main
History Download
Ray Publish 0.1.0 07190d0

RFFC2071TR13

Qorvo · RF Mixers · QFN-32-EP(5x5)

RFFC2071TR13 from Qorvo, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 ENBL/GPO5 input Device enable pin that also serves as general purpose output GPO5; an RC low pass filter may be used on this line to reduce digital noise.
2 EXT_LO input External local oscillator input, which must be driven through an AC-coupling capacitor or transformer with no DC voltage applied; external LO input level is 0 dBm from a 50 ohm source via a 1:1 balun.
3 EXT_LO_DEC passive Decoupling pin for the external local oscillator input.
4 REXT passive External bandgap bias resistor pin; a 51 kOhm resistor must be connected from this pin to ground, as it is sensitive to low frequency noise injection.
5 ANA_VDD1 power_in Analog supply pin, operating range 2.7 V to 3.3 V, requiring good RF decoupling.
6 LFILT1 output Phase detector output and low-frequency noise-sensitive node of the loop filter.
7 LFILT2 output Loop filter op-amp output and low-frequency noise-sensitive node.
8 LFILT3 input VCO control input and low-frequency noise-sensitive node; tuning voltage typically ranges from +0.1 V to +2.4 V.
9 MODE/GPO6 bidirectional Mode select pin that also serves as general purpose output GPO6; it selects which mixer(s) and PLL register bank are active.
10 REF_IN input External reference input, which requires an AC coupling capacitor; typical input is 0.8 Vp-p clipped sine wave with 500 to 1500 mVp-p range and frequency 10 to 104 MHz.
11 NC unconnected No internal connection.
12 TM passive Test mode pin that must be connected to ground.
13 MIX1_IPN input Differential negative input of mixer 1, which must be AC coupled or transformer coupled with no DC applied.
14 MIX1_IPP input Differential positive input of mixer 1, which must be AC coupled or transformer coupled with no DC applied; mixer input frequency range is 30 MHz to 2700 MHz.
15 GPO1/ADD1 bidirectional General purpose output GPO1 that also serves as the MultiSlice address bit ADD1.
16 GPO2/ADD2 bidirectional General purpose output GPO2 that also serves as the MultiSlice address bit ADD2.
17 MIX1_OPN output Differential negative output of mixer 1, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output.
18 MIX1_OPP output Differential positive output of mixer 1, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output.
19 DIG_VDD power_in Digital supply pin, operating range 2.7 V to 3.3 V, which should be decoupled as close to the pin as possible.
20 NC unconnected No internal connection.
21 NC unconnected No internal connection.
22 ANA_VDD2 power_in Analog supply pin, operating range 2.7 V to 3.3 V, requiring good RF decoupling.
23 MIX2_IPP input Differential positive input of mixer 2, which must be AC coupled or transformer coupled with no DC applied.
24 MIX2_IPN input Differential negative input of mixer 2, which must be AC coupled or transformer coupled with no DC applied.
25 GPO3/FM bidirectional General purpose output GPO3 that also serves as frequency control input for binary FSK modulation.
26 GPO4/LD/DO bidirectional General purpose output GPO4 that also serves as lock detect output and, in 4-wire mode, serial data out; GPO output drives up to 20 mA.
27 MIX2_OPN output Differential negative output of mixer 2, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output.
28 MIX2_OPP output Differential positive output of mixer 2, which must be fed through a center-tapped balun or RF choke to the supply; it is a high impedance constant current output.
29 RESETX input Chip reset input, active low; connect to DIG_VDD if asynchronous reset is not required.
30 ENX input Serial interface select input, active low.
31 SCLK input Serial interface clock input for the 3-wire serial bus.
32 SDATA input Serial interface data input for the 3-wire serial bus; in 4-wire mode this pin is the serial data in pin.
33 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Qorvo
Package QFN-32-EP(5x5)
Category RF & Radio
Pins 33

CAD (KiCad official)

  • Symbol: RFFC2071TR13
  • Footprint: Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm
  • 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: rffc2071tr13-etched.step / rffc2071tr13-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); rffc2071tr13.step / rffc2071tr13.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Qorvo datasheet (23 pp, sha256 b8c4267e36ae68b8, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF