Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

TP4066-4.2V-DFN228

TOPPOWER(Nanjing Extension Microelectronics) · Battery Management · DFN-8-EP(2x2)

TP4066-4.2V-DFN228 from TOPPOWER(Nanjing Extension Microelectronics), in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TEMP input Temperature sense input connected to the battery NTC; charging is suspended if TEMP is below 45% or above 80% of VIN, and the function is disabled by grounding TEMP.
2 PROG passive Sets the constant charge current via a resistor RPROG to GND, with the pin regulated to 1V in constant current mode and 0.2V in precharge mode.
3 GND power_in Ground terminal.
4 VCC power_in Positive input supply voltage; the operating range is 4.35V to 12.0V, and the chip enters sleep mode when VCC drops to within 50mV of the BAT pin voltage.
5 BAT power_out Battery connection that supplies charge current to the battery and provides the 4.2V regulation voltage; it draws less than 1uA in shutdown or sleep mode.
6 STDBY output Open-drain charge termination status output that is pulled low when charging is terminated and is otherwise high impedance.
7 CHRG output Open-drain charge status output that is pulled low while the battery is being charged and is otherwise high impedance.
8 CE input Chip enable input where a high level enables normal operation and a low level puts the device into disable mode; it can be driven by TTL or CMOS logic levels.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer TOPPOWER(Nanjing Extension Microelectronics)
Package DFN-8-EP(2x2)
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Supply Voltage VCC 4.35 5 12 V ● full operating temperature range 3
Overvoltage protection point VOVP 6.5 7 7.5 V ● full operating temperature range 3
Regulated Output (Float) Voltage 4.2V VFLOAT 4.158 4.2 4.242 V 0℃≤TA≤85℃ 3
Charge current RPROG=1.2K IBAT 442 520 598 mA RPROG=1.2K, Current Mode 3
Charge current RPROG=0.7K IBAT 850 1000 1150 mA RPROG=0.7K, Current Mode 3
Trickle Charge Current ITRIKL 90 130 170 mA VBAT<VTRIKL, RPROG=0.7K 3
Trickle Charge Threshold Voltage VTRIKL 2.8 2.9 3 V RPROG=0.7K, VBAT Rising 3
Trickle Charge Hysteresis Voltage VTRHYS 60 80 100 mV RPROG=0.7K 3
VCC UVLO Voltage VUV 3.5 3.7 3.9 V VCC from low to high 3
VCC UVLO Hysteresis VUVHYS 150 200 300 mV ● 3
VCC-VBAT lockout threshold voltage (rising) VASD 130 160 190 mV VCC from low to high 3
VCC-VBAT lockout threshold voltage (falling) VASD 30 50 70 mV VCC from high to low 3
C/10 termination current threshold RPROG=1.2K ITERM 30 45 60 mA RPROG=1.2K 3
C/10 termination current threshold RPROG=0.7K ITERM 60 100 140 mA RPROG=0.7K 3
PROG pin voltage VPROG 0.9 1 1.1 V RPROG=0.7K, current mode 3
CHRG pin output low voltage 0.2 0.6 V I=20mA 3
STDBY pin output low voltage 0.2 0.6 V I=20mA 3
TEMP upper trip threshold VTEMP-H 80 82 %Vcc 3
TEMP lower trip threshold VTEMP-L 43 45 %Vcc 3
Recharge battery threshold voltage ΔVRECHRG 90 110 130 mV VFLOAL=4.2V 3
Recharge comparator filter time tRECHARGE 0.8 1.8 4 ms VBAT from high to low 4
Termination comparator filter time tTERM 0.8 1.8 4 ms IBAT drops below ICHG/10 4
Vcc adaptive starting voltage VADPT 4.1 4.3 4.5 V Rprog=0.7K, Vcc from high to low 4
BAT reverse leakage current IBAT 25 30 mA BAT reverse, VIN =5V 4
Input Supply Current Charge Mode ICC 120 200 μA Charge Mode, RPROG = 0.7K, ● 3
Input Supply Current Standby Mode (Charge Terminated) ICC 90 200 μA Standby Mode (Charge Terminated), ● 3
Input Supply Current Shutdown Mode ICC 90 200 μA Shutdown Mode (RPROG Not Connected, VCC < VBAT, or VCC < VUV), ● 3
Junction Temperature in Constant Temperature Mode TLIM 145 ℃ 3
The resistance of power FET ON (between VCC and BAT) RON 400 mΩ 3
Soft-start time tss 20 us IBAT=0 to IBAT=1100V/RPROG 4
PROG pin pull-up current IPROG 2 μA 4
Input Supply Voltage absolute maximum VCC -0.3 12 V 1
PROG pin voltage absolute maximum PROG -0.3 V VCC+0.3V 1
BAT pin voltage absolute maximum BAT -4.35 7 V 1
CHRG pin voltage absolute maximum CHRG -0.3 8 V 1
STDBY pin voltage absolute maximum STDBY -0.3 8 V 1
TEMP pin voltage absolute maximum TEMP -0.3 8 V 1
CE pin voltage absolute maximum CE -0.3 8 V 1
BAT Pin Current absolute maximum 1100 mA 1
PROG Pin Current absolute maximum 1000 μA 1
Maximum Junction Temperature 145 ℃ 1
Lead Temperature (Soldering, 10 sec) 260 ℃ 10 sec soldering 1
Storage Temperature Range -65 125 ℃ 1
Operating Ambient Temperature Range -10 85 ℃ 1
Thermal resistance junction to ambient θJA 125 ℃/W Figure 4 test condition (VBAT=3.75V, TA=25℃, RPROG=0.86K) 11

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper IC runs from the chip to the lead frame and reaches the copper surface of the PC board 11

CAD (KiCad official)

  • Symbol: TP4066-4.2V-DFN228
  • Footprint: Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm
  • 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: tp4066-4-2v-dfn228-etched.step / tp4066-4-2v-dfn228-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); tp4066-4-2v-dfn228.step / tp4066-4-2v-dfn228.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TOPPOWER(Nanjing Extension Microelectronics) datasheet (15 pp, sha256 3bf04897aaa9e7ef, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF