Generated by adom_assets · KiCad file format 20240108
SC1632
Raspberry Pi · Development Boards, Kits, Programmers · Raspberry Pi Pico 2 module, 2x20 0.1in through-hole headers (51x21 mm)
SC1632 from Raspberry Pi, in a Raspberry Pi Pico 2 module, 2x20 0.1in through-hole headers (51x21 mm). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GP0 | bidirectional | GPIO0: UART0 TX, I2C0 SDA, SPI0 RX |
| 2 | GP1 | bidirectional | GPIO1: UART0 RX, I2C0 SCL, SPI0 CSn |
| 3 | GND | power_in | Ground |
| 4 | GP2 | bidirectional | GPIO2: I2C1 SDA, SPI0 SCK |
| 5 | GP3 | bidirectional | GPIO3: I2C1 SCL, SPI0 TX |
| 6 | GP4 | bidirectional | GPIO4: UART1 TX, I2C0 SDA, SPI0 RX |
| 7 | GP5 | bidirectional | GPIO5: UART1 RX, I2C0 SCL, SPI0 CSn |
| 8 | GND | power_in | Ground |
| 9 | GP6 | bidirectional | GPIO6: I2C1 SDA, SPI0 SCK |
| 10 | GP7 | bidirectional | GPIO7: I2C1 SCL, SPI0 TX |
| 11 | GP8 | bidirectional | GPIO8: UART1 TX, I2C0 SDA, SPI1 RX |
| 12 | GP9 | bidirectional | GPIO9: UART1 RX, I2C0 SCL, SPI1 CSn |
| 13 | GND | power_in | Ground |
| 14 | GP10 | bidirectional | GPIO10: I2C1 SDA, SPI1 SCK |
| 15 | GP11 | bidirectional | GPIO11: I2C1 SCL, SPI1 TX |
| 16 | GP12 | bidirectional | GPIO12: UART0 TX, I2C0 SDA, SPI1 RX |
| 17 | GP13 | bidirectional | GPIO13: UART0 RX, I2C0 SCL, SPI1 CSn |
| 18 | GND | power_in | Ground |
| 19 | GP14 | bidirectional | GPIO14: I2C1 SDA, SPI1 SCK |
| 20 | GP15 | bidirectional | GPIO15: I2C1 SCL, SPI1 TX |
| 21 | GP16 | bidirectional | GPIO16: SPI0 RX, I2C0 SDA, UART0 TX |
| 22 | GP17 | bidirectional | GPIO17: SPI0 CSn, I2C0 SCL, UART0 RX |
| 23 | GND | power_in | Ground |
| 24 | GP18 | bidirectional | GPIO18: SPI0 SCK, I2C1 SDA |
| 25 | GP19 | bidirectional | GPIO19: SPI0 TX, I2C1 SCL |
| 26 | GP20 | bidirectional | GPIO20: I2C0 SDA |
| 27 | GP21 | bidirectional | GPIO21: I2C0 SCL |
| 28 | GND | power_in | Ground |
| 29 | GP22 | bidirectional | GPIO22: GPIO |
| 30 | RUN | input | RP2350 enable; on-chip ~50 kOhm pull-up to 3.3 V; short low to reset |
| 31 | GP26 | bidirectional | GPIO26: ADC0, I2C1 SDA |
| 32 | GP27 | bidirectional | GPIO27: ADC1, I2C1 SCL |
| 33 | AGND | power_in | Analog ground reference for GPIO26-29 (Figure 2 pin cell reads GND, function cell and p.8 pin list read AGND) |
| 34 | GP28 | bidirectional | GPIO28: ADC2 |
| 35 | ADC_VREF | power_in | ADC power supply and reference voltage, filtered 3.3 V; may take an external reference |
| 36 | 3V3(OUT) | power_out | Main 3.3 V supply from on-board SMPS; keep external load under 300 mA (p.8 text names it 3V3) |
| 37 | 3V3_EN | input | On-board SMPS enable, pulled up to VSYS via 100 kOhm; short low to disable 3.3 V |
| 38 | GND | power_in | Ground |
| 39 | VSYS | power_in | Main system input, 1.8 V to 5.5 V, feeds the on-board SMPS |
| 40 | VBUS | power_in | Micro-USB input voltage (USB connector pin 1), nominally 5 V |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Raspberry Pi |
| Package | Raspberry Pi Pico 2 module, 2x20 0.1in through-hole headers (51x21 mm) |
| Category | Development Boards, Kits, Programmers |
| Pins | 40 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temp Max | 85 | °C | including self-heating | 13 | |||
| Operating Temp Min | -20 | °C | 13 | ||||
| VSYS Min | VSYS | 1.8 | V | 13 | |||
| VSYS Max | VSYS | 5.5 | V | 13 | |||
| VBUS | VBUS | 5 | V | 5 V ± 10% as printed | 13 | ||
| 3V3 output load | 3V3 | 300 | mA | recommended to keep load on this pin less than 300 mA; maximum depends on RP2350 load and VSYS voltage | 10 | ||
| Recommended maximum ambient temperature of operation | 70 | °C | recommended maximum ambient temperature of operation | 13 |
CAD (Adom-generated)
- Symbol:
SC1632 - Footprint:
Adom_Gen:Raspberry_Pi_SC1632_b341e1 - 3D model: generated to fit the land (STEP)
- 3D model files:
sc1632-etched.step/sc1632-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sc1632.step/sc1632.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Raspberry Pi datasheet (24 pp, sha256
cbcfaf881018c686, retrieved 2026-11-19) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: No through-hole carrier land is printed (Figure 5 is the SMT castellation land for the bare SC1631). Derived from Figure 3 (PDF p.8): 2 rows of 20 pins on 2.54 mm pitch, rows 17.78 mm apart, pin 1 to pin 20 span 48.26 mm, board 21 x 51 mm with 1.61 mm side margin; pin numbering per Figure 4 (pin 1 top-left, 20 bottom-left, 21 bottom-right, 40 top-right, USB at top). Pins are standard 0.1in pin headers (p.4 text): drill 1.0 mm, pad 1.7 mm (pin 1 square), the KiCad PinHeader_2.54mm land for those leads. Body 21 x 51 mm centred on the pin grid (48.26 + 2x1.37 = 51, as drawn in Figure 3); h = 1.0 mm board thickness (p.7 text), headers and parts above not dimensioned. The pre-fitted debug header (D1-D3) has no carrier pads.