main
History Download
Ray Initial commit: component/tps51220artvr 9232318

TPS51220ARTVR

Texas Instruments · DC-DC Converters · WQFN-32-EP(5x5)

TPS51220ARTVR from Texas Instruments, in a WQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DRVH1 output High-side MOSFET gate driver output for channel 1; source 1.7 Ω, sink 1.0 Ω, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage.
2 V5SW power_in VREG5 switchover power supply input; when EN1 is high, PGOOD1 is good and V5SW > 4.8 V, the internal 5-V LDO is shut off and VREG5 is switched to V5SW.
3 RF bidirectional Frequency setting pin; connect a resistor to signal GND to set switching frequency, or connect to an external clock for synchronization.
4 EN1 input Channel 1 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here.
5 PGOOD1 output Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ.
6 SKIPSEL1 input Skip mode selection pin for channel 1; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips.
7 CSP1 bidirectional Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR.
8 CSN1 input Current sense comparator (-) input for channel 1; used as power supply for the channel-1 current sense circuit at 5 V or higher output settings, and as the output discharge terminal.
9 VFB1 input SMPS voltage feedback input for channel 1; connect the feedback resistor divider, referenced to signal GND.
10 COMP1 input Loop compensation pin for channel 1 current-mode error amplifier output; connect R (and C if required) from this pin to VREF2 for loop compensation.
11 FUNC input Control architecture and OVP selection pin: GND=Current mode/OVP enable, VREF2=D-CAP mode/OVP disable, VREG3=D-CAP mode/OVP enable, VREG5=Current mode/OVP disable.
12 EN input VREF2 and VREG5 linear regulator enable pin; apply greater than 1.2 V and less than 6 V to turn on; connect to GND to disable.
13 VREF2 power_out 2-V reference output; bypass to signal GND with 0.22-µF ceramic capacitance.
14 TRIP input Overcurrent trip level and discharge mode selection pin: GND=V(OCL-ULV) discharge on, VREF2=V(OCL-ULV) discharge off, VREG3=V(OCL-LV) discharge off, VREG5=V(OCL-LV) discharge on.
15 COMP2 input Ramp compensation/loop compensation pin for channel 2; connect R (10 kΩ typical, 6 kΩ-20 kΩ range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation.
16 VFB2 input SMPS voltage feedback input for channel 2; connect the feedback resistor divider, referenced to signal GND.
17 CSN2 input Current sense comparator (-) input for channel 2; used as power supply for the channel-2 current sense circuit at 5 V or higher output settings, and as the output discharge terminal.
18 CSP2 bidirectional Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR.
19 SKIPSEL2 input Skip mode selection pin for channel 2; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips.
20 PGOOD2 output Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ.
21 EN2 input Channel 2 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here.
22 VREG3 power_out Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-µF ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW.
23 VIN power_in Supply input for the 5-V and 3.3-V linear regulators; typically connected to VBAT.
24 DRVH2 output High-side MOSFET gate driver output for channel 2; source 1.7 Ω, sink 1.0 Ω, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage.
25 SW2 bidirectional High-side MOSFET gate driver return for channel 2 (switch node).
26 VBST2 power_in Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed.
27 DRVL2 output Low-side MOSFET gate driver output for channel 2; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver.
28 GND power_in Signal ground reference for the device.
29 VREG5 power_out 5-V, 100-mA LDO output; bypass to power GND with a 10-µF (min 4.7-µF) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided.
30 DRVL1 output Low-side MOSFET gate driver output for channel 1; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver.
31 VBST1 power_in Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed.
32 SW1 bidirectional High-side MOSFET gate driver return for channel 1 (switch node).
33 PowerPAD power_in Exposed thermal pad (PowerPAD); must be soldered to the PCB and connected to the internal GND plane through five or more 0.33-mm vias for thermal dissipation; do not connect the GND pin to this pad on the surface layer.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-32-EP(5x5)
Category Power Management (PMIC)
Pins 33

CAD (KiCad official)

  • Symbol: TPS51220ARTVR
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: WQFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: tps51220artvr-etched.step / tps51220artvr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps51220artvr.step / tps51220artvr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (55 pp, sha256 6e980b37451f3708, retrieved 2026-09-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF