Generated by kicad-footprint-generator · KiCad file format 20260206
TP4066-4.2V-DFN228
TOPPOWER(Nanjing Extension Microelectronics) · Battery Management · DFN-8-EP(2x2)
TP4066-4.2V-DFN228 from TOPPOWER(Nanjing Extension Microelectronics), in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TEMP | input | Temperature sense input connected to the battery NTC; charging is suspended if TEMP is below 45% or above 80% of VIN, and the function is disabled by grounding TEMP. |
| 2 | PROG | passive | Sets the constant charge current via a resistor RPROG to GND, with the pin regulated to 1V in constant current mode and 0.2V in precharge mode. |
| 3 | GND | power_in | Ground terminal. |
| 4 | VCC | power_in | Positive input supply voltage; the operating range is 4.35V to 12.0V, and the chip enters sleep mode when VCC drops to within 50mV of the BAT pin voltage. |
| 5 | BAT | power_out | Battery connection that supplies charge current to the battery and provides the 4.2V regulation voltage; it draws less than 1uA in shutdown or sleep mode. |
| 6 | STDBY | output | Open-drain charge termination status output that is pulled low when charging is terminated and is otherwise high impedance. |
| 7 | CHRG | output | Open-drain charge status output that is pulled low while the battery is being charged and is otherwise high impedance. |
| 8 | CE | input | Chip enable input where a high level enables normal operation and a low level puts the device into disable mode; it can be driven by TTL or CMOS logic levels. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TOPPOWER(Nanjing Extension Microelectronics) |
| Package | DFN-8-EP(2x2) |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Supply Voltage | VCC | 4.35 | 5 | 12 | V | ● full operating temperature range | 3 |
| Overvoltage protection point | VOVP | 6.5 | 7 | 7.5 | V | ● full operating temperature range | 3 |
| Regulated Output (Float) Voltage 4.2V | VFLOAT | 4.158 | 4.2 | 4.242 | V | 0℃≤TA≤85℃ | 3 |
| Charge current RPROG=1.2K | IBAT | 442 | 520 | 598 | mA | RPROG=1.2K, Current Mode | 3 |
| Charge current RPROG=0.7K | IBAT | 850 | 1000 | 1150 | mA | RPROG=0.7K, Current Mode | 3 |
| Trickle Charge Current | ITRIKL | 90 | 130 | 170 | mA | VBAT<VTRIKL, RPROG=0.7K | 3 |
| Trickle Charge Threshold Voltage | VTRIKL | 2.8 | 2.9 | 3 | V | RPROG=0.7K, VBAT Rising | 3 |
| Trickle Charge Hysteresis Voltage | VTRHYS | 60 | 80 | 100 | mV | RPROG=0.7K | 3 |
| VCC UVLO Voltage | VUV | 3.5 | 3.7 | 3.9 | V | VCC from low to high | 3 |
| VCC UVLO Hysteresis | VUVHYS | 150 | 200 | 300 | mV | ● | 3 |
| VCC-VBAT lockout threshold voltage (rising) | VASD | 130 | 160 | 190 | mV | VCC from low to high | 3 |
| VCC-VBAT lockout threshold voltage (falling) | VASD | 30 | 50 | 70 | mV | VCC from high to low | 3 |
| C/10 termination current threshold RPROG=1.2K | ITERM | 30 | 45 | 60 | mA | RPROG=1.2K | 3 |
| C/10 termination current threshold RPROG=0.7K | ITERM | 60 | 100 | 140 | mA | RPROG=0.7K | 3 |
| PROG pin voltage | VPROG | 0.9 | 1 | 1.1 | V | RPROG=0.7K, current mode | 3 |
| CHRG pin output low voltage | 0.2 | 0.6 | V | I=20mA | 3 | ||
| STDBY pin output low voltage | 0.2 | 0.6 | V | I=20mA | 3 | ||
| TEMP upper trip threshold | VTEMP-H | 80 | 82 | %Vcc | 3 | ||
| TEMP lower trip threshold | VTEMP-L | 43 | 45 | %Vcc | 3 | ||
| Recharge battery threshold voltage | ΔVRECHRG | 90 | 110 | 130 | mV | VFLOAL=4.2V | 3 |
| Recharge comparator filter time | tRECHARGE | 0.8 | 1.8 | 4 | ms | VBAT from high to low | 4 |
| Termination comparator filter time | tTERM | 0.8 | 1.8 | 4 | ms | IBAT drops below ICHG/10 | 4 |
| Vcc adaptive starting voltage | VADPT | 4.1 | 4.3 | 4.5 | V | Rprog=0.7K, Vcc from high to low | 4 |
| BAT reverse leakage current | IBAT | 25 | 30 | mA | BAT reverse, VIN =5V | 4 | |
| Input Supply Current Charge Mode | ICC | 120 | 200 | μA | Charge Mode, RPROG = 0.7K, ● | 3 | |
| Input Supply Current Standby Mode (Charge Terminated) | ICC | 90 | 200 | μA | Standby Mode (Charge Terminated), ● | 3 | |
| Input Supply Current Shutdown Mode | ICC | 90 | 200 | μA | Shutdown Mode (RPROG Not Connected, VCC < VBAT, or VCC < VUV), ● | 3 | |
| Junction Temperature in Constant Temperature Mode | TLIM | 145 | ℃ | 3 | |||
| The resistance of power FET ON (between VCC and BAT) | RON | 400 | mΩ | 3 | |||
| Soft-start time | tss | 20 | us | IBAT=0 to IBAT=1100V/RPROG | 4 | ||
| PROG pin pull-up current | IPROG | 2 | μA | 4 | |||
| Input Supply Voltage absolute maximum | VCC | -0.3 | 12 | V | 1 | ||
| PROG pin voltage absolute maximum | PROG | -0.3 | V | VCC+0.3V | 1 | ||
| BAT pin voltage absolute maximum | BAT | -4.35 | 7 | V | 1 | ||
| CHRG pin voltage absolute maximum | CHRG | -0.3 | 8 | V | 1 | ||
| STDBY pin voltage absolute maximum | STDBY | -0.3 | 8 | V | 1 | ||
| TEMP pin voltage absolute maximum | TEMP | -0.3 | 8 | V | 1 | ||
| CE pin voltage absolute maximum | CE | -0.3 | 8 | V | 1 | ||
| BAT Pin Current absolute maximum | 1100 | mA | 1 | ||||
| PROG Pin Current absolute maximum | 1000 | μA | 1 | ||||
| Maximum Junction Temperature | 145 | ℃ | 1 | ||||
| Lead Temperature (Soldering, 10 sec) | 260 | ℃ | 10 sec soldering | 1 | |||
| Storage Temperature Range | -65 | 125 | ℃ | 1 | |||
| Operating Ambient Temperature Range | -10 | 85 | ℃ | 1 | |||
| Thermal resistance junction to ambient | θJA | 125 | ℃/W | Figure 4 test condition (VBAT=3.75V, TA=25℃, RPROG=0.86K) | 11 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | IC runs from the chip to the lead frame and reaches the copper surface of the PC board | 11 |
CAD (KiCad official)
- Symbol:
TP4066-4.2V-DFN228 - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
tp4066-4-2v-dfn228-etched.step/tp4066-4-2v-dfn228-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tp4066-4-2v-dfn228.step/tp4066-4-2v-dfn228.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TOPPOWER(Nanjing Extension Microelectronics) datasheet (15 pp, sha256
3bf04897aaa9e7ef, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).