main
History Download
Ray ref5040aidr: one-pass backfill (citation: stored_copy, hero prebuilt (inputs unchanged)) 56f1ef4

REF5040AIDR

Texas Instruments · Voltage Reference · SOIC-8

REF5040AIDR from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DNC unconnected Do Not Connect. This pin is used internally by the factory; it must be left floating in the application. Do not tie to ground, supply, or any other net.
2 VIN power_in Positive supply input. Operating range is (VOUT + 0.2 V) up to +18 V (minimum 2.7 V for VOUT ≤ 2.5 V). Bypass with 1 µF to 10 µF to GND close to the pin.
3 TEMP output Temperature-proportional voltage output. VTEMP ≈ 509 mV + 2.64 mV/°C · T(°C) with ~60 kΩ source impedance. Buffer with a low-drift op-amp (e.g. OPA333/335/376) before driving any load; loading directly introduces measurement error but does not affect VOUT.
4 GND power_in Device ground / 0 V reference. All voltages (VIN, VOUT, TRIM/NR, TEMP) are referred to this pin.
5 TRIM/NR bidirectional Trim and noise-reduction pin - provides access to the internal bandgap node. Connect a 1 µF (or larger) capacitor to GND to form a low-pass filter with the internal 60 kΩ/… resistor network (fc ≈ 10-20 Hz), halving output noise. Alternatively, drive with an external resistor network to trim VOUT by ±15 mV. Leave floating if unused.
6 VOUT output Precision reference voltage output - 4.096 V nominal for REF5040. Load capacitor CL = 1 µF to 50 µF to GND required for stability; ESR of CL must be ≤ 1.5 Ω (recommended 1-1.5 Ω for lowest noise). Can source and sink up to ±10 mA.
7 DNC unconnected Do Not Connect. Factory-use pin; must be left floating. Do not tie to ground, supply, or any other net.
8 NC unconnected No Internal Connection. This pin has no bond to the die and may be left floating or tied to any convenient net (though best practice is to leave it open).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOIC-8
Category PMIC
Pins 8

Ordering variants

  • REF5040AIDR
  • REF5040AIDRAIDT
  • REF5040AIDRIDT
  • REF5040AIDRAIDGK
  • REF5040AIDRAIDGKR
  • REF5040AIDRIDGK
  • REF5040AIDRIDGKR

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (nominal) VOUT 4.096 V 3
Initial Accuracy (Standard-Grade) -0.1 0.1 % 3
Output Voltage Noise 12 μVPP f = 0.1Hz to 10Hz 3
Output Voltage Temperature Drift (Standard-Grade) dVOUT/dT 3 8 ppm/°C 4
Line Regulation (All Other Devices) dVOUT/dVIN 0.1 1 ppm/V VIN = VOUT + 0.2V 4
Line Regulation over temperature dVOUT/dVIN 0.2 1 ppm/V Over Temperature 4
Load Regulation (All Other Devices) dVOUT/dILOAD 20 30 ppm/mA –10mA < ILOAD < +10mA; VIN = VOUT + 0.75V 4
Load Regulation over temperature dVOUT/dILOAD 50 ppm/mA Over Temperature 4
Short-Circuit Current ISC 25 mA VOUT = 0 4
Thermal Hysteresis (Standard-Grade SO-8) 90 ppm Cycle 1 4
Thermal Hysteresis (Standard-Grade SO-8) 50 ppm Cycle 2 4
Long-Term Stability (SO-8) 100 ppm/1000 hr 0 to 1000 hours 4
Long-Term Stability (SO-8) 50 ppm/1000 hr 1000 to 2000 hours 4
TEMP Pin Voltage Output 575 mV At TA = +25°C 4
TEMP Pin Temperature Sensitivity 2.64 mV/°C 4
Turn-On Settling Time 200 μs To 0.1% with CL = 1μF 4
Supply Voltage VS 18 V See Note (1) 4
Quiescent Current IQ 0.8 1 mA 4
Quiescent Current over temperature IQ 1.2 mA Over Temperature 4
Specified Temperature Range TA -40 125 °C Specified range 4
Operating Temperature Range TA -55 125 °C Operating range 4
Thermal Resistance Junction-to-Ambient (SO-8) θJA 150 °C/W 4
Input Voltage VIN 18 V 2
Output Short-Circuit 30 mA 2
Operating Temperature Range (absolute maximum) -55 125 °C 2
Storage Temperature Range -65 150 °C 2
Junction Temperature TJ 150 °C 2
ESD Rating Human Body Model (HBM) 3000 V 2
ESD Rating Charged Device Model (CDM) 1000 V 2

CAD (KiCad official)

  • Symbol: REF5040AIDR
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: ref5040aidr-etched.step / ref5040aidr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ref5040aidr.step / ref5040aidr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (None pp, sha256 3a122a4697547349, retrieved 2026-08-17, tier: manufacturer) (maker link no longer resolves; copy stored with this page)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF