main
Ray Publish 0.1.0 ef205fe

STM32WB55CGU6TR

STMicroelectronics · RF Transceiver ICs · UFQFPN-48(7x7)

STM32WB55CGU6TR from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup domain supply (RTC, LSE, backup registers) from a battery, supercapacitor or VDD; operating range 1.55 to 3.6 V.
2 PC14-OSC32_IN bidirectional FT I/O supplied through the power switch (3 mA sink limit, max 2 MHz with 30 pF load in output mode); additional function OSC32_IN for the LSE crystal.
3 PC15-OSC32_OUT bidirectional FT I/O supplied through the power switch (3 mA sink limit, max 2 MHz with 30 pF load in output mode); additional function OSC32_OUT for the LSE crystal.
4 PH3-BOOT0 bidirectional FT I/O with BOOT0 function; alternate functions CM4_EVENTOUT and LSCO.
5 PB8 bidirectional FT_fl I/O with alternate functions TIM1_CH2N, SAI1_PDM_CK1, I2C1_SCL, QUADSPI_BK1_IO1, LCD_SEG16, SAI1_MCLK_A, TIM16_CH1.
6 PB9 bidirectional FT_fla I/O with alternate functions TIM1_CH3N, SAI1_PDM_DI2, I2C1_SDA, SPI2_NSS, IR_OUT, TSC_G7_IO4, QUADSPI_BK1_IO0, LCD_COM3, SAI1_FS_A, TIM17_CH1.
7 NRST bidirectional Bidirectional reset pin with weak pull-up resistor.
8 VDDA power_in Analog supply for ADC, comparators and voltage reference buffer, 1.62 to 3.6 V; connected to VREF+ on UFQFPN48 and tied to VDD when unused.
9 PA0 bidirectional FT_a I/O with TIM2_CH1, COMP1_OUT, SAI1_EXTCLK, TIM2_ETR; additional functions COMP1_INM, ADC1_IN5, RTC_TAMP2/WKUP1.
10 PA1 bidirectional FT_la I/O with TIM2_CH2, I2C1_SMBA, SPI1_SCK, LCD_SEG0; additional functions COMP1_INP, ADC1_IN6.
11 PA2 bidirectional FT_la I/O with LSCO, TIM2_CH3, LPUART1_TX, QUADSPI_BK1_NCS, LCD_SEG1, COMP2_OUT; additional functions COMP2_INM, ADC1_IN7, WKUP4.
12 PA3 bidirectional FT_la I/O with TIM2_CH4, SAI1_PDM_CK1, LPUART1_RX, QUADSPI_CLK, LCD_SEG2, SAI1_MCLK_A; additional functions COMP2_INP, ADC1_IN8.
13 PA4 bidirectional FT_a I/O with SPI1_NSS, SAI1_FS_B, LPTIM2_OUT, LCD_SEG5; additional functions COMP1_INM, COMP2_INM, ADC1_IN9.
14 PA5 bidirectional FT_a I/O with TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR, SAI1_SD_B; additional functions COMP1_INM, COMP2_INM, ADC1_IN10.
15 PA6 bidirectional FT_la I/O with TIM1_BKIN, SPI1_MISO, LPUART1_CTS, QUADSPI_BK1_IO3, LCD_SEG3, TIM16_CH1; additional function ADC1_IN11.
16 PA7 bidirectional FT_fla I/O with TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2, LCD_SEG4, COMP2_OUT, TIM17_CH1; additional function ADC1_IN12.
17 PA8 bidirectional FT_la I/O with MCO, TIM1_CH1, SAI1_PDM_CK2, USART1_CK, LCD_COM0, SAI1_SCK_A, LPTIM2_OUT; additional function ADC1_IN15.
18 PA9 bidirectional FT_fla I/O with TIM1_CH2, SAI1_PDM_DI2, I2C1_SCL, SPI2_SCK, USART1_TX, LCD_COM1, SAI1_FS_A; additional functions COMP1_INM, ADC1_IN16.
19 PB2 bidirectional FT_a I/O with RTC_OUT, LPTIM1_OUT, I2C3_SMBA, SPI1_NSS, LCD_VLCD, SAI1_EXTCLK; additional function COMP1_INP.
20 VDD power_in Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions.
21 RF1 bidirectional RF input/output, must be connected to the antenna through a low-pass matching network; use the nominal PCB layout.
22 VSSRF power_in RF ground, to be connected to GND.
23 VDDRF power_in Dedicated RF supply, must be connected to VDD.
24 OSC_OUT output 32 MHz main oscillator output, also HSE source; use the nominal PCB layout per reference design (AN5165).
25 OSC_IN input 32 MHz main oscillator input, also HSE source; use the nominal PCB layout per reference design (AN5165).
26 AT0 unconnected Reserved RF pin, must be kept unconnected.
27 AT1 unconnected Reserved RF pin, must be kept unconnected.
28 PB0 bidirectional TT I/O with COMP1_OUT, RF_TX_MOD_EXT_PA (external PA transmit control); output speed should be set to 00 during RF operation since frequencies above 32 kHz may impact RF performance.
29 PB1 bidirectional TT I/O with LPUART1_RTS_DE, LPTIM2_IN1; output speed should be set to 00 during RF operation since frequencies above 32 kHz may impact RF performance.
30 PE4 bidirectional FT I/O with alternate function CM4_EVENTOUT.
31 VFBSMPS passive SMPS step-down converter feedback voltage pin (VFBSMPS range 1.4 to 3.6 V).
32 VSSSMPS power_in SMPS step-down converter ground.
33 VLXSMPS passive SMPS step-down converter switching node connecting to the external inductor L1.
34 VDDSMPS power_in SMPS step-down converter supply, must always be connected to VDD.
35 VDD power_in Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions.
36 PA10 bidirectional FT_fl I/O with TIM1_CH3, SAI1_PDM_DI1, I2C1_SDA, USART1_RX, USB_CRS_SYNC, LCD_COM2, SAI1_SD_A, TIM17_BKIN.
37 PA11 bidirectional FT_u I/O with TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS, USB_DM, powered by VDDUSB when USB function is selected.
38 PA12 bidirectional FT_u I/O with TIM1_ETR, SPI1_MOSI, LPUART1_RX, USART1_RTS_DE, USB_DP, powered by VDDUSB when USB function is selected.
39 PA13 bidirectional FT_u I/O, JTMS-SWDIO after reset with internal pull-up active; also IR_OUT, USB_NOE, SAI1_SD_B.
40 VDDUSB power_in Independent USB transceiver supply, 3.0 to 3.6 V; connect to VDD or ground when USB is not used.
41 PA14 bidirectional FT_l I/O, JTCK-SWCLK after reset with internal pull-down active; also LPTIM1_OUT, I2C1_SMBA, LCD_SEG5, SAI1_FS_B.
42 PA15 bidirectional FT_l I/O, JTDI after reset with internal pull-up active; also TIM2_CH1, TIM2_ETR, SPI1_NSS, TSC_G3_IO1, LCD_SEG17, MCO.
43 PB3 bidirectional FT_la I/O, JTDO-TRACESWO after reset; also TIM2_CH2, SPI1_SCK, USART1_RTS_DE, LCD_SEG7, SAI1_SCK_B; additional function COMP2_INM.
44 PB4 bidirectional FT_fla I/O, NJTRST after reset with internal pull-up active; also I2C3_SDA, SPI1_MISO, USART1_CTS, TSC_G2_IO1, LCD_SEG8, SAI1_MCLK_B, TIM17_BKIN; additional function COMP2_INP.
45 PB5 bidirectional FT_l I/O with LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, USART1_CK, LPUART1_TX, TSC_G2_IO2, LCD_SEG9, COMP2_OUT, SAI1_SD_B, TIM16_BKIN.
46 PB6 bidirectional FT_fla I/O with LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, LCD_SEG6, SAI1_FS_B, TIM16_CH1N, MCO; additional function COMP2_INP.
47 PB7 bidirectional FT_fla I/O with LPTIM1_IN2, TIM1_BKIN, I2C1_SDA, USART1_RX, TSC_G2_IO4, LCD_SEG21, TIM17_CH1N; additional functions COMP2_INM, PVD_IN.
48 VDD power_in Digital supply, 1.71 to 3.6 V, for I/Os, internal regulator and system functions.
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Radio Frequency Chip/Antenna
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage VDDX - VSS -0.3 4 V including VDD, VDDA, VDDUSB, VLCD, VDDRF, VDDSMPS, VBAT, VREF+ 85
Variations between different VDDX power pins of same domain /ΔVDDx/ 50 mV 85
Variations between all different ground pins /VSSx-VSS/ 50 mV 85
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V 85
Total current into all VDD power lines ΣIVDD 130 mA source 85
Total current out of all VSS ground lines ΣIVSS 130 mA sink 85
Maximum current into each VDD pin IVDD(PIN) 100 mA source 85
Maximum current out of each VSS pin IVSS(PIN) 100 mA sink 85
Output current sunk by any I/O and control pin IIO(PIN) 20 mA except FT_f 85
Output current sourced by any I/O and control pin IIO(PIN) 20 mA 85
Total output current sunk by all I/Os and control pins ΣIIO(PIN) 100 mA 85
Total output current sourced by all I/Os and control pins ΣIIO(PIN) 100 mA 85
Injected current on FT_xxx, TT_xx, RST and B pins IINJ(PIN) -5 0 mA except PB0 and PB1 85
Total injected current Σ/IINJ(PIN)/ 25 mA sum of all I/Os and control pins 85
Storage temperature range TSTG -65 150 °C 86
Maximum junction temperature TJ 130 °C 86
Internal AHB clock frequency fHCLK 0 64 MHz 87
Internal APB1 clock frequency fPCLK1 0 64 MHz 87
Internal APB2 clock frequency fPCLK2 0 64 MHz 87
Standard operating voltage VDD 1.71 3.6 V 87
Analog supply voltage VDDA 1.62 3.6 V ADC or COMP used 87
Analog supply voltage VDDA 2.4 3.6 V VREFBUF used 87
Analog supply voltage VDDA 1.71 3.6 V ADC, COMP, VREFBUF not used 87
Backup operating voltage VBAT 1.55 3.6 V 87
SMPS Feedback voltage VFBSMPS 1.4 3.6 V 88
Minimum RF voltage VDDRF 1.71 3.6 V 88
USB supply voltage VDDUSB 3 3.6 V USB used 88
USB supply voltage VDDUSB 0 3.6 V USB not used 88
Power dissipation UFQFPN48 PD 803 mW TA = 85 °C for suffix 6 88
Ambient temperature suffix 6 TA -40 85 °C Maximum power dissipation 88
Ambient temperature suffix 6, low-power dissipation TA -40 105 °C Low-power dissipation 88
Junction temperature range suffix 6 TJ -40 105 °C Suffix 6 version 88
Brown-out reset threshold 0 rising VBOR0 1.62 1.66 1.7 V Rising edge 96
Brown-out reset threshold 0 falling VBOR0 1.6 1.64 1.69 V Falling edge 96
Brown-out reset threshold 1 rising VBOR1 2.06 2.1 2.14 V Rising edge 96
Brown-out reset threshold 1 falling VBOR1 1.96 2 2.04 V Falling edge 96
Brown-out reset threshold 2 rising VBOR2 2.26 2.31 2.35 V Rising edge 96
Brown-out reset threshold 2 falling VBOR2 2.16 2.2 2.24 V Falling edge 96
Brown-out reset threshold 3 rising VBOR3 2.56 2.61 2.66 V Rising edge 96
Brown-out reset threshold 3 falling VBOR3 2.47 2.52 2.57 V Falling edge 96
Brown-out reset threshold 4 rising VBOR4 2.85 2.9 2.95 V Rising edge 96
Brown-out reset threshold 4 falling VBOR4 2.76 2.81 2.86 V Falling edge 96
Reset temporization after BOR0 detected tRSTTEMPO 250 400 μs VDD rising 96
PVD threshold 0 rising VPVD0 2.1 2.15 2.19 V Rising edge 96
PVD threshold 0 falling VPVD0 2 2.05 2.1 V Falling edge 96
PVD threshold 1 rising VPVD1 2.26 2.31 2.36 V Rising edge 96
PVD threshold 1 falling VPVD1 2.15 2.2 2.25 V Falling edge 96
PVD threshold 2 rising VPVD2 2.41 2.46 2.51 V Rising edge 96
PVD threshold 2 falling VPVD2 2.31 2.36 2.41 V Falling edge 96
PVD threshold 3 rising VPVD3 2.56 2.61 2.66 V Rising edge 97
PVD threshold 3 falling VPVD3 2.47 2.52 2.57 V Falling edge 97
PVD threshold 4 rising VPVD4 2.69 2.74 2.79 V Rising edge 97
PVD threshold 4 falling VPVD4 2.59 2.64 2.69 V Falling edge 97
PVD threshold 5 rising VPVD5 2.85 2.91 2.96 V Rising edge 97
PVD threshold 5 falling VPVD5 2.75 2.81 2.86 V Falling edge 97
PVD threshold 6 rising VPVD6 2.92 2.98 3.04 V Rising edge 97
PVD threshold 6 falling VPVD6 2.84 2.9 2.96 V Falling edge 97
VDDUSB peripheral voltage monitoring VPVM1 1.18 1.22 1.26 V 97
VDDA peripheral voltage monitoring rising VPVM3 1.61 1.65 1.69 V Rising edge 97
VDDA peripheral voltage monitoring falling VPVM3 1.6 1.64 1.68 V Falling edge 97
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40 °C < TA < +125 °C 98

CAD (KiCad official)

  • Symbol: STM32WB55CGU6TR
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32wb55cgu6tr-etched.step / stm32wb55cgu6tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32wb55cgu6tr.step / stm32wb55cgu6tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (196 pp, sha256 c25acc0a128f2941, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF