main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers tps24772rger: viewers rendered from the public page · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
tps24772rger-etched.glb Publish 0.1.0 · Ray
tps24772rger-etched.step tps24772rger: factory component page (tier=mfr) · Ray
tps24772rger-hero.glb tps24772rger: hero GLB from the etched model (keeps the MPN mark) · Ray
tps24772rger-hero.overlay.json Publish 0.1.0 · Ray
tps24772rger.glb Publish 0.1.0 · Ray
tps24772rger.kicad_mod Publish 0.1.0 · Ray
tps24772rger.kicad_sym Publish 0.1.0 · Ray
tps24772rger.lbr Publish 0.1.0 · Ray
tps24772rger.step Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 25 pins · Ray

TPS24772RGER

Texas Instruments · Supervisor And Reset ICs · VQFN-24-EP(4x4)

TPS24772RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect. Tie to ground or leave floating.
2 ENHS input Active-high Hot Swap enable input; the part turns on when the pin rises above 1.35 V and turns off below 1.3 V (50 mV hysteresis), and it connects to a resistor divider.
3 NC unconnected No connect. Tie to ground or leave floating.
4 FLTb output Active-low open-drain fault output asserted for a Hot Swap MOSFET short, a fault-timer timeout, or over-temperature shutdown; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum).
5 PGHS output Active-high open-drain power-good output; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum).
6 NC unconnected No connect. Tie to ground or leave floating.
7 TINR bidirectional Inrush timer, which runs during start-up when the part is in current or power limit; the timer times out when the pin exceeds 1.35 V.
8 TFLT bidirectional Fault timer, which runs during regular operation when an overcurrent condition exists; the timer times out when the pin exceeds 1.35 V.
9 OV input Overvoltage comparator input with a 1.35 V rising threshold that connects to a resistor divider; HGATE is pulled low when OV exceeds the threshold, and it should be tied to ground when not used.
10 GND power_in Ground.
11 PLIM input Power-limit programming pin; a resistor from this pin to GND sets the maximum Hot Swap FET power dissipation, with a recommended range of 4.99 kΩ to 500 kΩ (4.99 kΩ disables power limit).
12 IMON bidirectional Analog monitor and current-limit programming point; RIMON connects to ground, the recommended resistance is 1 kΩ to 6 kΩ, and the pin supports up to 30 pF of capacitance.
13 IMONBUF output Buffered voltage output proportional to load current, with a 0 V to 3.0 V range; it can drive up to 100 pF of capacitance.
14 VDD power_in Power supply; recommended operating range is 2.5 V to 18 V, with a 30 V absolute maximum.
15 SET input Current-limit programming pin; a resistor from the positive terminal of the sense resistor to SET sets the current limit, with a recommended external resistance of 10 Ω to 400 Ω.
16 FSTP input Fast-trip threshold programming pin; a resistor from the positive terminal of RSNS to FSTP sets the fast-trip threshold, with a recommended external resistance of 10 Ω to 4000 Ω.
17 SENM input Current-sense input connected directly to the negative terminal of the sense resistor; recommended operating voltage is 2.5 V to 18 V.
18 HGATE output Gate driver output for the external Hot Swap MOSFET; HGATE-to-OUTH must stay within the 15 V absolute maximum.
19 OUTH input Output voltage sensor that connects to the source terminal of the Hot Swap N-channel MOSFET to monitor its power; recommended operating range is 0 V to 18 V.
20 NC unconnected No connect. Tie to ground or leave floating.
21 NC unconnected No connect. Tie to ground or leave floating.
22 NC unconnected No connect. Tie to ground or leave floating.
23 NC unconnected No connect. Tie to ground or leave floating.
24 NC unconnected No connect. Tie to ground or leave floating.
25 Thermal pad passive Exposed thermal pad that must be soldered to the printed circuit board for thermal and mechanical performance; the datasheet does not state an electrical connection for it.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-24-EP(4x4)
Category Power Management (PMIC)
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage, VDD, SET, FSTP, SENM, OUTH, ENHS, FLTb, PGHS, OV -0.3 30 V 4
HGATE to OUTH input voltage -0.3 15 V 4
SET to VDD input voltage -0.3 0.3 V 4
SENM, FSTP to VDD input voltage -0.6 0.3 V 4
TINR, TFLT, PLIM, IMON input voltage -0.3 3.6 V 4
IMONBUF input voltage -0.3 7 V 4
Sink current FLTb, PGHS 5 mA 4
Source current IMON, IMONBUF 5 mA 4
Storage temperature Tstg -65 150 °C 4
Input voltage VDD, SENM, SET, FSTP 2.5 18 V 5
Input voltage ENHS, FLTb, PGHS, OUTH 0 18 V 5
Sink current FLTb, PGHS 0 2 mA 5
Source current IMON 0 1 mA 5
External resistance PLIM 4.99 500 kΩ 5
External resistance IMON 1 6 kΩ 5
External resistance FSTP 10 4000 Ω 5
External resistance SET 10 400 Ω 5
External resistance RIMON / RSET 10 70 Ω w/o RSTBL 5
External resistance RIMON / RSET 3 10 Ω With appropriate RSTBL (note 1) 5
External capacitor TINR, TFLT 1 nF 5
External capacitor HGATE 0 1 µF In series with resistor ≥1 kΩ (note 2) 5
External capacitor IMON 30 pF 5
External capacitor IMONBUF 100 pF 5
Operating junction temperature TJ -40 125 °C 5
UVLO threshold, rising VUVR 2.2 2.32 2.45 V 5
Supply current IVDD + IOUTH IQON 2.95 4 mA Device on, VENHS = 2V 5
Hot Swap FET enable threshold voltage, rising VENHS 1.3 1.35 1.4 V 5
Over voltage threshold voltage, rising VOVR 1.3 1.35 1.4 mV 5
Power limit bias voltage VPLIM,BIAS 0.65 0.675 0.7 V Sourcing 10μA 6
Regulated IMON voltage during power limit VIMON,PL 114.75 135 155.25 mV RPLIM = 52 kΩ; VSENM-OUTH=12V 6
Regulated IMON voltage during power limit VIMON,PL 56.95 67 77.05 mV RPLIM = 105 kΩ; VSENM-OUTH=12V 6
Regulated IMON voltage during power limit VIMON,PL 18.9 27 35.1 mV RPLIM = 261 kΩ; VSENM-OUTH=12V 6
Input referred offset (VSNS to VIMON scaling) VOS_SET -150 150 µV SET = 44.2Ω; RIMON=3kΩ to 1.2kΩ (VSNS,CL=10mV to 25mV) 6
Gain error (VSNS to VIMON scaling) GE_SET -0.4 0.4 % 6
FSTP input bias current IFSTP 95 100 105 µA VFSTP=12V 6
Fast trip threshold VFASTRIP 18 20 22 mV RFSTP = 200 Ω, VSNS when VHGATE ↓ 6
Slow trip threshold at summing node VIMON,CL 660 675 690 mV VIMON↑, when ITFLT starts sourcing 6
Buffer offset VOS_IMONBUF -3 0 3 mV VIMON = 50mV to 675mV, Input referred 6
Buffer voltage gain GAINIMONBUF 2.97 2.99 3.01 V 6
HGATE output voltage VHGATE 12 13.6 15.5 V 5 ≤ VVDD ≤ 16V; measure VHGATE-OUTH 6
HGATE sourcing current IHGATEsrc 44 55 66 µA VHGATE-OUTH = 2V-10V 6
HGATE sinking current for fast trip IHGATEfastSink 0.45 1 1.6 A VHGATE-OUTH = 2V-15V; V(FSTP, SENM) = 20mV 6
TINR sourcing current ITINRsrc 8 10.25 12.5 µA VTINR = 0V, In power limit or current limit 6
TINR sinking current ITINRsink 1.5 2 2.5 µA VTINR = 2V, In regular operation 6
TINR upper threshold voltage VTINRup 1.3 1.35 1.4 V Raise VTINR until HGATE starts sinking 6
TINR lower threshold voltage VTINRlr 0.33 0.35 0.37 v Raise VTINR to 2V. Reduce VTINR until ITINR is sourcing. 6
IMON voltage when TINR starts sourcing current VIMON,TINR 47.75 90 132.25 mV RPLIM = 52kΩ, VSENM = 12V, VOUTH = 0 V 6
IMON voltage when IHGATE starts sinking current VIMON,PL 114.75 135 155.25 mV RPLIM = 52kΩ, VSENM-OUTH = 12V 6
Fault timer sourcing current ITFLTsrc 8 10.25 12.5 µA VTFLT = 0V, PGHS is high and in overcurrent 7
Fault timer sinking current ITFLTsink 1.5 2 2.5 µA VTFLT = 2V, Not in overcurrent 7
Fault timer upper threshold voltage VTFLTup 1.3 1.35 1.4 V Raise VTFLT until HGATE starts sinking 7
VIMON threshold to detect Hot Swap FET short VHSFLT_IMON 88 101 115 mV VENHS = 0V, Measured VIMON ↑ to GND when FLTb ↓ 7
PGHS threshold VPGHSth 170 270 375 mV Measure VSENM-OUTH ↓ when PGHS↑ 7
PGHS output low voltage VOL_PGHS 0.11 0.25 V Sinking 2mA 7
FLTb output low voltage VOL_FLTb 0.11 0.25 V Sinking 2 mA 7
Hot Swap FET enable deglitch time DEGLENHS 2.2 3.8 5.5 µs Both rising and falling 7
Over voltage deglitch time DEGLOV 2.2 3.9 5.7 µs Both rising and falling 7
Strong pull down current duration tFastOffDur 53 63 73 µs 7
Fault deglitch time tFLT_degl 2.2 3.9 5.3 ms Both rising and falling 7
PGHS deglitch time, rising tPGHSdegl 0.7 1 1.3 ms Rising 7

CAD (KiCad official)

  • Symbol: TPS24772RGER
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: tps24772rger-etched.step / tps24772rger-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tps24772rger.step / tps24772rger.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (52 pp, sha256 37f953f4e5224b99, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF