Generated by kicad-footprint-generator · KiCad file format 20260206
TPS40211DGQR
Texas Instruments · DC-DC Converters · MSOP-10-EP
TPS40211DGQR from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RC | input | Oscillator frequency setting pin; connect resistor between RC and VDD and capacitor between RC and GND to set switching frequency. |
| 2 | SS | input | Soft start timing pin; connect capacitor to GND to program soft start ramp time and overcurrent retry timeout duration. |
| 3 | DIS/EN | input | Disable/enable pin with internal 1 MΩ pull-down to GND; pulling above 1.2 V typical disables device and BP regulator; below 1.05 V typical enables device. |
| 4 | COMP | output | Error amplifier output; connect loop compensation network between COMP and FB pins for control loop response. |
| 5 | FB | input | Error amplifier inverting input; connect voltage divider from output to this pin to set output voltage; compensation network between FB and COMP pins. |
| 6 | GND | power_in | Device ground reference. |
| 7 | ISNS | input | Current sense input; connect external sense resistor between this pin and GND; overcurrent protection triggers when voltage exceeds 150 mV typical. |
| 8 | GDRV | output | Gate drive output for N-channel power MOSFET; provides up to 400 mA source and sink current capability. |
| 9 | BP | power_out | Linear regulator output pin; 8 V nominal with 7 V to 9 V operating range; bypass with 1.0 μF capacitor to GND. |
| 10 | VDD | power_in | Input power supply voltage; accepts 4.5 V to 52 V; bypass capacitor to GND required; can connect to converter output for slope compensation. |
| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | MSOP-10-EP |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 反馈电压 TPS40211 (COMP=FB, TJ=25°C) | VFB | 254 | 260 | 266 | mV | COMP=FB, 4.5≤VDD≤52V, TJ=25°C | 5 |
| 反馈电压 TPS40211 (全温度) | VFB | 250 | 260 | 270 | mV | COMP=FB, 4.5≤VDD≤52V, -40°C≤TJ≤125°C | 5 |
| VDD 输入电压范围 | VDD | 4.5 | 52 | V | 5 | ||
| IDD 工作电流 | IDD | 1.5 | 2.5 | mA | 4.5≤VDD≤52V, 无开关, VDIS<0.8 | 5 | |
| IDD 工作电流 (使能电平) | IDD | 10 | 20 | μA | 2.5≤VDIS≤7V | 5 | |
| IDD 工作电流 (VDD<UVLO) | IDD | 530 | μA | VDD<VUVLO(on), VDIS<0.8 | 5 | ||
| 欠压锁定导通阈值电压 | VUVLO(on) | 4 | 4.25 | 4.5 | V | 5 | |
| UVLO 迟滞 | VUVLO(hyst) | 140 | 195 | 240 | mV | 5 | |
| 振荡器频率范围 | fOSC | 35 | 1000 | kHz | 5 | ||
| 振荡器频率 | fOSC | 260 | 300 | 340 | kHz | RRC=182kΩ, CRC=330pF | 5 |
| 频率线性调整 | -20 | 7 | % | 4.5≤VDD≤52V | 5 | ||
| 斜率补偿斜坡 | VSLP | 520 | 620 | 720 | mV | 5 | |
| 最小脉宽 tON(min) | tON(min) | 275 | 400 | ns | VDD = 12V | 5 | |
| 最小脉宽 tON(min) | tON(min) | 90 | 200 | ns | VDD = 30V | 5 | |
| 最短关断时间 tOFF(min) | tOFF(min) | 170 | 200 | ns | 5 | ||
| 软启动 RSS(chg) 充电电阻 | RSS(chg) | 320 | 430 | 600 | kΩ | 5 | |
| 软启动 RSS(dchg) 放电电阻 | RSS(dchg) | 840 | 1200 | 1600 | kΩ | 5 | |
| 单位增益带宽积 GBWP | GBWP | 1.5 | 3 | MHz | 5 | ||
| 开环增益 AOL | AOL | 60 | 80 | dB | 5 | ||
| 输入偏置电流 IIB(FB) | IIB(FB) | 100 | 300 | nA | 流出 FB 引脚的电流 | 5 | |
| 输出拉电流 ICOMP(src) | ICOMP(src) | 100 | 250 | μA | VFB = 0.6V, VCOMP = 1V | 5 | |
| 输出灌电流 ICOMP(snk) | ICOMP(snk) | 1.2 | 2.5 | mA | VFB = 1.2V, VCOMP = 1V | 5 | |
| 过流检测阈值 (ISNS 引脚) | VISNS(oc) | 120 | 150 | 180 | mV | 4.5≤VDD<52V, -40°C≤TJ≤125°C | 5 |
| 过流复位阈值电压 (SS 引脚) | VSS(rst) | 100 | 150 | 350 | mV | 5 | |
| 电流检测放大器增益 ACS | ACS | 5.6 | 7.2 | V/V | 6 | ||
| 电流检测输入偏置电流 IB(ISNS) | IB(ISNS) | 1 | 3 | μA | 6 | ||
| 栅极驱动器拉电流 IGDRV(src) | IGDRV(src) | 375 | 400 | mA | VGDRV = 4V, TJ = 25°C | 6 | |
| 栅极驱动器灌电流 IGDRV(snk) | IGDRV(snk) | 330 | 400 | mA | VGDRV = 4V, TJ = 25°C | 6 | |
| 旁路电压输出 VBP | VBP | 7 | 8 | 9 | V | 0mA < IBP < 15mA | 6 |
| 使能导通电压 VDIS(en) | VDIS(en) | 0.7 | 1.3 | V | 6 | ||
| 迟滞电压 VDIS(hys) | VDIS(hys) | 25 | 130 | 220 | mV | 6 | |
| DIS 引脚下拉电阻 RDIS | RDIS | 0.7 | 1.1 | 1.5 | mΩ | 6 | |
| 过流占空比 DOC | DOC | 2 | % | 5 | |||
| 前缘消隐 TBLNK | TBLNK | 75 | ns | 5 | |||
| 软启动失调电压 VSS(ofst) | VSS(ofst) | 700 | mV | 从 SS 引脚到误差放大器输入端 | 5 | ||
| 谷值电压 VVLY | VVLY | 1.2 | V | 5 | |||
| VDD 绝对最大输入电压 | VDD | -0.3 | 52 | V | 4 | ||
| RC, SS, FB, DIS/EN 绝对最大电压 | -0.3 | 10 | V | 4 | |||
| ISNS 绝对最大电压 | -0.3 | 8 | V | 4 | |||
| COMP, BP, GDRV 绝对最大输出电压 | -0.3 | 9 | V | 4 | |||
| TJ 工作结温 (绝对最大) | TJ | -40 | 150 | °C | 4 | ||
| 贮存温度 Tstg | Tstg | -55 | 150 | °C | 4 | ||
| VDD 输入电压 (推荐) | VDD | 4.5 | 52 | V | 4 | ||
| TJ 工作结温 (推荐) | TJ | -40 | 125 | °C | 4 | ||
| 结至环境热阻 RθJA (HVSSOP 列) | RθJA | 67.2 | °C/W | HVSSOP 10 引脚 | 4 | ||
| 结至外壳(顶部)热阻 RθJC(top) (HVSSOP 列) | RθJC(top) | 50.5 | °C/W | HVSSOP 10 引脚 | 4 | ||
| 结至电路板热阻 RθJB (HVSSOP 列) | RθJB | 41 | °C/W | HVSSOP 10 引脚 | 4 | ||
| 结至顶部特征参数 ψJT (HVSSOP 列) | ψJT | 2.4 | °C/W | HVSSOP 10 引脚 | 4 | ||
| 结至电路板特征参数 ψJB (HVSSOP 列) | ψJB | 40.7 | °C/W | HVSSOP 10 引脚 | 4 | ||
| 结至外壳(底部)热阻 RθJC(bot) (HVSSOP 列) | RθJC(bot) | 15.6 | °C/W | HVSSOP 10 引脚 | 4 |
CAD (KiCad official)
- Symbol:
TPS40211DGQR - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
tps40211dgqr-etched.step/tps40211dgqr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps40211dgqr.step/tps40211dgqr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (50 pp, sha256
7213a870ac0ef0d9, retrieved 2026-09-23, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).