Generated by kicad-footprint-generator · KiCad file format 20260206
STM32WB55CGU6TR
STMicroelectronics · RF Transceiver ICs · UFQFPN-48(7x7)
STM32WB55CGU6TR from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup domain supply (RTC, LSE, backup registers) from a battery, supercapacitor or VDD; operating range 1.55 to 3.6 V. |
| 2 | PC14-OSC32_IN | bidirectional | FT I/O supplied through the power switch (3 mA sink limit, max 2 MHz with 30 pF load in output mode); additional function OSC32_IN for the LSE crystal. |
| 3 | PC15-OSC32_OUT | bidirectional | FT I/O supplied through the power switch (3 mA sink limit, max 2 MHz with 30 pF load in output mode); additional function OSC32_OUT for the LSE crystal. |
| 4 | PH3-BOOT0 | bidirectional | FT I/O with BOOT0 function; alternate functions CM4_EVENTOUT and LSCO. |
| 5 | PB8 | bidirectional | FT_fl I/O with alternate functions TIM1_CH2N, SAI1_PDM_CK1, I2C1_SCL, QUADSPI_BK1_IO1, LCD_SEG16, SAI1_MCLK_A, TIM16_CH1. |
| 6 | PB9 | bidirectional | FT_fla I/O with alternate functions TIM1_CH3N, SAI1_PDM_DI2, I2C1_SDA, SPI2_NSS, IR_OUT, TSC_G7_IO4, QUADSPI_BK1_IO0, LCD_COM3, SAI1_FS_A, TIM17_CH1. |
| 7 | NRST | bidirectional | Bidirectional reset pin with weak pull-up resistor. |
| 8 | VDDA | power_in | Analog supply for ADC, comparators and voltage reference buffer, 1.62 to 3.6 V; connected to VREF+ on UFQFPN48 and tied to VDD when unused. |
| 9 | PA0 | bidirectional | FT_a I/O with TIM2_CH1, COMP1_OUT, SAI1_EXTCLK, TIM2_ETR; additional functions COMP1_INM, ADC1_IN5, RTC_TAMP2/WKUP1. |
| 10 | PA1 | bidirectional | FT_la I/O with TIM2_CH2, I2C1_SMBA, SPI1_SCK, LCD_SEG0; additional functions COMP1_INP, ADC1_IN6. |
| 11 | PA2 | bidirectional | FT_la I/O with LSCO, TIM2_CH3, LPUART1_TX, QUADSPI_BK1_NCS, LCD_SEG1, COMP2_OUT; additional functions COMP2_INM, ADC1_IN7, WKUP4. |
| 12 | PA3 | bidirectional | FT_la I/O with TIM2_CH4, SAI1_PDM_CK1, LPUART1_RX, QUADSPI_CLK, LCD_SEG2, SAI1_MCLK_A; additional functions COMP2_INP, ADC1_IN8. |
| 13 | PA4 | bidirectional | FT_a I/O with SPI1_NSS, SAI1_FS_B, LPTIM2_OUT, LCD_SEG5; additional functions COMP1_INM, COMP2_INM, ADC1_IN9. |
| 14 | PA5 | bidirectional | FT_a I/O with TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR, SAI1_SD_B; additional functions COMP1_INM, COMP2_INM, ADC1_IN10. |
| 15 | PA6 | bidirectional | FT_la I/O with TIM1_BKIN, SPI1_MISO, LPUART1_CTS, QUADSPI_BK1_IO3, LCD_SEG3, TIM16_CH1; additional function ADC1_IN11. |
| 16 | PA7 | bidirectional | FT_fla I/O with TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, LCD_SEG4, COMP2_OUT, TIM17_CH1; additional function ADC1_IN12. |
| 17 | PA8 | bidirectional | FT_la I/O with MCO, TIM1_CH1, SAI1_PDM_CK2, USART1_CK, LCD_COM0, SAI1_SCK_A, LPTIM2_OUT; additional function ADC1_IN15. |
| 18 | PA9 | bidirectional | FT_fla I/O with TIM1_CH2, SAI1_PDM_DI2, I2C1_SCL, SPI2_SCK, USART1_TX, LCD_COM1, SAI1_FS_A; additional functions COMP1_INM, ADC1_IN16. |
| 19 | PB2 | bidirectional | FT_a I/O with RTC_OUT, LPTIM1_OUT, I2C3_SMBA, SPI1_NSS, LCD_VLCD, SAI1_EXTCLK; additional function COMP1_INP. |
| 20 | VDD | power_in | Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions. |
| 21 | RF1 | bidirectional | RF input/output, must be connected to the antenna through a low-pass matching network; use the nominal PCB layout. |
| 22 | VSSRF | power_in | RF ground, to be connected to GND. |
| 23 | VDDRF | power_in | Dedicated RF supply, must be connected to VDD. |
| 24 | OSC_OUT | output | 32 MHz main oscillator output, also HSE source; use the nominal PCB layout per reference design (AN5165). |
| 25 | OSC_IN | input | 32 MHz main oscillator input, also HSE source; use the nominal PCB layout per reference design (AN5165). |
| 26 | AT0 | unconnected | Reserved RF pin, must be kept unconnected. |
| 27 | AT1 | unconnected | Reserved RF pin, must be kept unconnected. |
| 28 | PB0 | bidirectional | TT I/O with COMP1_OUT, RF_TX_MOD_EXT_PA (external PA transmit control); output speed should be set to 00 during RF operation since frequencies above 32 kHz may impact RF performance. |
| 29 | PB1 | bidirectional | TT I/O with LPUART1_RTS_DE, LPTIM2_IN1; output speed should be set to 00 during RF operation since frequencies above 32 kHz may impact RF performance. |
| 30 | PE4 | bidirectional | FT I/O with alternate function CM4_EVENTOUT. |
| 31 | VFBSMPS | passive | SMPS step-down converter feedback voltage pin (VFBSMPS range 1.4 to 3.6 V). |
| 32 | VSSSMPS | power_in | SMPS step-down converter ground. |
| 33 | VLXSMPS | passive | SMPS step-down converter switching node connecting to the external inductor L1. |
| 34 | VDDSMPS | power_in | SMPS step-down converter supply, must always be connected to VDD. |
| 35 | VDD | power_in | Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions. |
| 36 | PA10 | bidirectional | FT_fl I/O with TIM1_CH3, SAI1_PDM_DI1, I2C1_SDA, USART1_RX, USB_CRS_SYNC, LCD_COM2, SAI1_SD_A, TIM17_BKIN. |
| 37 | PA11 | bidirectional | FT_u I/O with TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, USB_DM, powered by VDDUSB when USB function is selected. |
| 38 | PA12 | bidirectional | FT_u I/O with TIM1_ETR, SPI1_MOSI, LPUART1_RX, USART1_RTS_DE, USB_DP, powered by VDDUSB when USB function is selected. |
| 39 | PA13 | bidirectional | FT_u I/O, JTMS-SWDIO after reset with internal pull-up active; also IR_OUT, USB_NOE, SAI1_SD_B. |
| 40 | VDDUSB | power_in | Independent USB transceiver supply, 3.0 to 3.6 V; connect to VDD or ground when USB is not used. |
| 41 | PA14 | bidirectional | FT_l I/O, JTCK-SWCLK after reset with internal pull-down active; also LPTIM1_OUT, I2C1_SMBA, LCD_SEG5, SAI1_FS_B. |
| 42 | PA15 | bidirectional | FT_l I/O, JTDI after reset with internal pull-up active; also TIM2_CH1, TIM2_ETR, SPI1_NSS, TSC_G3_IO1, LCD_SEG17, MCO. |
| 43 | PB3 | bidirectional | FT_la I/O, JTDO-TRACESWO after reset; also TIM2_CH2, SPI1_SCK, USART1_RTS_DE, LCD_SEG7, SAI1_SCK_B; additional function COMP2_INM. |
| 44 | PB4 | bidirectional | FT_fla I/O, NJTRST after reset with internal pull-up active; also I2C3_SDA, SPI1_MISO, USART1_CTS, TSC_G2_IO1, LCD_SEG8, SAI1_MCLK_B, TIM17_BKIN; additional function COMP2_INP. |
| 45 | PB5 | bidirectional | FT_l I/O with LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, USART1_CK, LPUART1_TX, TSC_G2_IO2, LCD_SEG9, COMP2_OUT, SAI1_SD_B, TIM16_BKIN. |
| 46 | PB6 | bidirectional | FT_fla I/O with LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, LCD_SEG6, SAI1_FS_B, TIM16_CH1N, MCO; additional function COMP2_INP. |
| 47 | PB7 | bidirectional | FT_fla I/O with LPTIM1_IN2, TIM1_BKIN, I2C1_SDA, USART1_RX, TSC_G2_IO4, LCD_SEG21, TIM17_CH1N; additional functions COMP2_INM, PVD_IN. |
| 48 | VDD | power_in | Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Radio Frequency Chip/Antenna |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage | VDDX - VSS | -0.3 | 4 | V | including VDD, VDDA, VDDUSB, VLCD, VDDRF, VDDSMPS, VBAT, VREF+ | 85 | |
| Variations between different VDDX power pins of same domain | /ΔVDDx/ | 50 | mV | 85 | |||
| Variations between all different ground pins | /VSSx-VSS/ | 50 | mV | 85 | |||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | 85 | |||
| Total current into all VDD power lines | ΣIVDD | 130 | mA | source | 85 | ||
| Total current out of all VSS ground lines | ΣIVSS | 130 | mA | sink | 85 | ||
| Maximum current into each VDD pin | IVDD(PIN) | 100 | mA | source | 85 | ||
| Maximum current out of each VSS pin | IVSS(PIN) | 100 | mA | sink | 85 | ||
| Output current sunk by any I/O and control pin | IIO(PIN) | 20 | mA | except FT_f | 85 | ||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 85 | |||
| Total output current sunk by all I/Os and control pins | ΣIIO(PIN) | 100 | mA | 85 | |||
| Total output current sourced by all I/Os and control pins | ΣIIO(PIN) | 100 | mA | 85 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins | IINJ(PIN) | -5 | 0 | mA | except PB0 and PB1 | 85 | |
| Total injected current | Σ/IINJ(PIN)/ | 25 | mA | sum of all I/Os and control pins | 85 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 86 | ||
| Maximum junction temperature | TJ | 130 | °C | 86 | |||
| Internal AHB clock frequency | fHCLK | 0 | 64 | MHz | 87 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 64 | MHz | 87 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 64 | MHz | 87 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 87 | ||
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 87 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 87 | |
| Analog supply voltage | VDDA | 1.71 | 3.6 | V | ADC, COMP, VREFBUF not used | 87 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 87 | ||
| SMPS Feedback voltage | VFBSMPS | 1.4 | 3.6 | V | 88 | ||
| Minimum RF voltage | VDDRF | 1.71 | 3.6 | V | 88 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 88 | |
| USB supply voltage | VDDUSB | 0 | 3.6 | V | USB not used | 88 | |
| Power dissipation UFQFPN48 | PD | 803 | mW | TA = 85 °C for suffix 6 | 88 | ||
| Ambient temperature suffix 6 | TA | -40 | 85 | °C | Maximum power dissipation | 88 | |
| Ambient temperature suffix 6, low-power dissipation | TA | -40 | 105 | °C | Low-power dissipation | 88 | |
| Junction temperature range suffix 6 | TJ | -40 | 105 | °C | Suffix 6 version | 88 | |
| Brown-out reset threshold 0 rising | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 96 |
| Brown-out reset threshold 0 falling | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 96 |
| Brown-out reset threshold 1 rising | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 96 |
| Brown-out reset threshold 1 falling | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 96 |
| Brown-out reset threshold 2 rising | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 96 |
| Brown-out reset threshold 2 falling | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 96 |
| Brown-out reset threshold 3 rising | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 96 |
| Brown-out reset threshold 3 falling | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 96 |
| Brown-out reset threshold 4 rising | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 96 |
| Brown-out reset threshold 4 falling | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 96 |
| Reset temporization after BOR0 detected | tRSTTEMPO | 250 | 400 | μs | VDD rising | 96 | |
| PVD threshold 0 rising | VPVD0 | 2.1 | 2.15 | 2.19 | V | Rising edge | 96 |
| PVD threshold 0 falling | VPVD0 | 2 | 2.05 | 2.1 | V | Falling edge | 96 |
| PVD threshold 1 rising | VPVD1 | 2.26 | 2.31 | 2.36 | V | Rising edge | 96 |
| PVD threshold 1 falling | VPVD1 | 2.15 | 2.2 | 2.25 | V | Falling edge | 96 |
| PVD threshold 2 rising | VPVD2 | 2.41 | 2.46 | 2.51 | V | Rising edge | 96 |
| PVD threshold 2 falling | VPVD2 | 2.31 | 2.36 | 2.41 | V | Falling edge | 96 |
| PVD threshold 3 rising | VPVD3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 97 |
| PVD threshold 3 falling | VPVD3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 97 |
| PVD threshold 4 rising | VPVD4 | 2.69 | 2.74 | 2.79 | V | Rising edge | 97 |
| PVD threshold 4 falling | VPVD4 | 2.59 | 2.64 | 2.69 | V | Falling edge | 97 |
| PVD threshold 5 rising | VPVD5 | 2.85 | 2.91 | 2.96 | V | Rising edge | 97 |
| PVD threshold 5 falling | VPVD5 | 2.75 | 2.81 | 2.86 | V | Falling edge | 97 |
| PVD threshold 6 rising | VPVD6 | 2.92 | 2.98 | 3.04 | V | Rising edge | 97 |
| PVD threshold 6 falling | VPVD6 | 2.84 | 2.9 | 2.96 | V | Falling edge | 97 |
| VDDUSB peripheral voltage monitoring | VPVM1 | 1.18 | 1.22 | 1.26 | V | 97 | |
| VDDA peripheral voltage monitoring rising | VPVM3 | 1.61 | 1.65 | 1.69 | V | Rising edge | 97 |
| VDDA peripheral voltage monitoring falling | VPVM3 | 1.6 | 1.64 | 1.68 | V | Falling edge | 97 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +125 °C | 98 |
CAD (KiCad official)
- Symbol:
STM32WB55CGU6TR - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32wb55cgu6tr-etched.step/stm32wb55cgu6tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32wb55cgu6tr.step/stm32wb55cgu6tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (196 pp, sha256
c25acc0a128f2941, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).