Generated by kicad-footprint-generator · KiCad file format 20260206
RFFC2071TR13
Qorvo · RF Mixers · QFN-32-EP(5x5)
RFFC2071TR13 from Qorvo, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ENBL/GPO5 | input | Device enable pin that also serves as general purpose output GPO5; an RC low pass filter may be used on this line to reduce digital noise. |
| 2 | EXT_LO | input | External local oscillator input, which must be driven through an AC-coupling capacitor or transformer with no DC voltage applied; external LO input level is 0 dBm from a 50 ohm source via a 1:1 balun. |
| 3 | EXT_LO_DEC | passive | Decoupling pin for the external local oscillator input. |
| 4 | REXT | passive | External bandgap bias resistor pin; a 51 kOhm resistor must be connected from this pin to ground, as it is sensitive to low frequency noise injection. |
| 5 | ANA_VDD1 | power_in | Analog supply pin, operating range 2.7 V to 3.3 V, requiring good RF decoupling. |
| 6 | LFILT1 | output | Phase detector output and low-frequency noise-sensitive node of the loop filter. |
| 7 | LFILT2 | output | Loop filter op-amp output and low-frequency noise-sensitive node. |
| 8 | LFILT3 | input | VCO control input and low-frequency noise-sensitive node; tuning voltage typically ranges from +0.1 V to +2.4 V. |
| 9 | MODE/GPO6 | bidirectional | Mode select pin that also serves as general purpose output GPO6; it selects which mixer(s) and PLL register bank are active. |
| 10 | REF_IN | input | External reference input, which requires an AC coupling capacitor; typical input is 0.8 Vp-p clipped sine wave with 500 to 1500 mVp-p range and frequency 10 to 104 MHz. |
| 11 | NC | unconnected | No internal connection. |
| 12 | TM | passive | Test mode pin that must be connected to ground. |
| 13 | MIX1_IPN | input | Differential negative input of mixer 1, which must be AC coupled or transformer coupled with no DC applied. |
| 14 | MIX1_IPP | input | Differential positive input of mixer 1, which must be AC coupled or transformer coupled with no DC applied; mixer input frequency range is 30 MHz to 2700 MHz. |
| 15 | GPO1/ADD1 | bidirectional | General purpose output GPO1 that also serves as the MultiSlice address bit ADD1. |
| 16 | GPO2/ADD2 | bidirectional | General purpose output GPO2 that also serves as the MultiSlice address bit ADD2. |
| 17 | MIX1_OPN | output | Differential negative output of mixer 1, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output. |
| 18 | MIX1_OPP | output | Differential positive output of mixer 1, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output. |
| 19 | DIG_VDD | power_in | Digital supply pin, operating range 2.7 V to 3.3 V, which should be decoupled as close to the pin as possible. |
| 20 | NC | unconnected | No internal connection. |
| 21 | NC | unconnected | No internal connection. |
| 22 | ANA_VDD2 | power_in | Analog supply pin, operating range 2.7 V to 3.3 V, requiring good RF decoupling. |
| 23 | MIX2_IPP | input | Differential positive input of mixer 2, which must be AC coupled or transformer coupled with no DC applied. |
| 24 | MIX2_IPN | input | Differential negative input of mixer 2, which must be AC coupled or transformer coupled with no DC applied. |
| 25 | GPO3/FM | bidirectional | General purpose output GPO3 that also serves as frequency control input for binary FSK modulation. |
| 26 | GPO4/LD/DO | bidirectional | General purpose output GPO4 that also serves as lock detect output and, in 4-wire mode, serial data out; GPO output drives up to 20 mA. |
| 27 | MIX2_OPN | output | Differential negative output of mixer 2, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output. |
| 28 | MIX2_OPP | output | Differential positive output of mixer 2, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output. |
| 29 | RESETX | input | Chip reset input, active low; connect to DIG_VDD if asynchronous reset is not required. |
| 30 | ENX | input | Serial interface select input, active low. |
| 31 | SCLK | input | Serial interface clock input for the 3-wire serial bus. |
| 32 | SDATA | input | Serial interface data input for the 3-wire serial bus; in 4-wire mode this pin is the serial data in pin. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Qorvo |
| Package | QFN-32-EP(5x5) |
| Category | RF & Radio |
| Pins | 33 |
CAD (KiCad official)
- Symbol:
RFFC2071TR13 - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
rffc2071tr13-etched.step/rffc2071tr13-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);rffc2071tr13.step/rffc2071tr13.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Qorvo datasheet (23 pp, sha256
b8c4267e36ae68b8, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).