main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs tps25940aqrvctq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers tps25940aqrvctq1: viewers · Ray
package.json tps25940aqrvctq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
page.json tps25940aqrvctq1: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) · Ray
README.md Initial commit: component/tps25940aqrvctq1 · Ray
tps25940aqrvctq1-etched.fit.json tps25940aqrvctq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps25940aqrvctq1-etched.glb tps25940aqrvctq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps25940aqrvctq1-etched.step tps25940aqrvctq1: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
tps25940aqrvctq1.glb Publish 0.1.0 · Ray
tps25940aqrvctq1.kicad_mod Publish 0.1.0 · Ray
tps25940aqrvctq1.kicad_sym Publish 0.1.0 · Ray
tps25940aqrvctq1.lbr Publish 0.1.0 · Ray
tps25940aqrvctq1.step Publish 0.1.0 · Ray

TPS25940AQRVCTQ1

Texas Instruments · Surge Protection Devices (SPDs) · WQFN-20(4x3)

TPS25940AQRVCTQ1 from Texas Instruments, in a WQFN-20(4x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DEVSLP input Active-high DevSleep low-power mode control; rising threshold 1.6 V min / 1.85 V typ / 2.0 V max, falling 0.8 V min / 0.96 V typ / 1.1 V max; input leakage 0.6-1.25 µA; leave floating or connect to GND if unused.
2 PGOOD output Active-high open-drain power-good output; asserted high when PGTH > V(PGTHR) = 0.99 V (typ) and internal FET is fully enhanced; internal pull-down 10-35 Ω; max sink current 10 mA; leave floating if unused.
3 PGTH input Positive input of the internal power-good comparator; rising threshold V(PGTHR) = 0.97-1.01 V, falling V(PGTHF) = 0.90-0.94 V; leakage ±100 nA max; connect to OUT or GND if unused.
4 OUT power_out Switched power output; one of five paralleled OUT pins (4-8); total RON = 34-64 mΩ (-40 °C to +125 °C); max continuous switch current 4.78 A at TA = 85 °C; all OUT pins must be tied together and connected to the load.
5 OUT power_out Switched power output; paralleled with pins 4, 6, 7, 8; all OUT pins must be connected together and to the load.
6 OUT power_out Switched power output; paralleled with pins 4, 5, 7, 8; all OUT pins must be connected together and to the load.
7 OUT power_out Switched power output; paralleled with pins 4, 5, 6, 8; all OUT pins must be connected together and to the load.
8 OUT power_out Switched power output; paralleled with pins 4, 5, 6, 7; all OUT pins must be connected together and to the load.
9 IN power_in Power input and device supply voltage; operating range 2.7 V to 18 V (20 V abs max, 22 V for 10 ms transient); IQ(ON) = 140-270 µA; one of five paralleled IN pins (9-13); all IN pins must be connected together.
10 IN power_in Power input; paralleled with pins 9, 11, 12, 13; all IN pins must be connected together and to the power source.
11 IN power_in Power input; paralleled with pins 9, 10, 12, 13; all IN pins must be connected together and to the power source.
12 IN power_in Power input; paralleled with pins 9, 10, 11, 13; all IN pins must be connected together and to the power source.
13 IN power_in Power input; paralleled with pins 9, 10, 11, 12; all IN pins must be connected together and to the power source.
14 EN/UVLO input Enable and programmable undervoltage lockout input; FET turns off when V < V(ENF) = 0.92 V (typ); device enters low-IQ shutdown (IQ < 15 µA) when V < V(SHUTF) = 0.47 V (typ); pin must not be left floating; connect to IN if UVLO not needed.
15 OVP input Overvoltage protection threshold-setting input; FET opens and FLT asserts when V(OVP) > V(OVPR) = 0.99 V (typ); OVP disable delay 2 µs (typ); tie to GND when not used; leakage ±100 nA max.
16 GND power_in Ground reference for all voltages; must be connected to the exposed PowerPAD (pin 21); PowerPAD must be soldered to PCB ground plane with multiple vias for thermal performance; RθJCbot = 3.4 °C/W.
17 ILIM passive Current-limit programming pin; external resistor from ILIM to GND sets overload and short-circuit current limit via I(LIM) = 89 / R(ILIM); V(ILIM) bias = 0.87 V (typ); R(ILIM) range 16.9 kΩ to 150 kΩ corresponding to I(LIM) 5.3 A to 0.6 A (±8% accuracy).
18 dVdT passive Output voltage ramp-rate control pin; external capacitor from dVdT to GND sets output slew rate; I(dVdT) charging current = 1 µA (typ), V(dVdTmax) = 2.88 V (typ), GAIN(dVdT) = 11.9 V/V (typ); leave floating for internal 30 V/ms ramp; C(dVdT) up to 470 nF.
19 IMON output Analog current monitor output; sources a scaled current proportional to I(OUT) with GAIN(IMON) = 52.3 µA/A (typ), accuracy ±8% for TPS25940A-Q1; external resistor from IMON to GND converts to voltage; max output voltage min([V(IN) - 2.2 V], 6 V); leave floating if unused.
20 FLT output Active-low open-drain fault indicator; asserts low for undervoltage, overvoltage, reverse voltage (V(REVTH) = -66 mV typ), or thermal shutdown events; internal pull-down resistance 10-30 Ω; max sink current 10 mA; leave open or tie to GND if unused.
21 EP power_in Exposed PowerPAD (thermal pad); at GND potential; RθJCbot = 3.4 °C/W; must be soldered to PCB ground plane with multiple vias for optimal thermal and mechanical performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-20(4x3)
Category Circuit Protection
Pins 21

CAD (KiCad official)

  • Symbol: TPS25940AQRVCTQ1
  • Footprint: Package_DFN_QFN:QFN-20-1EP_3x4mm_P0.5mm_EP1.65x2.65mm
  • 3D model: WQFN-20(4x3) (KiCad packages3D, STEP)
  • 3D model files: tps25940aqrvctq1-etched.step / tps25940aqrvctq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps25940aqrvctq1.step / tps25940aqrvctq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (51 pp, sha256 a1b7de698cb52759, retrieved 2026-09-26, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-4-6 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF