main
History Download
Ray Publish 0.1.0 b7add1a

RT8480GS

Richtek Tech · LED Drivers · SOP-16

RT8480GS from Richtek Tech, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GBIAS power_out Internal gate driver bias pin that requires a good bypass capacitor (1µF, 10V rated low ESR typical); about 8.2V at 20mA.
2 GATE output External MOSFET switch gate driver output pin, with 7.5V typical high level at 100µA and 15ns rise/fall into 1nF.
3 PWMOUT output Output pin for the PWM dimming MOSFET driver, with 7.5V typical high level at 1mA.
4 ISW input External MOSFET switch current sense pin, connected to the sense resistor between the external N-MOSFET and ground, with 90mV typical current limit threshold.
5 PWMDIM input Control input for the PWM dimming MOSFET driver, with logic-high of at least 2V and logic-low of at most 0.5V.
6 ISP input LED current sense amplifier positive input.
7 ISN input LED current sense amplifier negative input, with a 190mV voltage threshold between ISP and ISN.
8 VC passive PWM control loop compensation pin, typically with 1.8kΩ in series with 10nF to GND.
9 ACTL input Analog dimming control pin with an effective programming voltage range between 0.3V and 1.2V.
10 DCTL input PWM dimming control pin which, with a 0.47µF filter capacitor on ACTL, converts the PWM duty to analog dimming where VACTL = 1.2V x duty cycle.
11 SS passive Soft-start pin that requires a capacitor of at least 100nF for proper soft-start, charged by 6µA.
12 EN input Active-high chip enable; the chip is in shutdown when this pin voltage is low (at most 0.5V), with 20V absolute maximum.
13 OVP input Over voltage protection pin; the PWM converter turns off when the pin voltage goes higher than 1.2V (1.18V typical threshold).
14 RSET passive Switching frequency set pin with a resistor to GND; 30k sets fSW = 380kHz, and the pin must not be left open.
15 VCC power_in Power supply pin of the chip, 6V to 36V operating range (38V absolute maximum), requiring a low ESR bypass capacitor.
16 GND power_in Ground.

Key specifications

Parameter Value
Manufacturer Richtek Tech
Package SOP-16
Category Display Modules / LED Drivers / Display Drivers
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Current ICC 6 7.2 mA VC 0.4V (switching off), VCC = 24V, TA = 25°C 6
Shutdown Current ISHDN 12 µA VEN 0.7V 6
EN Threshold Voltage Logic-High VIH 2 V 6
EN Threshold Voltage Logic-Low VIL 0.5 V 6
EN Input Current 3 µA VEN 3V 6
Current Sense Amplifier Input Threshold (VISP − VISN) 170 190 210 mV 6
ISP / ISN Input Current IISP / IISN 20 µA VISP − VISN = 0V 6
VC Output Current IVC 20 µA VISP − VISN = 190mV, 0.5V ≤ VC ≤ 2.4V 6
VC Threshold for PWM Switch Off 0.7 V 6
ACTL Input Current IACTL 1 µA VACTL = 1.2V 7
ACTL Input Current IACTL 10 µA VACTL = 0.3V 7
LED Current On Threshold at ACTL VACTL_ON 1.25 V 7
LED Current Off Threshold at ACTL VACTL_OFF 0.25 V 7
DCTL Input Current IDCTL 0.5 µA 0.3V ≤ VDCTL ≤ 6V 7
Switching Frequency fSW 300 380 460 kHz RRSET = 30k 7
Minimum OFF Time 280 ns Note 6 7
GBIAS Voltage VGBIAS 8.2 V IGBIAS = 20mA 7
Gate Voltage High VGate_H 7.2 V IGate = 20mA 7
Gate Voltage High VGate_H 7.5 V IGate = 100µA 7
Gate Voltage Low VGate_L 0.5 V IGate = 100µA 7
GATE Drive Rise and Fall Time 15 ns 1nF load at GATE 7
PWM Switch Current Limit Threshold ILIM_SW 90 mV 7
PWMDIM Threshold Voltage Logic-High VPWMDIMH 2 V 7
PWMDIM Threshold Voltage Logic-Low VPWMDIML 0.5 V 7
PWMOUT Output Voltage High VPWMOUTH 7.5 V IPWMOUT = 1mA 7
PWMOUT Output Voltage Low VPWMOUTL 0.45 V IPWMOUT = 100µA 7
PWMOUT Drive Rise and Fall Time 40 ns 1nF load at PWMOUT 7
OVP Threshold VOVP_th 1.12 1.18 1.24 V 7
OVP Input Current IOVP 0.1 µA 0.7V ≤ VOVP ≤ 1.5V 7
Soft-Start Current ISS 6 µA VSS ≤ 2V 7
Thermal Shutdown TSD 145 °C 7
Thermal Shutdown Hysteresis ΔTSD 10 °C 7
Supply Input Voltage Range VCC 6 36 V 6
Junction Temperature Range TJ -40 125 °C 6
Supply Input Voltage VCC 38 V 6
GBIAS, GATE, PWMDIM, PWMOUT 10 V 6
ISW voltage DC 1 V DC 6
ISW voltage transient 6 V < 200ns 6
ISP, ISN voltage DC 2 V DC 6
ISP, ISN voltage transient 6 V < 200ns 6
DCTL, ACTL, OVP Pin Voltage 8 V Note 2 6
EN Pin Voltage 20 V 6
Power Dissipation PD 1.176 W SOP-16, TA = 25°C 6
Junction Temperature TJ 150 °C 6
Lead Temperature (Soldering, 10 sec.) 260 °C 6
Storage Temperature Range -65 150 °C 6
ESD Susceptibility HBM 2 kV Human Body Mode 6
ESD Susceptibility MM 200 V Machine Mode 6
Package Thermal Resistance, Junction to Ambient θJA 85 °C/W SOP-16, JEDEC 51-3 single-layer board 6

CAD (KiCad official)

  • Symbol: RT8480GS
  • Footprint: Package_SO:SOIC-16_3.9x9.9mm_P1.27mm
  • 3D model: SOP-16 (KiCad packages3D, STEP)

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Richtek Tech datasheet (17 pp, sha256 c08345e829691669, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF