Generated by kicad-footprint-generator · KiCad file format 20260206
| Name | Last updated |
|---|---|
| docs | |
| viewers | |
| package.json | |
| page.json | |
| README.md | |
| rt8480gs-hero.glb | |
| rt8480gs-hero.overlay.json | |
| rt8480gs.glb | |
| rt8480gs.kicad_mod | |
| rt8480gs.kicad_sym | |
| rt8480gs.lbr | |
| rt8480gs.step |
RT8480GS
Richtek Tech · LED Drivers · SOP-16
RT8480GS from Richtek Tech, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GBIAS | power_out | Internal gate driver bias pin that requires a good bypass capacitor (1µF, 10V rated low ESR typical); about 8.2V at 20mA. |
| 2 | GATE | output | External MOSFET switch gate driver output pin, with 7.5V typical high level at 100µA and 15ns rise/fall into 1nF. |
| 3 | PWMOUT | output | Output pin for the PWM dimming MOSFET driver, with 7.5V typical high level at 1mA. |
| 4 | ISW | input | External MOSFET switch current sense pin, connected to the sense resistor between the external N-MOSFET and ground, with 90mV typical current limit threshold. |
| 5 | PWMDIM | input | Control input for the PWM dimming MOSFET driver, with logic-high of at least 2V and logic-low of at most 0.5V. |
| 6 | ISP | input | LED current sense amplifier positive input. |
| 7 | ISN | input | LED current sense amplifier negative input, with a 190mV voltage threshold between ISP and ISN. |
| 8 | VC | passive | PWM control loop compensation pin, typically with 1.8kΩ in series with 10nF to GND. |
| 9 | ACTL | input | Analog dimming control pin with an effective programming voltage range between 0.3V and 1.2V. |
| 10 | DCTL | input | PWM dimming control pin which, with a 0.47µF filter capacitor on ACTL, converts the PWM duty to analog dimming where VACTL = 1.2V x duty cycle. |
| 11 | SS | passive | Soft-start pin that requires a capacitor of at least 100nF for proper soft-start, charged by 6µA. |
| 12 | EN | input | Active-high chip enable; the chip is in shutdown when this pin voltage is low (at most 0.5V), with 20V absolute maximum. |
| 13 | OVP | input | Over voltage protection pin; the PWM converter turns off when the pin voltage goes higher than 1.2V (1.18V typical threshold). |
| 14 | RSET | passive | Switching frequency set pin with a resistor to GND; 30k sets fSW = 380kHz, and the pin must not be left open. |
| 15 | VCC | power_in | Power supply pin of the chip, 6V to 36V operating range (38V absolute maximum), requiring a low ESR bypass capacitor. |
| 16 | GND | power_in | Ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Richtek Tech |
| Package | SOP-16 |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current | ICC | 6 | 7.2 | mA | VC 0.4V (switching off), VCC = 24V, TA = 25°C | 6 | |
| Shutdown Current | ISHDN | 12 | µA | VEN 0.7V | 6 | ||
| EN Threshold Voltage Logic-High | VIH | 2 | V | 6 | |||
| EN Threshold Voltage Logic-Low | VIL | 0.5 | V | 6 | |||
| EN Input Current | 3 | µA | VEN 3V | 6 | |||
| Current Sense Amplifier Input Threshold (VISP − VISN) | 170 | 190 | 210 | mV | 6 | ||
| ISP / ISN Input Current | IISP / IISN | 20 | µA | VISP − VISN = 0V | 6 | ||
| VC Output Current | IVC | 20 | µA | VISP − VISN = 190mV, 0.5V ≤ VC ≤ 2.4V | 6 | ||
| VC Threshold for PWM Switch Off | 0.7 | V | 6 | ||||
| ACTL Input Current | IACTL | 1 | µA | VACTL = 1.2V | 7 | ||
| ACTL Input Current | IACTL | 10 | µA | VACTL = 0.3V | 7 | ||
| LED Current On Threshold at ACTL | VACTL_ON | 1.25 | V | 7 | |||
| LED Current Off Threshold at ACTL | VACTL_OFF | 0.25 | V | 7 | |||
| DCTL Input Current | IDCTL | 0.5 | µA | 0.3V ≤ VDCTL ≤ 6V | 7 | ||
| Switching Frequency | fSW | 300 | 380 | 460 | kHz | RRSET = 30k | 7 |
| Minimum OFF Time | 280 | ns | Note 6 | 7 | |||
| GBIAS Voltage | VGBIAS | 8.2 | V | IGBIAS = 20mA | 7 | ||
| Gate Voltage High | VGate_H | 7.2 | V | IGate = 20mA | 7 | ||
| Gate Voltage High | VGate_H | 7.5 | V | IGate = 100µA | 7 | ||
| Gate Voltage Low | VGate_L | 0.5 | V | IGate = 100µA | 7 | ||
| GATE Drive Rise and Fall Time | 15 | ns | 1nF load at GATE | 7 | |||
| PWM Switch Current Limit Threshold | ILIM_SW | 90 | mV | 7 | |||
| PWMDIM Threshold Voltage Logic-High | VPWMDIMH | 2 | V | 7 | |||
| PWMDIM Threshold Voltage Logic-Low | VPWMDIML | 0.5 | V | 7 | |||
| PWMOUT Output Voltage High | VPWMOUTH | 7.5 | V | IPWMOUT = 1mA | 7 | ||
| PWMOUT Output Voltage Low | VPWMOUTL | 0.45 | V | IPWMOUT = 100µA | 7 | ||
| PWMOUT Drive Rise and Fall Time | 40 | ns | 1nF load at PWMOUT | 7 | |||
| OVP Threshold | VOVP_th | 1.12 | 1.18 | 1.24 | V | 7 | |
| OVP Input Current | IOVP | 0.1 | µA | 0.7V ≤ VOVP ≤ 1.5V | 7 | ||
| Soft-Start Current | ISS | 6 | µA | VSS ≤ 2V | 7 | ||
| Thermal Shutdown | TSD | 145 | °C | 7 | |||
| Thermal Shutdown Hysteresis | ΔTSD | 10 | °C | 7 | |||
| Supply Input Voltage Range | VCC | 6 | 36 | V | 6 | ||
| Junction Temperature Range | TJ | -40 | 125 | °C | 6 | ||
| Supply Input Voltage | VCC | 38 | V | 6 | |||
| GBIAS, GATE, PWMDIM, PWMOUT | 10 | V | 6 | ||||
| ISW voltage DC | 1 | V | DC | 6 | |||
| ISW voltage transient | 6 | V | < 200ns | 6 | |||
| ISP, ISN voltage DC | 2 | V | DC | 6 | |||
| ISP, ISN voltage transient | 6 | V | < 200ns | 6 | |||
| DCTL, ACTL, OVP Pin Voltage | 8 | V | Note 2 | 6 | |||
| EN Pin Voltage | 20 | V | 6 | ||||
| Power Dissipation | PD | 1.176 | W | SOP-16, TA = 25°C | 6 | ||
| Junction Temperature | TJ | 150 | °C | 6 | |||
| Lead Temperature (Soldering, 10 sec.) | 260 | °C | 6 | ||||
| Storage Temperature Range | -65 | 150 | °C | 6 | |||
| ESD Susceptibility HBM | 2 | kV | Human Body Mode | 6 | |||
| ESD Susceptibility MM | 200 | V | Machine Mode | 6 | |||
| Package Thermal Resistance, Junction to Ambient | θJA | 85 | °C/W | SOP-16, JEDEC 51-3 single-layer board | 6 |
CAD (KiCad official)
- Symbol:
RT8480GS - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Richtek Tech datasheet (17 pp, sha256
c08345e829691669, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).