKUP",
        "type": "power_in",
        "description": "Backup battery input (2.73 V to 3.75 V) for VRTC supply when VSYSIN is below threshold; connects through PMOS switch with 375 mV max dropout at 30 mA."
      },
      {
        "number": "16",
        "name": "VRTC",
        "type": "power_out",
        "description": "Real-time clock output providing 3 V at up to 30 mA; priority-selected from VSYSIN, VBACKUP, or internal LDO; triggers RESPWRON when below 2.4 V falling or 2.52 V rising threshold."
      },
      {
        "number": "17",
        "name": "AGND2",
        "type": "power_in",
        "description": "Analog ground pin; all analog ground pins (AGND1, AGND2) connected internally on the chip."
      },
      {
        "number": "18",
        "name": "VLDO2",
        "type": "power_out",
        "description": "LDO2 output (200 mA max) with 1 V to 3.3 V selectable range via I2C or DEFLDO pins; maximum dropout 300 mV at 200 mA load."
      },
      {
        "number": "19",
        "name": "VINLDO",
        "type": "power_in",
        "description": "Input supply voltage (1.5 V to 6.5 V) for LDO1 and LDO2; can power from VCC or DC-DC converter output."
      },
      {
        "number": "20",
        "name": "VLDO1",
        "type": "power_out",
        "description": "LDO1 output (200 mA max) with 1 V to 3.15 V selectable range via I2C or DEFLDO pins; maximum dropout 300 mV at 200 mA load."
      },
      {
        "number": "21",
        "name": "LOWBAT",
        "type": "tri_state",
        "description": "Open-drain output from low-battery comparator; active low when LOWBAT_SNS is below 1 V threshold (±1%) with 40-60 mV hysteresis."
      },
      {
        "number": "22",
        "name": "LDO_EN",
        "type": "input",
        "description": "Enable input for LDO1 and LDO2; logic high enables regulators, logic low (0-0.4 V) disables them."
      },
      {
        "number": "23",
        "name": "DCDC3_EN",
        "type": "input",
        "description": "Enable input for VDCDC3 converter; logic high (1.3 × VCC minimum) enables regulator, logic low (0-0.4 V) disables it."
      },
      {
        "number": "24",
        "name": "DCDC2_EN",
        "type": "input",
        "description": "Enable input for VDCDC2 converter; logic high (1.3 × VCC minimum) enables regulator, logic low (0-0.4 V) disables it."
      },
      {
        "number": "25",
        "name": "DCDC1_EN",
        "type": "input",
        "description": "Enable input for VDCDC1 converter; logic high (1.3 × VCC minimum) enables regulator, logic low (0-0.4 V) disables it."
      },
      {
        "number": "26",
        "name": "TRESPWRON",
        "type": "input",
        "description": "Timing capacitor input for RESPWRON pulse generation; charges/discharges between 0.25 V and 1 V thresholds at 2 μA for 128 cycles (1 nF = 100 ms)."
      },
      {
        "number": "27",
        "name": "RESPWRON",
        "type": "tri_state",
        "description": "Open-drain system reset output held low until VRTC exceeds 2.52 V threshold, then released for duration set by TRESPWRON capacitor; also triggered by HOT_RESET activation."
      },
      {
        "number": "28",
        "name": "INT",
        "type": "tri_state",
        "description": "Open-drain power-good output combining all DC-DC and LDO power-good comparators; active low when any enabled supply is out of regulation (10% below target)."
      },
      {
        "number": "29",
        "name": "SDAT",
        "type": "bidirectional",
        "description": "I2C-compatible serial interface data and address line; open-drain with 4.7 kΩ external pullup to VRTC; supports fast mode up to 400 kHz."
      },
      {
        "number": "30",
        "name": "SCLK",
        "type": "input",
        "description": "I2C-compatible serial interface clock input; open-drain with 4.7 kΩ external pullup to VRTC; supports fast mode up to 400 kHz."
      },
      {
        "number": "31",
        "name": "PWRFAIL",
        "type": "tri_state",
        "description": "Open-drain power-fail output; active low when PWRFAIL_SNS is below 1 V threshold (±1%) with 40-60 mV hysteresis."
      },
      {
        "number": "32",
        "name": "DEFDCDC2",
        "type": "input",
        "description": "Input to set VDCDC2 default output to 1.8 V (low) or 3.3 V (high); alternatively connect to resistor divider between VDCDC2 and GND for 0.6 V to VINDCDC2 range."
      },
      {
        "number": "33",
        "name": "VDCDC2",
        "type": "input",
        "description": "Feedback voltage sense input connected directly to VDCDC2 output for regulation control."
      },
      {
        "number": "34",
        "name": "PGND2",
        "type": "power_in",
        "description": "Power ground for VDCDC2 converter with internal connection to all GND pins."
      },
      {
        "number": "35",
        "name": "L2",
        "type": "passive",
        "description": "Switch node connection point for VDCDC2 buck converter inductor with 1 MΩ internal resistance to GND."
      },
      {
        "number": "36",
        "name": "VINDCDC2",
        "type": "power_in",
        "description": "Input voltage supply (2.5 V to 6 V) for VDCDC2 converter tied to same rail as VINDCDC1, VINDCDC3, and VCC."
      },
      {
        "number": "37",
        "name": "VCC",
        "type": "power_in",
        "description": "Analog and digital supply voltage (2.5 V to 6 V) for all DC-DC converter control circuits and I2C interface; must connect to same rail as VINDCDC1/2/3."
      },
      {
        "number": "38",
        "name": "PWRFAIL_SNS",
        "type": "input",
        "description": "Analog input to power-fail comparator with 1 V threshold (±1%) and 40-60 mV hysteresis; drives PWRFAIL open-drain output."
      },
      {
        "number": "39",
        "name": "LOWBAT_SNS",
        "type": "input",
        "description": "Analog input to low-battery comparator with 1 V threshold (±1%) and 40-60 mV hysteresis; drives LOWBAT open-drain output."
      },
      {
        "number": "40",
        "name": "AGND1",
        "type": "power_in",
        "description": "Analog ground pin; all analog ground pins (AGND1, AGND2) connected internally on the chip."
      },
      {
        "number": "41",
        "name": "EP",
        "type": "passive",
        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.2",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.2",
        "primary_model": "claude-haiku-4-5-20251001",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "exposed pad 41 added from the footprint",
          "dropped thermal pad ['EP'] absent from footprint"
        ],
        "pages_sent": 56,
        "cost_usd": 0.7005,
        "at": "2026-09-24T02:40:34"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/tps65023",
        "pages": 56,
        "sha256": "1a96eac1a7a70fa5",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 41,
        "described": 41,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "tps65023rsbr.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          5,
          5,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "8f37bc7a9aab4742c34f137d9822c0352acc227532830034555744338483cdfc",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "tps65023rsbr-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          5,
          5,
          0.77
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "115393f6c809342ed6fcf38beeb7471f62608441a1d58776d52e3fb62abe063f",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Texas Instruments",
      "Package": "WQFN-40-EP(5x5)",
      "Category": "Power Management (PMIC)",
      "Pins": "41"
    }
  },
  "variants": [],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "tps65023rsbr"
  ],
  "discovery_pitch": "TPS65023RSBR (Texas Instruments) component page: datasheet pinout, KiCad symbol, footprint and 3D.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "tps65023rsbr.kicad_sym",
    "tps65023rsbr.kicad_mod",
    "tps65023rsbr.glb",
    "tps65023rsbr.step",
    "tps65023rsbr.lbr",
    "docs/hero.png",
    "docs/tps65023rsbr-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  }
}