main
History Download
Ray tps40211dgqr: specified limits as data (metadata.characteristics, 50 rows from the datasheet) da4802e

TPS40211DGQR

Texas Instruments · DC-DC Converters · MSOP-10-EP

TPS40211DGQR from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RC input Oscillator frequency setting pin; connect resistor between RC and VDD and capacitor between RC and GND to set switching frequency.
2 SS input Soft start timing pin; connect capacitor to GND to program soft start ramp time and overcurrent retry timeout duration.
3 DIS/EN input Disable/enable pin with internal 1 MΩ pull-down to GND; pulling above 1.2 V typical disables device and BP regulator; below 1.05 V typical enables device.
4 COMP output Error amplifier output; connect loop compensation network between COMP and FB pins for control loop response.
5 FB input Error amplifier inverting input; connect voltage divider from output to this pin to set output voltage; compensation network between FB and COMP pins.
6 GND power_in Device ground reference.
7 ISNS input Current sense input; connect external sense resistor between this pin and GND; overcurrent protection triggers when voltage exceeds 150 mV typical.
8 GDRV output Gate drive output for N-channel power MOSFET; provides up to 400 mA source and sink current capability.
9 BP power_out Linear regulator output pin; 8 V nominal with 7 V to 9 V operating range; bypass with 1.0 μF capacitor to GND.
10 VDD power_in Input power supply voltage; accepts 4.5 V to 52 V; bypass capacitor to GND required; can connect to converter output for slope compensation.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package MSOP-10-EP
Category Power Management (PMIC)
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
反馈电压 TPS40211 (COMP=FB, TJ=25°C) VFB 254 260 266 mV COMP=FB, 4.5≤VDD≤52V, TJ=25°C 5
反馈电压 TPS40211 (全温度) VFB 250 260 270 mV COMP=FB, 4.5≤VDD≤52V, -40°C≤TJ≤125°C 5
VDD 输入电压范围 VDD 4.5 52 V 5
IDD 工作电流 IDD 1.5 2.5 mA 4.5≤VDD≤52V, 无开关, VDIS<0.8 5
IDD 工作电流 (使能电平) IDD 10 20 μA 2.5≤VDIS≤7V 5
IDD 工作电流 (VDD<UVLO) IDD 530 μA VDD<VUVLO(on), VDIS<0.8 5
欠压锁定导通阈值电压 VUVLO(on) 4 4.25 4.5 V 5
UVLO 迟滞 VUVLO(hyst) 140 195 240 mV 5
振荡器频率范围 fOSC 35 1000 kHz 5
振荡器频率 fOSC 260 300 340 kHz RRC=182kΩ, CRC=330pF 5
频率线性调整 -20 7 % 4.5≤VDD≤52V 5
斜率补偿斜坡 VSLP 520 620 720 mV 5
最小脉宽 tON(min) tON(min) 275 400 ns VDD = 12V 5
最小脉宽 tON(min) tON(min) 90 200 ns VDD = 30V 5
最短关断时间 tOFF(min) tOFF(min) 170 200 ns 5
软启动 RSS(chg) 充电电阻 RSS(chg) 320 430 600 kΩ 5
软启动 RSS(dchg) 放电电阻 RSS(dchg) 840 1200 1600 kΩ 5
单位增益带宽积 GBWP GBWP 1.5 3 MHz 5
开环增益 AOL AOL 60 80 dB 5
输入偏置电流 IIB(FB) IIB(FB) 100 300 nA 流出 FB 引脚的电流 5
输出拉电流 ICOMP(src) ICOMP(src) 100 250 μA VFB = 0.6V, VCOMP = 1V 5
输出灌电流 ICOMP(snk) ICOMP(snk) 1.2 2.5 mA VFB = 1.2V, VCOMP = 1V 5
过流检测阈值 (ISNS 引脚) VISNS(oc) 120 150 180 mV 4.5≤VDD<52V, -40°C≤TJ≤125°C 5
过流复位阈值电压 (SS 引脚) VSS(rst) 100 150 350 mV 5
电流检测放大器增益 ACS ACS 5.6 7.2 V/V 6
电流检测输入偏置电流 IB(ISNS) IB(ISNS) 1 3 μA 6
栅极驱动器拉电流 IGDRV(src) IGDRV(src) 375 400 mA VGDRV = 4V, TJ = 25°C 6
栅极驱动器灌电流 IGDRV(snk) IGDRV(snk) 330 400 mA VGDRV = 4V, TJ = 25°C 6
旁路电压输出 VBP VBP 7 8 9 V 0mA < IBP < 15mA 6
使能导通电压 VDIS(en) VDIS(en) 0.7 1.3 V 6
迟滞电压 VDIS(hys) VDIS(hys) 25 130 220 mV 6
DIS 引脚下拉电阻 RDIS RDIS 0.7 1.1 1.5 mΩ 6
过流占空比 DOC DOC 2 % 5
前缘消隐 TBLNK TBLNK 75 ns 5
软启动失调电压 VSS(ofst) VSS(ofst) 700 mV 从 SS 引脚到误差放大器输入端 5
谷值电压 VVLY VVLY 1.2 V 5
VDD 绝对最大输入电压 VDD -0.3 52 V 4
RC, SS, FB, DIS/EN 绝对最大电压 -0.3 10 V 4
ISNS 绝对最大电压 -0.3 8 V 4
COMP, BP, GDRV 绝对最大输出电压 -0.3 9 V 4
TJ 工作结温 (绝对最大) TJ -40 150 °C 4
贮存温度 Tstg Tstg -55 150 °C 4
VDD 输入电压 (推荐) VDD 4.5 52 V 4
TJ 工作结温 (推荐) TJ -40 125 °C 4
结至环境热阻 RθJA (HVSSOP 列) RθJA 67.2 °C/W HVSSOP 10 引脚 4
结至外壳(顶部)热阻 RθJC(top) (HVSSOP 列) RθJC(top) 50.5 °C/W HVSSOP 10 引脚 4
结至电路板热阻 RθJB (HVSSOP 列) RθJB 41 °C/W HVSSOP 10 引脚 4
结至顶部特征参数 ψJT (HVSSOP 列) ψJT 2.4 °C/W HVSSOP 10 引脚 4
结至电路板特征参数 ψJB (HVSSOP 列) ψJB 40.7 °C/W HVSSOP 10 引脚 4
结至外壳(底部)热阻 RθJC(bot) (HVSSOP 列) RθJC(bot) 15.6 °C/W HVSSOP 10 引脚 4

CAD (KiCad official)

  • Symbol: TPS40211DGQR
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: tps40211dgqr-etched.step / tps40211dgqr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps40211dgqr.step / tps40211dgqr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (50 pp, sha256 7213a870ac0ef0d9, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF