main
Ray
Publish 0.1.0
d9d3f90
TPS24772RGER
Texas Instruments · Supervisor And Reset ICs · VQFN-24-EP(4x4)
TPS24772RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 2 | ENHS | input | Active-high Hot Swap enable input; the part turns on when the pin rises above 1.35 V and turns off below 1.3 V (50 mV hysteresis), and it connects to a resistor divider. |
| 3 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 4 | FLTb | output | Active-low open-drain fault output asserted for a Hot Swap MOSFET short, a fault-timer timeout, or over-temperature shutdown; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum). |
| 5 | PGHS | output | Active-high open-drain power-good output; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum). |
| 6 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 7 | TINR | bidirectional | Inrush timer, which runs during start-up when the part is in current or power limit; the timer times out when the pin exceeds 1.35 V. |
| 8 | TFLT | bidirectional | Fault timer, which runs during regular operation when an overcurrent condition exists; the timer times out when the pin exceeds 1.35 V. |
| 9 | OV | input | Overvoltage comparator input with a 1.35 V rising threshold that connects to a resistor divider; HGATE is pulled low when OV exceeds the threshold, and it should be tied to ground when not used. |
| 10 | GND | power_in | Ground. |
| 11 | PLIM | input | Power-limit programming pin; a resistor from this pin to GND sets the maximum Hot Swap FET power dissipation, with a recommended range of 4.99 kΩ to 500 kΩ (4.99 kΩ disables power limit). |
| 12 | IMON | bidirectional | Analog monitor and current-limit programming point; RIMON connects to ground, the recommended resistance is 1 kΩ to 6 kΩ, and the pin supports up to 30 pF of capacitance. |
| 13 | IMONBUF | output | Buffered voltage output proportional to load current, with a 0 V to 3.0 V range; it can drive up to 100 pF of capacitance. |
| 14 | VDD | power_in | Power supply; recommended operating range is 2.5 V to 18 V, with a 30 V absolute maximum. |
| 15 | SET | input | Current-limit programming pin; a resistor from the positive terminal of the sense resistor to SET sets the current limit, with a recommended external resistance of 10 Ω to 400 Ω. |
| 16 | FSTP | input | Fast-trip threshold programming pin; a resistor from the positive terminal of RSNS to FSTP sets the fast-trip threshold, with a recommended external resistance of 10 Ω to 4000 Ω. |
| 17 | SENM | input | Current-sense input connected directly to the negative terminal of the sense resistor; recommended operating voltage is 2.5 V to 18 V. |
| 18 | HGATE | output | Gate driver output for the external Hot Swap MOSFET; HGATE-to-OUTH must stay within the 15 V absolute maximum. |
| 19 | OUTH | input | Output voltage sensor that connects to the source terminal of the Hot Swap N-channel MOSFET to monitor its power; recommended operating range is 0 V to 18 V. |
| 20 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 21 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 22 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 23 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 24 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 25 | Thermal pad | passive | Exposed thermal pad that must be soldered to the printed circuit board for thermal and mechanical performance; the datasheet does not state an electrical connection for it. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage, VDD, SET, FSTP, SENM, OUTH, ENHS, FLTb, PGHS, OV | -0.3 | 30 | V | 4 | |||
| HGATE to OUTH input voltage | -0.3 | 15 | V | 4 | |||
| SET to VDD input voltage | -0.3 | 0.3 | V | 4 | |||
| SENM, FSTP to VDD input voltage | -0.6 | 0.3 | V | 4 | |||
| TINR, TFLT, PLIM, IMON input voltage | -0.3 | 3.6 | V | 4 | |||
| IMONBUF input voltage | -0.3 | 7 | V | 4 | |||
| Sink current FLTb, PGHS | 5 | mA | 4 | ||||
| Source current IMON, IMONBUF | 5 | mA | 4 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Input voltage VDD, SENM, SET, FSTP | 2.5 | 18 | V | 5 | |||
| Input voltage ENHS, FLTb, PGHS, OUTH | 0 | 18 | V | 5 | |||
| Sink current FLTb, PGHS | 0 | 2 | mA | 5 | |||
| Source current IMON | 0 | 1 | mA | 5 | |||
| External resistance PLIM | 4.99 | 500 | kΩ | 5 | |||
| External resistance IMON | 1 | 6 | kΩ | 5 | |||
| External resistance FSTP | 10 | 4000 | Ω | 5 | |||
| External resistance SET | 10 | 400 | Ω | 5 | |||
| External resistance RIMON / RSET | 10 | 70 | Ω | w/o RSTBL | 5 | ||
| External resistance RIMON / RSET | 3 | 10 | Ω | With appropriate RSTBL (note 1) | 5 | ||
| External capacitor TINR, TFLT | 1 | nF | 5 | ||||
| External capacitor HGATE | 0 | 1 | µF | In series with resistor ≥1 kΩ (note 2) | 5 | ||
| External capacitor IMON | 30 | pF | 5 | ||||
| External capacitor IMONBUF | 100 | pF | 5 | ||||
| Operating junction temperature | TJ | -40 | 125 | °C | 5 | ||
| UVLO threshold, rising | VUVR | 2.2 | 2.32 | 2.45 | V | 5 | |
| Supply current IVDD + IOUTH | IQON | 2.95 | 4 | mA | Device on, VENHS = 2V | 5 | |
| Hot Swap FET enable threshold voltage, rising | VENHS | 1.3 | 1.35 | 1.4 | V | 5 | |
| Over voltage threshold voltage, rising | VOVR | 1.3 | 1.35 | 1.4 | mV | 5 | |
| Power limit bias voltage | VPLIM,BIAS | 0.65 | 0.675 | 0.7 | V | Sourcing 10μA | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 114.75 | 135 | 155.25 | mV | RPLIM = 52 kΩ; VSENM-OUTH=12V | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 56.95 | 67 | 77.05 | mV | RPLIM = 105 kΩ; VSENM-OUTH=12V | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 18.9 | 27 | 35.1 | mV | RPLIM = 261 kΩ; VSENM-OUTH=12V | 6 |
| Input referred offset (VSNS to VIMON scaling) | VOS_SET | -150 | 150 | µV | SET = 44.2Ω; RIMON=3kΩ to 1.2kΩ (VSNS,CL=10mV to 25mV) | 6 | |
| Gain error (VSNS to VIMON scaling) | GE_SET | -0.4 | 0.4 | % | 6 | ||
| FSTP input bias current | IFSTP | 95 | 100 | 105 | µA | VFSTP=12V | 6 |
| Fast trip threshold | VFASTRIP | 18 | 20 | 22 | mV | RFSTP = 200 Ω, VSNS when VHGATE ↓ | 6 |
| Slow trip threshold at summing node | VIMON,CL | 660 | 675 | 690 | mV | VIMON↑, when ITFLT starts sourcing | 6 |
| Buffer offset | VOS_IMONBUF | -3 | 0 | 3 | mV | VIMON = 50mV to 675mV, Input referred | 6 |
| Buffer voltage gain | GAINIMONBUF | 2.97 | 2.99 | 3.01 | V | 6 | |
| HGATE output voltage | VHGATE | 12 | 13.6 | 15.5 | V | 5 ≤ VVDD ≤ 16V; measure VHGATE-OUTH | 6 |
| HGATE sourcing current | IHGATEsrc | 44 | 55 | 66 | µA | VHGATE-OUTH = 2V-10V | 6 |
| HGATE sinking current for fast trip | IHGATEfastSink | 0.45 | 1 | 1.6 | A | VHGATE-OUTH = 2V-15V; V(FSTP, SENM) = 20mV | 6 |
| TINR sourcing current | ITINRsrc | 8 | 10.25 | 12.5 | µA | VTINR = 0V, In power limit or current limit | 6 |
| TINR sinking current | ITINRsink | 1.5 | 2 | 2.5 | µA | VTINR = 2V, In regular operation | 6 |
| TINR upper threshold voltage | VTINRup | 1.3 | 1.35 | 1.4 | V | Raise VTINR until HGATE starts sinking | 6 |
| TINR lower threshold voltage | VTINRlr | 0.33 | 0.35 | 0.37 | v | Raise VTINR to 2V. Reduce VTINR until ITINR is sourcing. | 6 |
| IMON voltage when TINR starts sourcing current | VIMON,TINR | 47.75 | 90 | 132.25 | mV | RPLIM = 52kΩ, VSENM = 12V, VOUTH = 0 V | 6 |
| IMON voltage when IHGATE starts sinking current | VIMON,PL | 114.75 | 135 | 155.25 | mV | RPLIM = 52kΩ, VSENM-OUTH = 12V | 6 |
| Fault timer sourcing current | ITFLTsrc | 8 | 10.25 | 12.5 | µA | VTFLT = 0V, PGHS is high and in overcurrent | 7 |
| Fault timer sinking current | ITFLTsink | 1.5 | 2 | 2.5 | µA | VTFLT = 2V, Not in overcurrent | 7 |
| Fault timer upper threshold voltage | VTFLTup | 1.3 | 1.35 | 1.4 | V | Raise VTFLT until HGATE starts sinking | 7 |
| VIMON threshold to detect Hot Swap FET short | VHSFLT_IMON | 88 | 101 | 115 | mV | VENHS = 0V, Measured VIMON ↑ to GND when FLTb ↓ | 7 |
| PGHS threshold | VPGHSth | 170 | 270 | 375 | mV | Measure VSENM-OUTH ↓ when PGHS↑ | 7 |
| PGHS output low voltage | VOL_PGHS | 0.11 | 0.25 | V | Sinking 2mA | 7 | |
| FLTb output low voltage | VOL_FLTb | 0.11 | 0.25 | V | Sinking 2 mA | 7 | |
| Hot Swap FET enable deglitch time | DEGLENHS | 2.2 | 3.8 | 5.5 | µs | Both rising and falling | 7 |
| Over voltage deglitch time | DEGLOV | 2.2 | 3.9 | 5.7 | µs | Both rising and falling | 7 |
| Strong pull down current duration | tFastOffDur | 53 | 63 | 73 | µs | 7 | |
| Fault deglitch time | tFLT_degl | 2.2 | 3.9 | 5.3 | ms | Both rising and falling | 7 |
| PGHS deglitch time, rising | tPGHSdegl | 0.7 | 1 | 1.3 | ms | Rising | 7 |
CAD (KiCad official)
- Symbol:
TPS24772RGER - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
tps24772rger-etched.step/tps24772rger-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps24772rger.step/tps24772rger.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (52 pp, sha256
37f953f4e5224b99, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TPS24772RGER
**Texas Instruments** · Supervisor And Reset ICs · VQFN-24-EP(4x4)
TPS24772RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 2 | ENHS | input | Active-high Hot Swap enable input; the part turns on when the pin rises above 1.35 V and turns off below 1.3 V (50 mV hysteresis), and it connects to a resistor divider. |
| 3 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 4 | FLTb | output | Active-low open-drain fault output asserted for a Hot Swap MOSFET short, a fault-timer timeout, or over-temperature shutdown; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum). |
| 5 | PGHS | output | Active-high open-drain power-good output; sink current is limited to 2 mA in recommended operation (5 mA absolute maximum). |
| 6 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 7 | TINR | bidirectional | Inrush timer, which runs during start-up when the part is in current or power limit; the timer times out when the pin exceeds 1.35 V. |
| 8 | TFLT | bidirectional | Fault timer, which runs during regular operation when an overcurrent condition exists; the timer times out when the pin exceeds 1.35 V. |
| 9 | OV | input | Overvoltage comparator input with a 1.35 V rising threshold that connects to a resistor divider; HGATE is pulled low when OV exceeds the threshold, and it should be tied to ground when not used. |
| 10 | GND | power_in | Ground. |
| 11 | PLIM | input | Power-limit programming pin; a resistor from this pin to GND sets the maximum Hot Swap FET power dissipation, with a recommended range of 4.99 kΩ to 500 kΩ (4.99 kΩ disables power limit). |
| 12 | IMON | bidirectional | Analog monitor and current-limit programming point; RIMON connects to ground, the recommended resistance is 1 kΩ to 6 kΩ, and the pin supports up to 30 pF of capacitance. |
| 13 | IMONBUF | output | Buffered voltage output proportional to load current, with a 0 V to 3.0 V range; it can drive up to 100 pF of capacitance. |
| 14 | VDD | power_in | Power supply; recommended operating range is 2.5 V to 18 V, with a 30 V absolute maximum. |
| 15 | SET | input | Current-limit programming pin; a resistor from the positive terminal of the sense resistor to SET sets the current limit, with a recommended external resistance of 10 Ω to 400 Ω. |
| 16 | FSTP | input | Fast-trip threshold programming pin; a resistor from the positive terminal of RSNS to FSTP sets the fast-trip threshold, with a recommended external resistance of 10 Ω to 4000 Ω. |
| 17 | SENM | input | Current-sense input connected directly to the negative terminal of the sense resistor; recommended operating voltage is 2.5 V to 18 V. |
| 18 | HGATE | output | Gate driver output for the external Hot Swap MOSFET; HGATE-to-OUTH must stay within the 15 V absolute maximum. |
| 19 | OUTH | input | Output voltage sensor that connects to the source terminal of the Hot Swap N-channel MOSFET to monitor its power; recommended operating range is 0 V to 18 V. |
| 20 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 21 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 22 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 23 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 24 | NC | unconnected | No connect. Tie to ground or leave floating. |
| 25 | Thermal pad | passive | Exposed thermal pad that must be soldered to the printed circuit board for thermal and mechanical performance; the datasheet does not state an electrical connection for it. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | Power Management (PMIC) |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage, VDD, SET, FSTP, SENM, OUTH, ENHS, FLTb, PGHS, OV | | -0.3 | | 30 | V | | 4 |
| HGATE to OUTH input voltage | | -0.3 | | 15 | V | | 4 |
| SET to VDD input voltage | | -0.3 | | 0.3 | V | | 4 |
| SENM, FSTP to VDD input voltage | | -0.6 | | 0.3 | V | | 4 |
| TINR, TFLT, PLIM, IMON input voltage | | -0.3 | | 3.6 | V | | 4 |
| IMONBUF input voltage | | -0.3 | | 7 | V | | 4 |
| Sink current FLTb, PGHS | | | | 5 | mA | | 4 |
| Source current IMON, IMONBUF | | | | 5 | mA | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| Input voltage VDD, SENM, SET, FSTP | | 2.5 | | 18 | V | | 5 |
| Input voltage ENHS, FLTb, PGHS, OUTH | | 0 | | 18 | V | | 5 |
| Sink current FLTb, PGHS | | 0 | | 2 | mA | | 5 |
| Source current IMON | | 0 | | 1 | mA | | 5 |
| External resistance PLIM | | 4.99 | | 500 | kΩ | | 5 |
| External resistance IMON | | 1 | | 6 | kΩ | | 5 |
| External resistance FSTP | | 10 | | 4000 | Ω | | 5 |
| External resistance SET | | 10 | | 400 | Ω | | 5 |
| External resistance RIMON / RSET | | 10 | | 70 | Ω | w/o RSTBL | 5 |
| External resistance RIMON / RSET | | 3 | | 10 | Ω | With appropriate RSTBL (note 1) | 5 |
| External capacitor TINR, TFLT | | 1 | | | nF | | 5 |
| External capacitor HGATE | | 0 | | 1 | µF | In series with resistor ≥1 kΩ (note 2) | 5 |
| External capacitor IMON | | | | 30 | pF | | 5 |
| External capacitor IMONBUF | | | | 100 | pF | | 5 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 5 |
| UVLO threshold, rising | VUVR | 2.2 | 2.32 | 2.45 | V | | 5 |
| Supply current IVDD + IOUTH | IQON | | 2.95 | 4 | mA | Device on, VENHS = 2V | 5 |
| Hot Swap FET enable threshold voltage, rising | VENHS | 1.3 | 1.35 | 1.4 | V | | 5 |
| Over voltage threshold voltage, rising | VOVR | 1.3 | 1.35 | 1.4 | mV | | 5 |
| Power limit bias voltage | VPLIM,BIAS | 0.65 | 0.675 | 0.7 | V | Sourcing 10μA | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 114.75 | 135 | 155.25 | mV | RPLIM = 52 kΩ; VSENM-OUTH=12V | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 56.95 | 67 | 77.05 | mV | RPLIM = 105 kΩ; VSENM-OUTH=12V | 6 |
| Regulated IMON voltage during power limit | VIMON,PL | 18.9 | 27 | 35.1 | mV | RPLIM = 261 kΩ; VSENM-OUTH=12V | 6 |
| Input referred offset (VSNS to VIMON scaling) | VOS_SET | -150 | | 150 | µV | SET = 44.2Ω; RIMON=3kΩ to 1.2kΩ (VSNS,CL=10mV to 25mV) | 6 |
| Gain error (VSNS to VIMON scaling) | GE_SET | -0.4 | | 0.4 | % | | 6 |
| FSTP input bias current | IFSTP | 95 | 100 | 105 | µA | VFSTP=12V | 6 |
| Fast trip threshold | VFASTRIP | 18 | 20 | 22 | mV | RFSTP = 200 Ω, VSNS when VHGATE ↓ | 6 |
| Slow trip threshold at summing node | VIMON,CL | 660 | 675 | 690 | mV | VIMON↑, when ITFLT starts sourcing | 6 |
| Buffer offset | VOS_IMONBUF | -3 | 0 | 3 | mV | VIMON = 50mV to 675mV, Input referred | 6 |
| Buffer voltage gain | GAINIMONBUF | 2.97 | 2.99 | 3.01 | V | | 6 |
| HGATE output voltage | VHGATE | 12 | 13.6 | 15.5 | V | 5 ≤ VVDD ≤ 16V; measure VHGATE-OUTH | 6 |
| HGATE sourcing current | IHGATEsrc | 44 | 55 | 66 | µA | VHGATE-OUTH = 2V-10V | 6 |
| HGATE sinking current for fast trip | IHGATEfastSink | 0.45 | 1 | 1.6 | A | VHGATE-OUTH = 2V-15V; V(FSTP, SENM) = 20mV | 6 |
| TINR sourcing current | ITINRsrc | 8 | 10.25 | 12.5 | µA | VTINR = 0V, In power limit or current limit | 6 |
| TINR sinking current | ITINRsink | 1.5 | 2 | 2.5 | µA | VTINR = 2V, In regular operation | 6 |
| TINR upper threshold voltage | VTINRup | 1.3 | 1.35 | 1.4 | V | Raise VTINR until HGATE starts sinking | 6 |
| TINR lower threshold voltage | VTINRlr | 0.33 | 0.35 | 0.37 | v | Raise VTINR to 2V. Reduce VTINR until ITINR is sourcing. | 6 |
| IMON voltage when TINR starts sourcing current | VIMON,TINR | 47.75 | 90 | 132.25 | mV | RPLIM = 52kΩ, VSENM = 12V, VOUTH = 0 V | 6 |
| IMON voltage when IHGATE starts sinking current | VIMON,PL | 114.75 | 135 | 155.25 | mV | RPLIM = 52kΩ, VSENM-OUTH = 12V | 6 |
| Fault timer sourcing current | ITFLTsrc | 8 | 10.25 | 12.5 | µA | VTFLT = 0V, PGHS is high and in overcurrent | 7 |
| Fault timer sinking current | ITFLTsink | 1.5 | 2 | 2.5 | µA | VTFLT = 2V, Not in overcurrent | 7 |
| Fault timer upper threshold voltage | VTFLTup | 1.3 | 1.35 | 1.4 | V | Raise VTFLT until HGATE starts sinking | 7 |
| VIMON threshold to detect Hot Swap FET short | VHSFLT_IMON | 88 | 101 | 115 | mV | VENHS = 0V, Measured VIMON ↑ to GND when FLTb ↓ | 7 |
| PGHS threshold | VPGHSth | 170 | 270 | 375 | mV | Measure VSENM-OUTH ↓ when PGHS↑ | 7 |
| PGHS output low voltage | VOL_PGHS | | 0.11 | 0.25 | V | Sinking 2mA | 7 |
| FLTb output low voltage | VOL_FLTb | | 0.11 | 0.25 | V | Sinking 2 mA | 7 |
| Hot Swap FET enable deglitch time | DEGLENHS | 2.2 | 3.8 | 5.5 | µs | Both rising and falling | 7 |
| Over voltage deglitch time | DEGLOV | 2.2 | 3.9 | 5.7 | µs | Both rising and falling | 7 |
| Strong pull down current duration | tFastOffDur | 53 | 63 | 73 | µs | | 7 |
| Fault deglitch time | tFLT_degl | 2.2 | 3.9 | 5.3 | ms | Both rising and falling | 7 |
| PGHS deglitch time, rising | tPGHSdegl | 0.7 | 1 | 1.3 | ms | Rising | 7 |
## CAD (KiCad official)
- Symbol: `TPS24772RGER`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `tps24772rger-etched.step` / `tps24772rger-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps24772rger.step` / `tps24772rger.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps24772.pdf) (52 pp, sha256 `37f953f4e5224b99`, retrieved 2026-11-10, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/tps24772rger-datasheet.pdf)