← Commit history

Initial commit: component/tps51220artvr

Ray ·9232318454 ·
2 files changed +362
README.mdadded+69
@@ -0,0 +1,69 @@+# TPS51220ARTVR++**Texas Instruments** · DC-DC Converters · WQFN-32-EP(5x5)++TPS51220ARTVR from Texas Instruments, in a WQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | DRVH1 | output | High-side MOSFET gate driver output for channel 1; source 1.7 Ω, sink 1.0 Ω, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage. |+| 2 | V5SW | power_in | VREG5 switchover power supply input; when EN1 is high, PGOOD1 is good and V5SW > 4.8 V, the internal 5-V LDO is shut off and VREG5 is switched to V5SW. |+| 3 | RF | bidirectional | Frequency setting pin; connect a resistor to signal GND to set switching frequency, or connect to an external clock for synchronization. |+| 4 | EN1 | input | Channel 1 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here. |+| 5 | PGOOD1 | output | Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ. |+| 6 | SKIPSEL1 | input | Skip mode selection pin for channel 1; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips. |+| 7 | CSP1 | bidirectional | Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR. |+| 8 | CSN1 | input | Current sense comparator (-) input for channel 1; used as power supply for the channel-1 current sense circuit at 5 V or higher output settings, and as the output discharge terminal. |+| 9 | VFB1 | input | SMPS voltage feedback input for channel 1; connect the feedback resistor divider, referenced to signal GND. |+| 10 | COMP1 | input | Loop compensation pin for channel 1 current-mode error amplifier output; connect R (and C if required) from this pin to VREF2 for loop compensation. |+| 11 | FUNC | input | Control architecture and OVP selection pin: GND=Current mode/OVP enable, VREF2=D-CAP mode/OVP disable, VREG3=D-CAP mode/OVP enable, VREG5=Current mode/OVP disable. |+| 12 | EN | input | VREF2 and VREG5 linear regulator enable pin; apply greater than 1.2 V and less than 6 V to turn on; connect to GND to disable. |+| 13 | VREF2 | power_out | 2-V reference output; bypass to signal GND with 0.22-µF ceramic capacitance. |+| 14 | TRIP | input | Overcurrent trip level and discharge mode selection pin: GND=V(OCL-ULV) discharge on, VREF2=V(OCL-ULV) discharge off, VREG3=V(OCL-LV) discharge off, VREG5=V(OCL-LV) discharge on. |+| 15 | COMP2 | input | Ramp compensation/loop compensation pin for channel 2; connect R (10 kΩ typical, 6 kΩ-20 kΩ range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation. |+| 16 | VFB2 | input | SMPS voltage feedback input for channel 2; connect the feedback resistor divider, referenced to signal GND. |+| 17 | CSN2 | input | Current sense comparator (-) input for channel 2; used as power supply for the channel-2 current sense circuit at 5 V or higher output settings, and as the output discharge terminal. |+| 18 | CSP2 | bidirectional | Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR. |+| 19 | SKIPSEL2 | input | Skip mode selection pin for channel 2; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips. |+| 20 | PGOOD2 | output | Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ. |+| 21 | EN2 | input | Channel 2 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here. |+| 22 | VREG3 | power_out | Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-µF ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW. |+| 23 | VIN | power_in | Supply input for the 5-V and 3.3-V linear regulators; typically connected to VBAT. |+| 24 | DRVH2 | output | High-side MOSFET gate driver output for channel 2; source 1.7 Ω, sink 1.0 Ω, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage. |+| 25 | SW2 | bidirectional | High-side MOSFET gate driver return for channel 2 (switch node). |+| 26 | VBST2 | power_in | Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed. |+| 27 | DRVL2 | output | Low-side MOSFET gate driver output for channel 2; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver. |+| 28 | GND | power_in | Signal ground reference for the device. |+| 29 | VREG5 | power_out | 5-V, 100-mA LDO output; bypass to power GND with a 10-µF (min 4.7-µF) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided. |+| 30 | DRVL1 | output | Low-side MOSFET gate driver output for channel 1; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver. |+| 31 | VBST1 | power_in | Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed. |+| 32 | SW1 | bidirectional | High-side MOSFET gate driver return for channel 1 (switch node). |+| 33 | PowerPAD | power_in | Exposed thermal pad (PowerPAD); must be soldered to the PCB and connected to the internal GND plane through five or more 0.33-mm vias for thermal dissipation; do not connect the GND pin to this pad on the surface layer. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-32-EP(5x5) |+| Category | Power Management (PMIC) |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `TPS51220ARTVR`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: WQFN-32-EP(5x5) (KiCad packages3D, STEP)+- 3D model files: `tps51220artvr-etched.step` / `tps51220artvr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps51220artvr.step` / `tps51220artvr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps51220a) (55 pp, sha256 `6e980b37451f3708`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps51220artvr-datasheet.pdf)
page.jsonadded+293
@@ -0,0 +1,293 @@+{+  "slug": "tps51220artvr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, WQFN-32-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps51220artvr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps51220artvr.kicad_sym",+    "tps51220artvr.kicad_mod",+    "tps51220artvr.glb",+    "tps51220artvr.step",+    "tps51220artvr.lbr",+    "docs/hero.png",+    "docs/tps51220artvr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS51220ARTVR",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-32-EP(5x5)",+    "pin_count": 33,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps51220a",+    "parts": {+      "symbol": "tps51220artvr.kicad_sym",+      "footprint": "tps51220artvr.kicad_mod",+      "model_3d": "tps51220artvr-etched.glb",+      "model_3d_plain": "tps51220artvr.glb",+      "model_3d_step": "tps51220artvr-etched.step",+      "model_3d_step_plain": "tps51220artvr.step",+      "lbr": "tps51220artvr.lbr"+    },+    "distributor_links": {+      "lcsc": "C201651"+    },+    "pins": [+      {+        "number": "1",+        "name": "DRVH1",+        "type": "output",+        "description": "High-side MOSFET gate driver output for channel 1; source 1.7 Ω, sink 1.0 Ω, SW1-node referenced floating driver, drive voltage corresponds to VBST1 to SW1 voltage."+      },+      {+        "number": "2",+        "name": "V5SW",+        "type": "power_in",+        "description": "VREG5 switchover power supply input; when EN1 is high, PGOOD1 is good and V5SW > 4.8 V, the internal 5-V LDO is shut off and VREG5 is switched to V5SW."+      },+      {+        "number": "3",+        "name": "RF",+        "type": "bidirectional",+        "description": "Frequency setting pin; connect a resistor to signal GND to set switching frequency, or connect to an external clock for synchronization."+      },+      {+        "number": "4",+        "name": "EN1",+        "type": "input",+        "description": "Channel 1 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here."+      },+      {+        "number": "5",+        "name": "PGOOD1",+        "type": "output",+        "description": "Powergood window comparator output for channel 1; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ."+      },+      {+        "number": "6",+        "name": "SKIPSEL1",+        "type": "input",+        "description": "Skip mode selection pin for channel 1; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips."+      },+      {+        "number": "7",+        "name": "CSP1",+        "type": "bidirectional",+        "description": "Current sense comparator (+) input for channel 1; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR."+      },+      {+        "number": "8",+        "name": "CSN1",+        "type": "input",+        "description": "Current sense comparator (-) input for channel 1; used as power supply for the channel-1 current sense circuit at 5 V or higher output settings, and as the output discharge terminal."+      },+      {+        "number": "9",+        "name": "VFB1",+        "type": "input",+        "description": "SMPS voltage feedback input for channel 1; connect the feedback resistor divider, referenced to signal GND."+      },+      {+        "number": "10",+        "name": "COMP1",+        "type": "input",+        "description": "Loop compensation pin for channel 1 current-mode error amplifier output; connect R (and C if required) from this pin to VREF2 for loop compensation."+      },+      {+        "number": "11",+        "name": "FUNC",+        "type": "input",+        "description": "Control architecture and OVP selection pin: GND=Current mode/OVP enable, VREF2=D-CAP mode/OVP disable, VREG3=D-CAP mode/OVP enable, VREG5=Current mode/OVP disable."+      },+      {+        "number": "12",+        "name": "EN",+        "type": "input",+        "description": "VREF2 and VREG5 linear regulator enable pin; apply greater than 1.2 V and less than 6 V to turn on; connect to GND to disable."+      },+      {+        "number": "13",+        "name": "VREF2",+        "type": "power_out",+        "description": "2-V reference output; bypass to signal GND with 0.22-µF ceramic capacitance."+      },+      {+        "number": "14",+        "name": "TRIP",+        "type": "input",+        "description": "Overcurrent trip level and discharge mode selection pin: GND=V(OCL-ULV) discharge on, VREF2=V(OCL-ULV) discharge off, VREG3=V(OCL-LV) discharge off, VREG5=V(OCL-LV) discharge on."+      },+      {+        "number": "15",+        "name": "COMP2",+        "type": "input",+        "description": "Ramp compensation/loop compensation pin for channel 2; connect R (10 kΩ typical, 6 kΩ-20 kΩ range) from this pin to VREF2 for D-CAP mode ramp compensation or current-mode loop compensation."+      },+      {+        "number": "16",+        "name": "VFB2",+        "type": "input",+        "description": "SMPS voltage feedback input for channel 2; connect the feedback resistor divider, referenced to signal GND."+      },+      {+        "number": "17",+        "name": "CSN2",+        "type": "input",+        "description": "Current sense comparator (-) input for channel 2; used as power supply for the channel-2 current sense circuit at 5 V or higher output settings, and as the output discharge terminal."+      },+      {+        "number": "18",+        "name": "CSP2",+        "type": "bidirectional",+        "description": "Current sense comparator (+) input for channel 2; use an RC network with X5R/X7R ceramic capacitor (0.1 µF typical) to extract voltage drop across DCR."+      },+      {+        "number": "19",+        "name": "SKIPSEL2",+        "type": "input",+        "description": "Skip mode selection pin for channel 2; GND=continuous conduction, VREF2=Auto Skip, VREG3=OOA Auto Skip max 7 skips, VREG5=OOA Auto Skip max 15 skips."+      },+      {+        "number": "20",+        "name": "PGOOD2",+        "type": "output",+        "description": "Powergood window comparator output for channel 2; recommended applied voltage less than 6 V, recommended pull-up resistance 100 kΩ to 1 MΩ."+      },+      {+        "number": "21",+        "name": "EN2",+        "type": "input",+        "description": "Channel 2 SMPS enable pin; apply greater than 0.55 V and less than 6 V to turn on, or leave floating; connect to GND to disable; adjustable soft-start capacitance may be attached here."+      },+      {+        "number": "22",+        "name": "VREG3",+        "type": "power_out",+        "description": "Always-alive 3.3-V, 10-mA LDO output; bypass to signal GND with more than 1-µF ceramic capacitance; runs from VIN or from VREG5 when switched over to V5SW."+      },+      {+        "number": "23",+        "name": "VIN",+        "type": "power_in",+        "description": "Supply input for the 5-V and 3.3-V linear regulators; typically connected to VBAT."+      },+      {+        "number": "24",+        "name": "DRVH2",+        "type": "output",+        "description": "High-side MOSFET gate driver output for channel 2; source 1.7 Ω, sink 1.0 Ω, SW2-node referenced floating driver, drive voltage corresponds to VBST2 to SW2 voltage."+      },+      {+        "number": "25",+        "name": "SW2",+        "type": "bidirectional",+        "description": "High-side MOSFET gate driver return for channel 2 (switch node)."+      },+      {+        "number": "26",+        "name": "VBST2",+        "type": "power_in",+        "description": "Supply input for channel-2 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW2; an optional Schottky diode from VREG5 is allowed."+      },+      {+        "number": "27",+        "name": "DRVL2",+        "type": "output",+        "description": "Low-side MOSFET gate driver output for channel 2; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver."+      },+      {+        "number": "28",+        "name": "GND",+        "type": "power_in",+        "description": "Signal ground reference for the device."+      },+      {+        "number": "29",+        "name": "VREG5",+        "type": "power_out",+        "description": "5-V, 100-mA LDO output; bypass to power GND with a 10-µF (min 4.7-µF) ceramic capacitor; runs from VIN, internally connected to VBST and DRVL, shuts off with EN, switches over to V5SW when 4.8 V or above is provided."+      },+      {+        "number": "30",+        "name": "DRVL1",+        "type": "output",+        "description": "Low-side MOSFET gate driver output for channel 1; source 1.3 Ω, sink 0.7 Ω, GND-referenced driver."+      },+      {+        "number": "31",+        "name": "VBST1",+        "type": "power_in",+        "description": "Supply input for channel-1 high-side N-channel FET driver (boot strap terminal); connect a capacitor (0.1 µF or greater recommended) from this pin to SW1; an optional Schottky diode from VREG5 is allowed."+      },+      {+        "number": "32",+        "name": "SW1",+        "type": "bidirectional",+        "description": "High-side MOSFET gate driver return for channel 1 (switch node)."+      },+      {+        "number": "33",+        "name": "PowerPAD",+        "type": "power_in",+        "description": "Exposed thermal pad (PowerPAD); must be soldered to the PCB and connected to the internal GND plane through five or more 0.33-mm vias for thermal dissipation; do not connect the GND pin to this pad on the surface layer."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 33 added from the footprint"+        ],+        "pages_sent": 55,+        "cost_usd": 0.5489,+        "at": "2026-09-23T13:06:11"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps51220a",+        "pages": 55,+        "sha256": "6e980b37451f3708",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 33,+        "described": 33,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file