main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs stm32f401ccu6: rebuilt as a full factory component page (was a placeholder) · Ray
viewers stm32f401ccu6: viewers · Ray
package.json Publish 0.2.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.2.0 · Ray
stm32f401ccu6-etched.fit.json stm32f401ccu6: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
stm32f401ccu6-etched.glb stm32f401ccu6: rebuilt as a full factory component page (was a placeholder) · Ray
stm32f401ccu6-etched.step stm32f401ccu6: rebuilt as a full factory component page (was a placeholder) · Ray
stm32f401ccu6-hero.glb Publish 0.2.0 · Ray
stm32f401ccu6-hero.overlay.json Publish 0.2.0 · Ray
stm32f401ccu6.glb Publish 0.2.0 · Ray
stm32f401ccu6.kicad_mod Publish 0.1.0 · Ray
stm32f401ccu6.kicad_sym Publish 0.2.0 · Ray
stm32f401ccu6.lbr Publish 0.2.0 · Ray
stm32f401ccu6.step Publish 0.2.0 · Ray

STM32F401CCU6

STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-48(7x7)

STM32F401CCU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VBAT power_in Backup domain supply, 1.65 V-3.6 V. Powers RTC, LSE, and backup registers when VDD is off.
2 PC13 bidirectional General-purpose 5 V-tolerant I/O. Supplied via the backup power switch (max sink 3 mA, 2 MHz / 30 pF limit). Alt functions: EVENTOUT; additional: RTC_TAMP1, RTC_OUT, RTC_TS.
3 PC14/OSC32_IN bidirectional GPIO (FT except in oscillator/analog mode) or low-speed 32.768 kHz LSE crystal input. Backup-domain I/O with limited drive.
4 PC15/OSC32_OUT bidirectional GPIO (FT except in oscillator/analog mode) or 32.768 kHz LSE crystal output. Backup-domain I/O.
5 PH0/OSC_IN bidirectional GPIO or main HSE crystal/clock input (4-26 MHz). FT except in oscillator/analog mode.
6 PH1/OSC_OUT bidirectional GPIO or main HSE crystal output. FT except in oscillator/analog mode.
7 NRST bidirectional Bidirectional device reset input/open-drain output with embedded weak pull-up (~40 kΩ). Active low.
8 VSSA/VREF- power_in Analog ground and negative ADC reference (tied together on this package). Connect to system ground.
9 VDDA/VREF+ power_in Analog supply and positive ADC reference (tied together on this package). 1.7 V-3.6 V. Decouple with 100 nF + 1 µF.
10 PA0-WKUP bidirectional GPIO (FT). Alt: USART2_CTS, TIM2_CH1/TIM2_ETR, TIM5_CH1, EVENTOUT. Additional: ADC1_IN0, WKUP (wake-up from Standby).
11 PA1 bidirectional GPIO (FT). Alt: USART2_RTS, TIM2_CH2, TIM5_CH2, EVENTOUT. Additional: ADC1_IN1.
12 PA2 bidirectional GPIO (FT). Alt: USART2_TX, TIM2_CH3, TIM5_CH3, TIM9_CH1, EVENTOUT. Additional: ADC1_IN2.
13 PA3 bidirectional GPIO (FT). Alt: USART2_RX, TIM2_CH4, TIM5_CH4, TIM9_CH2, EVENTOUT. Additional: ADC1_IN3.
14 PA4 bidirectional GPIO (FT). Alt: SPI1_NSS, SPI3_NSS/I2S3_WS, USART2_CK, EVENTOUT. Additional: ADC1_IN4.
15 PA5 bidirectional GPIO (FT). Alt: SPI1_SCK, TIM2_CH1/TIM2_ETR, EVENTOUT. Additional: ADC1_IN5.
16 PA6 bidirectional GPIO (FT). Alt: SPI1_MISO, TIM1_BKIN, TIM3_CH1, EVENTOUT. Additional: ADC1_IN6.
17 PA7 bidirectional GPIO (FT). Alt: SPI1_MOSI, TIM1_CH1N, TIM3_CH2, EVENTOUT. Additional: ADC1_IN7.
18 PB0 bidirectional GPIO (FT). Alt: TIM1_CH2N, TIM3_CH3, EVENTOUT. Additional: ADC1_IN8.
19 PB1 bidirectional GPIO (FT). Alt: TIM1_CH3N, TIM3_CH4, EVENTOUT. Additional: ADC1_IN9.
20 PB2/BOOT1 bidirectional GPIO (FT). Alt: EVENTOUT. Additional: BOOT1 boot-mode selector (sampled at reset together with BOOT0).
21 PB10 bidirectional GPIO (FT). Alt: SPI2_SCK/I2S2_CK, I2C2_SCL, TIM2_CH3, EVENTOUT.
22 VCAP_1 passive Internal 1.2 V regulator decoupling pin. Connect a 2.2 µF ceramic to VSS (see datasheet Table 15).
23 VSS power_in Digital ground.
24 VDD power_in Digital I/O and core supply, 1.7 V-3.6 V. Decouple with 100 nF per pin plus a bulk cap.
25 PB12 bidirectional GPIO (FT). Alt: SPI2_NSS/I2S2_WS, I2C2_SMBA, TIM1_BKIN, EVENTOUT.
26 PB13 bidirectional GPIO (FT). Alt: SPI2_SCK/I2S2_CK, TIM1_CH1N, EVENTOUT.
27 PB14 bidirectional GPIO (FT). Alt: SPI2_MISO, I2S2ext_SD, TIM1_CH2N, EVENTOUT.
28 PB15 bidirectional GPIO (FT). Alt: SPI2_MOSI/I2S2_SD, TIM1_CH3N, EVENTOUT. Additional: RTC_REFIN.
29 PA8 bidirectional GPIO (FT). Alt: I2C3_SCL, USART1_CK, TIM1_CH1, OTG_FS_SOF, MCO_1, EVENTOUT.
30 PA9 bidirectional GPIO (FT). Alt: I2C3_SMBA, USART1_TX, TIM1_CH2, EVENTOUT. Additional: OTG_FS_VBUS (USB VBUS sense).
31 PA10 bidirectional GPIO (FT). Alt: USART1_RX, TIM1_CH3, OTG_FS_ID, EVENTOUT. Serves as USB OTG ID pin.
32 PA11 bidirectional GPIO (FT). Alt: USART1_CTS, USART6_TX, TIM1_CH4, OTG_FS_DM (USB D−), EVENTOUT.
33 PA12 bidirectional GPIO (FT). Alt: USART1_RTS, USART6_RX, TIM1_ETR, OTG_FS_DP (USB D+), EVENTOUT.
34 PA13/JTMS-SWDIO bidirectional GPIO (FT). Alt: JTMS/SWDIO debug data. Default after reset: SWDIO with internal pull-up.
35 VSS power_in Digital ground.
36 VDD power_in Digital I/O and core supply, 1.7 V-3.6 V.
37 PA14/JTCK-SWCLK bidirectional GPIO (FT). Alt: JTCK/SWCLK debug clock. Default after reset: SWCLK with internal pull-down.
38 PA15/JTDI bidirectional GPIO (FT). Alt: JTDI, SPI1_NSS, SPI3_NSS/I2S3_WS, TIM2_CH1/TIM2_ETR, EVENTOUT. Default after reset: JTDI with pull-up.
39 PB3/JTDO-SWO bidirectional GPIO (FT). Alt: JTDO/SWO trace, SPI1_SCK, SPI3_SCK/I2S3_CK, I2C2_SDA, TIM2_CH2, EVENTOUT.
40 PB4/NJTRST bidirectional GPIO (FT). Alt: NJTRST, SPI1_MISO, SPI3_MISO, I2S3ext_SD, I2C3_SDA, TIM3_CH1, EVENTOUT. Default after reset: NJTRST with pull-up.
41 PB5 bidirectional GPIO (FT). Alt: SPI1_MOSI, SPI3_MOSI/I2S3_SD, I2C1_SMBA, TIM3_CH2, EVENTOUT.
42 PB6 bidirectional GPIO (FT). Alt: I2C1_SCL, USART1_TX, TIM4_CH1, EVENTOUT.
43 PB7 bidirectional GPIO (FT). Alt: I2C1_SDA, USART1_RX, TIM4_CH2, EVENTOUT.
44 BOOT0 input Boot-mode select input (dedicated BOOT0 pad). Also VPP for factory programming. Sampled at reset with BOOT1 to select main flash / system memory / SRAM boot.
45 PB8 bidirectional GPIO (FT). Alt: I2C1_SCL, TIM4_CH3, TIM10_CH1, SDIO_D4, EVENTOUT.
46 PB9 bidirectional GPIO (FT). Alt: SPI2_NSS/I2S2_WS, I2C1_SDA, TIM4_CH4, TIM11_CH1, SDIO_D5, EVENTOUT.
47 VSS power_in Digital ground.
48 VDD power_in Digital I/O and core supply, 1.7 V-3.6 V.
49 EP passive ST p.117 (UFQFPN48 package information, note 3): 'There is an exposed die pad on the underside of the UFQFPN package. It is recommended to connect and solder this back-side pad to PCB ground.'

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (VDD-VSS, incl. VDDA, VDD, VBAT) VDD-VSS -0.3 4 V 57
Input voltage for BOOT0 VIN 9 V 57
Variation between different VDD power pins /ΔVDDx/ 50 mV 57
Variation between all ground pins /VSSX −VSS/ 50 mV 57
Total current into sum of all VDD_x power lines (source) ΣIVDD 160 mA 58
Total current out of sum of all VSS_x ground lines (sink) ΣIVSS -160 mA 58
Maximum current into each VDD_x power line (source) IVDD 100 mA 58
Maximum current out of each VSS_x ground line (sink) IVSS -100 mA 58
Output current sunk by any I/O and control pin IIO 25 mA sink 58
Output current sourced by any I/O and control pin IIO -25 mA source 58
Total output current sunk by sum of all I/O and control pins ΣIIO 120 mA sink 58
Total output current sourced by sum of all I/Os and control pins ΣIIO -120 mA source 58
Injected current on FT pins IINJ(PIN) -5 0 mA FT pins 58
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 58
Storage temperature range TSTG -65 150 °C 58
Maximum junction temperature TJ 125 °C 58
Internal AHB clock frequency (Power Scale3) fHCLK 0 60 MHz Regulator ON, VOS[1:0] = 0x01 59
Internal AHB clock frequency (Power Scale2) fHCLK 0 84 MHz Regulator ON, VOS[1:0] = 0x10 59
Internal APB1 clock frequency fPCLK1 0 42 MHz 59
Internal APB2 clock frequency fPCLK2 0 84 MHz 59
Standard operating voltage VDD 1.7 3.6 V 59
Analog operating voltage (ADC limited to 1.2 M samples) VDDA 1.7 2.4 V ADC limited to 1.2 M samples; must be same potential as VDD 59
Analog operating voltage (ADC limited to 2.4 M samples) VDDA 2.4 3.6 V ADC limited to 2.4 M samples 59
Backup operating voltage VBAT 1.65 3.6 V 59
1.2 V internal voltage on VCAP_1/VCAP_2 (regulator ON) V12 1.08 1.14 1.2 V Regulator ON, VOS[1:0] = 0x01, max frequency 60 MHz 59
1.2 V internal voltage on VCAP_1/VCAP_2 (regulator ON) V12 1.2 1.26 1.32 V Regulator ON, VOS[1:0] = 0x10, max frequency 84 MHz 59
Input voltage on RST and FT pins VIN -0.3 5.5 V 2 V ≤ VDD ≤ 3.6 V 59
Input voltage on RST and FT pins VIN -0.3 5.2 V VDD ≤ 2 V 59
Input voltage on BOOT0 pin VIN 0 9 V 59
Maximum allowed package power dissipation (UFQFPN48) PD 625 mW suffix 6 and 7 59
Ambient temperature, 6 suffix version (maximum power dissipation) TA -40 85 °C 6 suffix version, maximum power dissipation 60
Ambient temperature, 6 suffix version (low power dissipation) TA -40 105 °C 6 suffix version, low power dissipation 60
Junction temperature range, 6 suffix version TJ -40 105 °C 6 suffix version 60
ESR of external capacitor on VCAP_1/VCAP_2 ESR 2 Ω ESR of external capacitor with available VCAP_1 and VCAP_2 pins 61
VDD rise time rate (power-up) tVDD 20 µs/V 61
VDD fall time rate (power-down) tVDD 20 µs/V 61
Programmable voltage detector level (rising edge) VPVD 2.09 2.14 2.19 V PLS[2:0]=000 (rising edge) 62
Programmable voltage detector level (falling edge) VPVD 1.98 2.04 2.08 V PLS[2:0]=000 (falling edge) 62
Programmable voltage detector level (rising edge) VPVD 3.07 3.14 3.21 V PLS[2:0]=111 (rising edge) 62
Programmable voltage detector level (falling edge) VPVD 2.95 3.03 3.09 V PLS[2:0]=111 (falling edge) 62
Power-on/power-down reset threshold (falling edge) VPOR/PDR 1.6 1.68 1.76 V Falling edge 62
Power-on/power-down reset threshold (rising edge) VPOR/PDR 1.64 1.72 1.8 V Rising edge 62
Brownout level 1 threshold (falling edge) VBOR1 2.13 2.19 2.24 V Falling edge 63
Brownout level 1 threshold (rising edge) VBOR1 2.23 2.29 2.33 V Rising edge 63
Brownout level 2 threshold (falling edge) VBOR2 2.44 2.5 2.56 V Falling edge 63
Brownout level 2 threshold (rising edge) VBOR2 2.53 2.59 2.63 V Rising edge 63
Brownout level 3 threshold (falling edge) VBOR3 2.75 2.83 2.88 V Falling edge 63
Brownout level 3 threshold (rising edge) VBOR3 2.85 2.92 2.97 V Rising edge 63
POR reset timing TRSTTEMPO 0.5 1.5 3 ms 63
InRush current on voltage regulator power-on (POR or wakeup from Standby) IRUSH 160 200 mA 63
InRush energy on voltage regulator power-on (POR or wakeup from Standby) ERUSH 5.4 µC VDD = 1.7 V, TA = 105 °C, IRUSH = 171 mA for 31 µs 63
PLL input clock fPLL_IN 0.95 1 2.1 MHz 80
PLL multiplier output clock fPLL_OUT 24 84 MHz 80
PLL VCO output fVCO_OUT 192 432 MHz 80
48 MHz PLL multiplier output clock fPLL48_OUT 48 75 MHz 80
Oscillator frequency (HSE) fOSC_IN 4 26 MHz 76
External user clock source frequency (HSE) fHSE_ext 1 50 MHz 74
Duty cycle (HSE external clock) DuCy(HSE) 45 55 % 74
External user clock source frequency (LSE) fLSE_ext 32.768 1000 kHz 75
Frequency (LSI) fLSI 17 32 47 kHz 79

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: STM32F401CCU6
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated on the KiCad land (body 7 x 7 mm, terminals on the pads, 0.55 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32f401ccu6-etched.step / stm32f401ccu6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f401ccu6.step / stm32f401ccu6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (134 pp, sha256 7b6573ad963ab63b, retrieved 2026-11-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF