Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32L562CEU6

STMicroelectronics · ST Microelectronics · UFQFPN-48(7x7)

STM32L562CEU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VBAT power_in Backup supply (1.55 V to 3.6 V) for the RTC, the external 32 kHz oscillator and the backup registers when VDD is not present.
2 PC13 bidirectional FT I/O supplied through the power switch, which sinks only 3 mA, so in output mode it must not exceed 2 MHz with a 30 pF maximum load and must not be used as a current source; additional functions are WKUP2, RTC_TS/RTC_OUT1 and TAMP_IN1/TAMP_OUT2.
3 PC14-OSC32_IN bidirectional FT I/O on the power switch with the same 3 mA limit (output at most 2 MHz with 30 pF, no current-source use), doubling as the 32 kHz oscillator input OSC32_IN.
4 PC15-OSC32_OUT bidirectional FT I/O on the power switch with the same 3 mA limit (output at most 2 MHz with 30 pF, no current-source use), doubling as the 32 kHz oscillator output OSC32_OUT.
5 PH0-OSC_IN bidirectional FT I/O (PH0) that doubles as the high-speed external oscillator input OSC_IN, with EVENTOUT as its only alternate function.
6 PH1-OSC_OUT bidirectional FT I/O (PH1) that doubles as the high-speed external oscillator output OSC_OUT, with EVENTOUT as its only alternate function.
7 NRST bidirectional Bidirectional reset pin with an embedded weak pull-up resistor; functionality is guaranteed when reset is released down to VBOR0 min.
8 VSSA/VREF- power_in Analog ground; VREF- must always be equal to VSSA, and on this package the pin is bonded to VSSA.
9 VDDA/VREF+ power_in Analog supply of 1.62 V (ADCs/COMPs) or 1.8 V (DACs/OPAMPs) to 3.6 V; VREF+ is double-bonded to VDDA here, so the internal voltage reference buffer is unavailable and must stay disabled, and VREF+ must equal VDDA when VDDA is below 2 V.
10 PA0 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM5_CH1, TIM8_ETR, USART2_CTS/USART2_NSS, UART4_TX, SAI1_EXTCLK and TIM2_ETR alternate functions; additional OPAMP1_VINP, ADC12_IN5, WKUP1 and TAMP_IN2/TAMP_OUT1.
11 PA1 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH2, TIM5_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS/USART2_DE, UART4_RX, OCTOSPI1_DQS and TIM15_CH1N alternate functions; additional OPAMP1_VINM, ADC12_IN6 and TAMP_IN5/TAMP_OUT4.
12 PA2 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH3, TIM5_CH3, USART2_TX, LPUART1_TX, OCTOSPI1_NCS, UCPD1_FRSTX1, SAI2_EXTCLK and TIM15_CH1 alternate functions; additional ADC12_IN7, WKUP4/LSCO and COMP1_INP.
13 PA3 bidirectional TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH4, TIM5_CH4, SAI1_CK1, USART2_RX, LPUART1_RX, OCTOSPI1_CLK, SAI1_MCLK_A and TIM15_CH2 alternate functions; additional OPAMP1_VOUT and ADC12_IN8.
14 PA4 bidirectional TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with OCTOSPI1_NCS, SPI1_NSS, SPI3_NSS, USART2_CK, SAI1_FS_B and LPTIM2_OUT alternate functions; additional ADC12_IN9 and DAC1_OUT1.
15 PA5 bidirectional TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM2_ETR, TIM8_CH1N, SPI1_SCK and LPTIM2_ETR alternate functions; additional ADC12_IN10 and DAC1_OUT2.
16 PA6 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO, USART3_CTS/USART3_NSS, LPUART1_CTS, OCTOSPI1_IO3 and TIM16_CH1 alternate functions; additional OPAMP2_VINP and ADC12_IN11.
17 PA7 bidirectional FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with TIM1_CH1N, TIM3_CH2, TIM8_CH1N, I2C3_SCL, SPI1_MOSI, OCTOSPI1_IO2 and TIM17_CH1 alternate functions; additional OPAMP2_VINM and ADC12_IN12.
18 PB0 bidirectional TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI1_NSS, USART3_CK, OCTOSPI1_IO1, COMP1_OUT and SAI1_EXTCLK alternate functions; additional OPAMP2_VOUT and ADC12_IN15.
19 PB1 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN0, USART3_RTS/USART3_DE, LPUART1_RTS/LPUART1_DE, OCTOSPI1_IO0 and LPTIM2_IN1 alternate functions; additional COMP1_INM and ADC12_IN16.
20 PB2 bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with LPTIM1_OUT, I2C3_SMBA, DFSDM1_CKIN0, OCTOSPI1_DQS and UCPD1_FRSTX1 alternate functions; additional RTC_OUT2 and COMP1_INP.
21 PB10 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH3, LPTIM3_OUT, I2C4_SCL, I2C2_SCL, SPI2_SCK, USART3_TX, LPUART1_RX, TSC_SYNC, OCTOSPI1_CLK, COMP1_OUT and SAI1_SCK_A alternate functions.
22 PB11 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH4, I2C4_SDA, I2C2_SDA, USART3_RX, LPUART1_TX, OCTOSPI1_NCS and COMP2_OUT alternate functions.
23 VSS power_in Ground pin; all VSS pins must always be connected to the external ground within the permitted range.
24 VDD power_in Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks.
25 PB12 bidirectional FT I/O (5 V tolerant) with TIM1_BKIN, I2C2_SMBA, SPI2_NSS, DFSDM1_DATIN1, USART3_CK, LPUART1_RTS/LPUART1_DE, TSC_G1_IO1, OCTOSPI1_NCLK, SAI2_FS_A and TIM15_BKIN alternate functions.
26 PB13 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH1N, LPTIM3_IN1, I2C2_SCL, SPI2_SCK, DFSDM1_CKIN1, USART3_CTS/USART3_NSS, LPUART1_CTS, TSC_G1_IO2, UCPD1_FRSTX2, SAI2_SCK_A and TIM15_CH1N alternate functions.
27 PB14 bidirectional FT_fd I/O (5 V tolerant, Fm+ capable, USB Type-C dead battery function) with TIM1_CH2N, LPTIM3_ETR, TIM8_CH2N, I2C2_SDA, SPI2_MISO, DFSDM1_DATIN2, USART3_RTS/USART3_DE, TSC_G1_IO3, SAI2_MCLK_A and TIM15_CH1 alternate functions; additional UCPD1_DB2.
28 PB15 bidirectional FT_c I/O (5 V tolerant, USB Type-C PD capable) with RTC_REFIN, TIM1_CH3N, TIM8_CH3N, SPI2_MOSI, DFSDM1_CKIN2, SAI2_SD_A and TIM15_CH2 alternate functions; additional UCPD1_CC2.
29 PA8 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with MCO, TIM1_CH1, SAI1_CK2, USART1_CK, SAI1_SCK_A and LPTIM2_OUT alternate functions.
30 PA9 bidirectional FT_fu I/O (5 V tolerant, Fm+ capable, USB function supplied by VDDUSB) with TIM1_CH2, SPI2_SCK, USART1_TX, SAI1_FS_A and TIM15_BKIN alternate functions.
31 PA10 bidirectional FT_fu I/O (5 V tolerant, Fm+ capable, USB function supplied by VDDUSB) with TIM1_CH3, SAI1_D1, USART1_RX, CRS_SYNC, SAI1_SD_A and TIM17_BKIN alternate functions.
32 PA11 bidirectional FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_CH4, TIM1_BKIN2, SPI1_MISO, USART1_CTS/USART1_NSS, FDCAN1_RX and USB_DM alternate functions.
33 PA12 bidirectional FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_ETR, SPI1_MOSI, USART1_RTS/USART1_DE, FDCAN1_TX and USB_DP alternate functions.
34 PA13 (JTMS/SWDIO) bidirectional FT I/O that after reset is the JTMS/SWDIO debug function, with its internal pull-up activated; alternate functions include IR_OUT, USB_NOE, SAI1_SD_B and EVENTOUT.
35 VSS power_in Ground pin; all VSS pins must always be connected to the external ground within the permitted range.
36 VDD power_in Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks.
37 PA14 (JTCK/SWCLK) bidirectional FT I/O that after reset is the JTCK/SWCLK debug function, with its internal pull-down activated; alternate functions include LPTIM1_OUT, I2C1_SMBA, I2C4_SMBA, SAI1_FS_B and EVENTOUT.
38 PA15 (JTDI) bidirectional FT_c I/O (USB Type-C PD capable) that after reset is the JTDI debug function, with its internal pull-up activated; additional UCPD1_CC1 function.
39 PB3 (JTDO/TRACESWO) bidirectional FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with JTDO/TRACESWO, TIM2_CH2, SPI1_SCK, SPI3_SCK, USART1_RTS/USART1_DE, CRS_SYNC and SAI1_SCK_B alternate functions; additional COMP2_INM.
40 PB4 (NJTRST) bidirectional FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) that after reset is the NJTRST debug function with its internal pull-up activated; alternate functions include TIM3_CH1, I2C3_SDA, SPI1_MISO, SPI3_MISO, USART1_CTS/USART1_NSS and TIM17_BKIN; additional COMP2_INP.
41 PB5 bidirectional FT_d I/O (5 V tolerant, USB Type-C PD dead battery function) with LPTIM1_IN1, TIM3_CH2, OCTOSPI1_NCLK, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, USART1_CK, UART5_CTS/UART5_NSS, COMP2_OUT, SAI1_SD_B and TIM16_BKIN alternate functions; additional UCPD1_DB1.
42 PB6 bidirectional FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with LPTIM1_ETR, TIM4_CH1, TIM8_BKIN2, I2C1_SCL, I2C4_SCL, USART1_TX, SAI1_FS_B and TIM16_CH1N alternate functions; additional COMP2_INP.
43 PB7 bidirectional FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with LPTIM1_IN2, TIM4_CH2, TIM8_BKIN, I2C1_SDA, I2C4_SDA, USART1_RX, UART4_CTS, FMC_NL and TIM17_CH1N alternate functions; additional COMP2_INM and PVD_IN.
44 PH3-BOOT0 bidirectional FT I/O (PH3) that carries the BOOT0 function, with EVENTOUT as its only listed alternate function.
45 PB8 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with TIM4_CH3, SAI1_CK1, I2C1_SCL, DFSDM1_CKOUT, SDMMC1_CKIN, FDCAN1_RX, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1 alternate functions.
46 PB9 bidirectional FT_f I/O (5 V tolerant, Fm+ capable) with IR_OUT, TIM4_CH4, SAI1_D2, I2C1_SDA, SPI2_NSS, SDMMC1_CDIR, FDCAN1_TX, SDMMC1_D5, SAI1_FS_A and TIM17_CH1 alternate functions.
47 VSS power_in Ground pin; all VSS pins must always be connected to the external ground within the permitted range.
48 VDD power_in Main supply of 1.71 V to 3.6 V for the I/Os, the internal regulator and the system analog blocks such as reset, power management and clocks.
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (including VDD, VDDA, VDDIO2, VDDUSB, VBAT, VDDSMPS, VREF+) VDDX - VSS -0.3 4 V 147
Input voltage on FT_xxx pins except FT_c (max = Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VDDSMPS)+4.0, 6.0) as printed) VIN -0.3 V 147
Input voltage on FT_c pins VIN -0.3 5.5 V 147
Input voltage on any other pins VIN -0.3 4 V 147
Allowed voltage difference for VREF+ > VDDA VREF+ - VDDA 0.4 V VREF+ > VDDA 147
Variations between different VDDX power pins of the same domain /ΔVDDx/ 50 mV 147
Variations between all the different ground pins (include VREF- pin) /VSSx-VSS/ 50 mV 148
Total current into sum of all VDD power lines (source) ∑IVDD 160 mA 148
Total current out of sum of all VSS ground lines (sink) ∑IVSS 160 mA 148
Maximum current into each VDD power pin (source) IVDD(PIN) 100 mA 148
Maximum current out of each VSS ground pin (sink) IVSS(PIN) 100 mA 148
Output current sunk by any I/O and control pin IIO(PIN) 20 mA except FT_f pins 148
Output current sunk by any FT_f pin IIO(PIN) 20 mA FT_f pin 148
Output current sourced by any I/O and control pin IIO(PIN) 20 mA 148
Total output current sunk by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 148
Total output current sourced by sum of all I/Os and control pins ∑IIO(PIN) 100 mA 148
Injected current on FT_xxx, TT_xx, RST and B pins IINJ(PIN) -5 0 mA except PA4, PA5 148
Injected current on PA4, PA5 IINJ(PIN) -5 0 mA PA4, PA5 148
Total injected current (sum of all I/Os and control pins) ∑/IINJ(PIN)/ 25 mA 148
Storage temperature range TSTG -65 150 °C 149
Maximum junction temperature TJ 150 °C 149
Internal AHB clock frequency fHCLK 0 110 MHz 149
Internal APB1 clock frequency fPCLK1 0 110 MHz 149
Internal APB2 clock frequency fPCLK2 0 110 MHz 149
Standard operating voltage VDD 1.71 3.6 V 149
PG[15:2] I/Os supply voltage VDDIO2 1.08 3.6 V At least one I/O in PG[15:2] used 149
PG[15:2] I/Os supply voltage VDDIO2 0 3.6 V PG[15:2] not used 149
Analog supply voltage VDDA 1.62 3.6 V ADC or COMP used 149
Analog supply voltage VDDA 1.8 3.6 V DAC or OPAMP used 149
Analog supply voltage VDDA 2.4 3.6 V VREFBUF used 149
Analog supply voltage VDDA 0 V ADC, DAC, OPAMP, COMP, VREFBUF not used 149
Backup operating voltage VBAT 1.55 3.6 V 150
USB supply voltage VDDUSB 3 3.6 V USB used 150
USB supply voltage VDDUSB 0 3.6 V USB not used 150
I/O input voltage (max VDDIOx+0.3 as printed) VIN -0.3 V TT_xx I/O 150
I/O input voltage VIN -0.3 5 V FT_c I/O 150
I/O input voltage (max MIN(MIN(VDD, VDDA, VDDIO2, VDDUSB)+3.6 V, 5.5 V) as printed) VIN -0.3 V All I/O except FT_c and TT_xx 150
Ambient temperature, suffix 6 version, maximum power dissipation TA -40 85 °C Suffix 6 version, maximum power dissipation 150
Ambient temperature, suffix 6 version, low-power dissipation TA -40 105 °C Suffix 6 version, low-power dissipation 150
Junction temperature range, suffix 6 version TJ -40 105 °C Suffix 6 version 150
Reset temporization after BOR0 is detected tRSTTEMPO 250 400 µs VDD rising 153
Brown-out reset threshold 0 VBOR0 1.62 1.66 1.7 V Rising edge 153
Brown-out reset threshold 0 VBOR0 1.6 1.64 1.69 V Falling edge 153
Brown-out reset threshold 1 VBOR1 2.06 2.1 2.14 V Rising edge 153
Brown-out reset threshold 1 VBOR1 1.96 2 2.04 V Falling edge 153
Brown-out reset threshold 2 VBOR2 2.26 2.31 2.35 V Rising edge 153
Brown-out reset threshold 2 VBOR2 2.16 2.2 2.24 V Falling edge 153
Brown-out reset threshold 3 VBOR3 2.56 2.61 2.66 V Rising edge 153
Brown-out reset threshold 3 VBOR3 2.47 2.52 2.57 V Falling edge 153
Brown-out reset threshold 4 VBOR4 2.85 2.9 2.95 V Rising edge 153
Brown-out reset threshold 4 VBOR4 2.76 2.81 2.86 V Falling edge 153
Internal reference voltage VREFINT 1.182 1.212 1.232 V -40°C < TA < +130°C 155
Internal reference voltage spread over the temperature range ∆VREFINT 5 7.5 mV VDD = 3 V 155
Average temperature coefficient TCoeff 30 50 ppm/°C -40°C < TA < +130°C 155
Average voltage coefficient VDDCoeff 250 1200 ppm/V 3.0 V < VDD < 3.6 V 155
Long term stability ACoeff 300 1000 ppm 1000 hours, T = 25°C 155
1/4 reference voltage (% of VREFINT) VREFINT_DIV1 24 25 26 % 155
1/2 reference voltage (% of VREFINT) VREFINT_DIV2 49 50 51 % 155
3/4 reference voltage (% of VREFINT) VREFINT_DIV3 74 75 76 % 155

CAD (KiCad official)

  • Symbol: STM32L562CEU6
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32l562ceu6-etched.step / stm32l562ceu6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32l562ceu6.step / stm32l562ceu6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (341 pp, sha256 bc9dcd89da9546a8, retrieved 2026-11-12, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF