Generated by kicad-footprint-generator · KiCad file format 20260206
STM32L562CEU6
STMicroelectronics · ST Microelectronics · UFQFPN-48(7x7)
STM32L562CEU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup supply (1.55 V to 3.6 V) for the RTC, the external 32 kHz oscillator and the backup registers when VDD is not present. |
| 2 | PC13 | bidirectional | FT I/O supplied through the power switch, which sinks only 3 mA, so in output mode it must not exceed 2 MHz with a 30 pF maximum load and must not be used as a current source; additional functions are WKUP2, RTC_TS/RTC_OUT1 and TAMP_IN1/TAMP_OUT2. |
| 3 | PC14-OSC32_IN | bidirectional | FT I/O on the power switch with the same 3 mA limit (output at most 2 MHz with 30 pF, no current-source use), doubling as the 32 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | FT I/O on the power switch with the same 3 mA limit (output at most 2 MHz with 30 pF, no current-source use), doubling as the 32 kHz oscillator output OSC32_OUT. |
| 5 | PH0-OSC_IN | bidirectional | FT I/O (PH0) that doubles as the high-speed external oscillator input OSC_IN, with EVENTOUT as its only alternate function. |
| 6 | PH1-OSC_OUT | bidirectional | FT I/O (PH1) that doubles as the high-speed external oscillator output OSC_OUT, with EVENTOUT as its only alternate function. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor; functionality is guaranteed when reset is released down to VBOR0 min. |
| 8 | VSSA/VREF- | power_in | Analog ground; VREF- must always be equal to VSSA, and on this package the pin is bonded to VSSA. |
| 9 | VDDA/VREF+ | power_in | Analog supply of 1.62 V (ADCs/COMPs) or 1.8 V (DACs/OPAMPs) to 3.6 V; VREF+ is double-bonded to VDDA here, so the internal voltage reference buffer is unavailable and must stay disabled, and VREF+ must equal VDDA when VDDA is below 2 V. |
| 10 | PA0 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM5_CH1, TIM8_ETR, USART2_CTS/USART2_NSS, UART4_TX, SAI1_EXTCLK and TIM2_ETR alternate functions; additional OPAMP1_VINP, ADC12_IN5, WKUP1 and TAMP_IN2/TAMP_OUT1. |
| 11 | PA1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH2, TIM5_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS/USART2_DE, UART4_RX, OCTOSPI1_DQS and TIM15_CH1N alternate functions; additional OPAMP1_VINM, ADC12_IN6 and TAMP_IN5/TAMP_OUT4. |
| 12 | PA2 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH3, TIM5_CH3, USART2_TX, LPUART1_TX, OCTOSPI1_NCS, UCPD1_FRSTX1, SAI2_EXTCLK and TIM15_CH1 alternate functions; additional ADC12_IN7, WKUP4/LSCO and COMP1_INP. |
| 13 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH4, TIM5_CH4, SAI1_CK1, USART2_RX, LPUART1_RX, OCTOSPI1_CLK, SAI1_MCLK_A and TIM15_CH2 alternate functions; additional OPAMP1_VOUT and ADC12_IN8. |
| 14 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with OCTOSPI1_NCS, SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B and LPTIM2_OUT alternate functions; additional ADC12_IN9 and DAC1_OUT1. |
| 15 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM2_ETR, TIM8_CH1N, SPI1_SCK and LPTIM2_ETR alternate functions; additional ADC12_IN10 and DAC1_OUT2. |
| 16 | PA6 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO, USART3_CTS/USART3_NSS, LPUART1_CTS, OCTOSPI1_IO3 and TIM16_CH1 alternate functions; additional OPAMP2_VINP and ADC12_IN11. |
| 17 | PA7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI, OCTOSPI1_IO2 and TIM17_CH1 alternate functions; additional OPAMP2_VINM and ADC12_IN12. |
| 18 | PB0 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK, OCTOSPI1_IO1, COMP1_OUT and SAI1_EXTCLK alternate functions; additional OPAMP2_VOUT and ADC12_IN15. |
| 19 | PB1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN0, USART3_RTS/USART3_DE, LPUART1_RTS/LPUART1_DE, OCTOSPI1_IO0 and LPTIM2_IN1 alternate functions; additional COMP1_INM and ADC12_IN16. |
| 20 | PB2 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with LPTIM1_OUT, I2C3_SMBA, DFSDM1_CKIN0, OCTOSPI1_DQS and UCPD1_FRSTX1 alternate functions; additional RTC_OUT2 and COMP1_INP. |
| 21 | PB10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH3, LPTIM3_OUT, I2C4_SCL, I2C2_SCL, SPI2_SCK, USART3_TX, LPUART1_RX, TSC_SYNC, OCTOSPI1_CLK, COMP1_OUT and SAI1_SCK_A alternate functions. |
| 22 | PB11 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH4, I2C4_SDA, I2C2_SDA, USART3_RX, LPUART1_TX, OCTOSPI1_NCS and COMP2_OUT alternate functions. |
| 23 | VSS | power_in | Ground pin; all VSS pins must always be connected to the external ground within the permitted range. |
| 24 | VDD | power_in | Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks. |
| 25 | PB12 | bidirectional | FT I/O (5 V tolerant) with TIM1_BKIN, I2C2_SMBA, SPI2_NSS, DFSDM1_DATIN1, USART3_CK, LPUART1_RTS/LPUART1_DE, TSC_G1_IO1, OCTOSPI1_NCLK, SAI2_FS_A and TIM15_BKIN alternate functions. |
| 26 | PB13 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK, DFSDM1_CKIN1, USART3_CTS/USART3_NSS, LPUART1_CTS, TSC_G1_IO2, UCPD1_FRSTX2, SAI2_SCK_A and TIM15_CH1N alternate functions. |
| 27 | PB14 | bidirectional | FT_fd I/O (5 V tolerant, Fm+ capable, USB Type-C dead battery function) with TIM1_CH2N, LPTIM3_ETR, TIM8_CH2N, I2C2_SDA, SPI2_MISO, DFSDM1_DATIN2, USART3_RTS/USART3_DE, TSC_G1_IO3, SAI2_MCLK_A and TIM15_CH1 alternate functions; additional UCPD1_DB2. |
| 28 | PB15 | bidirectional | FT_c I/O (5 V tolerant, USB Type-C PD capable) with RTC_REFIN, TIM1_CH3N, TIM8_CH3N, SPI2_MOSI, DFSDM1_CKIN2, SAI2_SD_A and TIM15_CH2 alternate functions; additional UCPD1_CC2. |
| 29 | PA8 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with MCO, TIM1_CH1, SAI1_CK2, USART1_CK, SAI1_SCK_A and LPTIM2_OUT alternate functions. |
| 30 | PA9 | bidirectional | FT_fu I/O (5 V tolerant, Fm+ capable, USB function supplied by VDDUSB) with TIM1_CH2, SPI2_SCK, USART1_TX, SAI1_FS_A and TIM15_BKIN alternate functions. |
| 31 | PA10 | bidirectional | FT_fu I/O (5 V tolerant, Fm+ capable, USB function supplied by VDDUSB) with TIM1_CH3, SAI1_D1, USART1_RX, CRS_SYNC, SAI1_SD_A and TIM17_BKIN alternate functions. |
| 32 | PA11 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS/USART1_NSS, FDCAN1_RX and USB_DM alternate functions. |
| 33 | PA12 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_ETR, SPI1_MOSI, USART1_RTS/USART1_DE, FDCAN1_TX and USB_DP alternate functions. |
| 34 | PA13 (JTMS/SWDIO) | bidirectional | FT I/O that after reset is the JTMS/SWDIO debug function, with its internal pull-up activated; alternate functions include IR_OUT, USB_NOE, SAI1_SD_B and EVENTOUT. |
| 35 | VSS | power_in | Ground pin; all VSS pins must always be connected to the external ground within the permitted range. |
| 36 | VDD | power_in | Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks. |
| 37 | PA14 (JTCK/SWCLK) | bidirectional | FT I/O that after reset is the JTCK/SWCLK debug function, with its internal pull-down activated; alternate functions include LPTIM1_OUT, I2C1_SMBA, I2C4_SMBA, SAI1_FS_B and EVENTOUT. |
| 38 | PA15 (JTDI) | bidirectional | FT_c I/O (USB Type-C PD capable) that after reset is the JTDI debug function, with its internal pull-up activated; additional UCPD1_CC1 function. |
| 39 | PB3 (JTDO/TRACESWO) | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with JTDO/TRACESWO, TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS/USART1_DE, CRS_SYNC and SAI1_SCK_B alternate functions; additional COMP2_INM. |
| 40 | PB4 (NJTRST) | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that after reset is the NJTRST debug function with its internal pull-up activated; alternate functions include TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS/USART1_NSS and TIM17_BKIN; additional COMP2_INP. |
| 41 | PB5 | bidirectional | FT_d I/O (5 V tolerant, USB Type-C PD dead battery function) with LPTIM1_IN1, TIM3_CH2, OCTOSPI1_NCLK, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, UART5_CTS/UART5_NSS, COMP2_OUT, SAI1_SD_B and TIM16_BKIN alternate functions; additional UCPD1_DB1. |
| 42 | PB6 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with LPTIM1_ETR, TIM4_CH1, TIM8_BKIN2, I2C1_SCL, I2C4_SCL, USART1_TX, SAI1_FS_B and TIM16_CH1N alternate functions; additional COMP2_INP. |
| 43 | PB7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with LPTIM1_IN2, TIM4_CH2, TIM8_BKIN, I2C1_SDA, I2C4_SDA, USART1_RX, UART4_CTS, FMC_NL and TIM17_CH1N alternate functions; additional COMP2_INM and PVD_IN. |
| 44 | PH3-BOOT0 | bidirectional | FT I/O (PH3) that carries the BOOT0 function, with EVENTOUT as its only listed alternate function. |
| 45 | PB8 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM4_CH3, SAI1_CK1, I2C1_SCL, DFSDM1_CKOUT, SDMMC1_CKIN, FDCAN1_RX, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1 alternate functions. |
| 46 | PB9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with IR_OUT, TIM4_CH4, SAI1_D2, I2C1_SDA, SPI2_NSS, SDMMC1_CDIR, FDCAN1_TX, SDMMC1_D5, SAI1_FS_A and TIM17_CH1 alternate functions. |
| 47 | VSS | power_in | Ground pin; all VSS pins must always be connected to the external ground within the permitted range. |
| 48 | VDD | power_in | Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDD, VDDA, VDDIO2, VDDUSB, VBAT, VDDSMPS, VREF+) | VDDX - VSS | -0.3 | 4 | V | 147 | ||
| Input voltage on FT_xxx pins except FT_c (max = Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VDDSMPS)+4.0, 6.0) as printed) | VIN | -0.3 | V | 147 | |||
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | 147 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 147 | ||
| Allowed voltage difference for VREF+ > VDDA | VREF+ - VDDA | 0.4 | V | VREF+ > VDDA | 147 | ||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 147 | |||
| Variations between all the different ground pins (include VREF- pin) | /VSSx-VSS/ | 50 | mV | 148 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 160 | mA | 148 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 160 | mA | 148 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 148 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 148 | |||
| Output current sunk by any I/O and control pin | IIO(PIN) | 20 | mA | except FT_f pins | 148 | ||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | FT_f pin | 148 | ||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 148 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 148 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 148 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins | IINJ(PIN) | -5 | 0 | mA | except PA4, PA5 | 148 | |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | PA4, PA5 | 148 | |
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 148 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 149 | ||
| Maximum junction temperature | TJ | 150 | °C | 149 | |||
| Internal AHB clock frequency | fHCLK | 0 | 110 | MHz | 149 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 110 | MHz | 149 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 110 | MHz | 149 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 149 | ||
| PG[15:2] I/Os supply voltage | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used | 149 | |
| PG[15:2] I/Os supply voltage | VDDIO2 | 0 | 3.6 | V | PG[15:2] not used | 149 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 149 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 149 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 149 | |
| Analog supply voltage | VDDA | 0 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 149 | ||
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 150 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 150 | |
| USB supply voltage | VDDUSB | 0 | 3.6 | V | USB not used | 150 | |
| I/O input voltage (max VDDIOx+0.3 as printed) | VIN | -0.3 | V | TT_xx I/O | 150 | ||
| I/O input voltage | VIN | -0.3 | 5 | V | FT_c I/O | 150 | |
| I/O input voltage (max MIN(MIN(VDD, VDDA, VDDIO2, VDDUSB)+3.6 V, 5.5 V) as printed) | VIN | -0.3 | V | All I/O except FT_c and TT_xx | 150 | ||
| Ambient temperature, suffix 6 version, maximum power dissipation | TA | -40 | 85 | °C | Suffix 6 version, maximum power dissipation | 150 | |
| Ambient temperature, suffix 6 version, low-power dissipation | TA | -40 | 105 | °C | Suffix 6 version, low-power dissipation | 150 | |
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 150 | |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 153 | |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 153 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 153 |
| Brown-out reset threshold 1 | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 153 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 153 |
| Brown-out reset threshold 2 | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 153 |
| Brown-out reset threshold 2 | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 153 |
| Brown-out reset threshold 3 | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 153 |
| Brown-out reset threshold 3 | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 153 |
| Brown-out reset threshold 4 | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 153 |
| Brown-out reset threshold 4 | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 153 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40°C < TA < +130°C | 155 |
| Internal reference voltage spread over the temperature range | ∆VREFINT | 5 | 7.5 | mV | VDD = 3 V | 155 | |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 155 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 155 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C | 155 | |
| 1/4 reference voltage (% of VREFINT) | VREFINT_DIV1 | 24 | 25 | 26 | % | 155 | |
| 1/2 reference voltage (% of VREFINT) | VREFINT_DIV2 | 49 | 50 | 51 | % | 155 | |
| 3/4 reference voltage (% of VREFINT) | VREFINT_DIV3 | 74 | 75 | 76 | % | 155 |
CAD (KiCad official)
- Symbol:
STM32L562CEU6 - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32l562ceu6-etched.step/stm32l562ceu6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l562ceu6.step/stm32l562ceu6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (341 pp, sha256
bc9dcd89da9546a8, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).