main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs tps53647rtar: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers tps53647rtar: viewers · Ray
package.json tps53647rtar: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json tps53647rtar: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/tps53647rtar · Ray
tps53647rtar-etched.fit.json tps53647rtar: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps53647rtar-etched.glb tps53647rtar: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps53647rtar-etched.step tps53647rtar: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps53647rtar.glb Publish 0.1.0 · Ray
tps53647rtar.kicad_mod Publish 0.1.0 · Ray
tps53647rtar.kicad_sym Publish 0.1.0 · Ray
tps53647rtar.lbr Publish 0.1.0 · Ray
tps53647rtar.step Publish 0.1.0 · Ray

TPS53647RTAR

Texas Instruments · AC-DC Controllers And Regulators · WQFN-40-EP(6x6)

TPS53647RTAR from Texas Instruments, in a WQFN-40-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OCL-R input Voltage divider to VREF pin; resistor (ROCL-R) to GND sets per-phase overcurrent limit level and selects ramp amplitude from four options.
2 IMON output Analog current monitor output; resistor to GND generates output voltage proportional to sum of phase currents at 5 mV/A scaling.
3 CSP1 input Positive current sense input for phase 1; connect to IOUT pin of TI smart power stages; tie CSP1 to V3R3 to disable phase 1.
4 CSP2 input Positive current sense input for phase 2; connect to IOUT pin of TI smart power stages; tie CSP2 to V3R3 to disable phase 2.
5 CSP3 input Positive current sense input for phase 3; connect to IOUT pin of TI smart power stages; tie CSP3 to V3R3 to disable phase 3.
6 CSP4 input Positive current sense input for phase 4; connect to IOUT pin of TI smart power stages; tie CSP4 to V3R3 to disable phase 4.
7 NC unconnected No internal connection; leave the pin open or pull up to V3R3 pin.
8 NC unconnected No connection.
9 VSP input Positive input of the remote voltage sense amplifier; connect directly to the output voltage being regulated.
10 VSN input Negative input of the remote voltage sense amplifier; connect directly to GND of the load for accurate output voltage sensing.
11 COMP output Output of the gM error amplifier; resistors and capacitors between this pin and VREF pin set the feedback compensation network.
12 ISUM output Current sum output; resistor (RISUM) to VREF pin determines the load-line droop voltage as function of output current.
13 VREF power_out 1.7-V, 500-µA, LDO reference voltage output; bypass to GND with 0.33 µF capacitor; connect to REFIN of TI power stages as current-sense reference.
14 V3R3 power_out 3.3-V LDO output from V5; bypass to GND with 1-µF or larger ceramic capacitor; powers internal digital circuits and provides pull-up source for open-drain outputs.
15 V5 power_in 5-V power input; bypass to GND with 1-µF or larger ceramic capacitor; supplies all internal analog circuits; rated 4.5 V to 5.5 V operating range.
16 VIN power_in Input voltage supply; also used for input voltage sensing for on-time control and UVLO detection; rated 4.5 V to 17 V operating range.
17 GND power_in Ground pin (IC ground); primary ground reference for all internal circuits.
18 VR_RDY tri_state Power good open-drain output; typically pulled up to V3R3 through 3-kΩ or larger resistor; asserts high when output voltage in regulation within UVP/OVP thresholds.
19 VR_HOT tri_state Thermal flag open-drain output, active low; typically pulled up to V3R3 through 3-kΩ or larger resistor; asserts low when sensed temperature exceeds 110°C default warning threshold.
20 GND power_in Ground pin; connect to GND (noted as not IC ground pin in schematic context).
21 RESET input Reset pin; if low for more than 1000 ns, controller pulls output voltage to VBOOT level for adaptive voltage scaling reset function.
22 GND power_in Ground pin; connect to GND (noted as not IC ground pin in schematic context).
23 ENABLE input VR enable control pin; 1-V I/O level with 100-ns debounce; high enables output, low disables output and enters standby mode.
24 PMB_CLK input I2C PMBus clock input; 3.3-V and 1.8-V logic level compatible; part of PMBus communication protocol supporting 100 kHz and 400 kHz bus speeds.
25 PMB_ALERT tri_state I2C PMBus interrupt line, open-drain output; 3.3-V and 1.8-V logic level compatible; asserts low to alert master of fault condition on PMBus.
26 PMB_DIO bidirectional I2C PMBus digital I/O line; 3.3-V and 1.8-V logic level compatible; used for bidirectional PMBus data transmission and communication protocol.
27 VR_FAULT tri_state VR fault indicator, open-drain output, active low; asserts for input overcurrent, over-temperature, output overvoltage, and power stage faults; typically pulled up to V3R3 or left floating if not used.
28 ADDR-TRISE input Voltage divider to VREF pin; resistor (RADDR-TRISE) to GND sets 3 bits for soft-start slew rate and boot voltage LSB; voltage level sets 4 bits of PMBus address (16 possible).
29 SLEW-MODE input Voltage divider to VREF pin; resistor (RSLEW-MODE) to GND selects output voltage change slew rate (0.34 to 2.74 mV/µs); voltage sets 4-bit operation mode bits for DAC mode, phase interleaving, dynamic phase shedding, and zero load-line.
30 O-USR input Voltage divider to VREF pin; resistor (RO-USR) to GND selects one of 7 OSR (overshoot reduction) thresholds or OFF; voltage sets one of 7 USR (undershoot reduction) levels or OFF for transient improvement.
31 VBOOT input Voltage divider to VREF pin; resistor (RVBOOT) to GND sets bits 3:1 of boot voltage VID; voltage sets bits 7:4, total 7 bits set output voltage at startup from 0.5 V to 2.5 V.
32 F-IMAX input Voltage divider to VREF pin; resistor (RF-IMAX) to GND sets switching frequency from 300 kHz to 1 MHz; voltage sets maximum operating current (IMAX) with 8-bit A/D where IMAX = (VF-IMAX/VREF) × 256 - 0.5.
33 NC unconnected No connection.
34 NC unconnected No connection.
35 PWM4 output PWM signal output for phase 4; 3.3-V logic output; high turns on high-side MOSFET, low turns on low-side MOSFET, tri-state (1.7 V) for both MOSFETs off.
36 PWM3 output PWM signal output for phase 3; 3.3-V logic output; high turns on high-side MOSFET, low turns on low-side MOSFET, tri-state (1.7 V) for both MOSFETs off.
37 PWM2 output PWM signal output for phase 2; 3.3-V logic output; high turns on high-side MOSFET, low turns on low-side MOSFET, tri-state (1.7 V) for both MOSFETs off.
38 PWM1 output PWM signal output for phase 1; 3.3-V logic output; high turns on high-side MOSFET, low turns on low-side MOSFET, tri-state (1.7 V) for both MOSFETs off.
39 SKIP-NVM output SKIP-NVM output pin; resistor (RSKIP-NVM) to GND sets pinstrap or NVM configuration mode; can connect to FCCM pin of TI power stages for SKIP or FCCM operation mode selection.
40 TSEN input Temperature sense input; connect to TAO/FAULT pin of TI smart power stages to sense highest die temperature and power stage fault signals; 0°C to 127.9°C measurement range.
41 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-40-EP(6x6)
Category Power Management (PMIC)
Pins 41

CAD (KiCad official)

  • Symbol: TPS53647RTAR
  • Footprint: Package_DFN_QFN:QFN-40-1EP_6x6mm_P0.5mm_EP4.6x4.6mm
  • 3D model: WQFN-40-EP(6x6) (KiCad packages3D, STEP)
  • 3D model files: tps53647rtar-etched.step / tps53647rtar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps53647rtar.step / tps53647rtar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (123 pp, sha256 2a0c7fc1d7dab847, retrieved 2026-09-27, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF