Generated by kicad-footprint-generator · KiCad file format 20260206
REF5040AIDR
Texas Instruments · Voltage Reference · SOIC-8
REF5040AIDR from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DNC | unconnected | Do Not Connect. This pin is used internally by the factory; it must be left floating in the application. Do not tie to ground, supply, or any other net. |
| 2 | VIN | power_in | Positive supply input. Operating range is (VOUT + 0.2 V) up to +18 V (minimum 2.7 V for VOUT ≤ 2.5 V). Bypass with 1 µF to 10 µF to GND close to the pin. |
| 3 | TEMP | output | Temperature-proportional voltage output. VTEMP ≈ 509 mV + 2.64 mV/°C · T(°C) with ~60 kΩ source impedance. Buffer with a low-drift op-amp (e.g. OPA333/335/376) before driving any load; loading directly introduces measurement error but does not affect VOUT. |
| 4 | GND | power_in | Device ground / 0 V reference. All voltages (VIN, VOUT, TRIM/NR, TEMP) are referred to this pin. |
| 5 | TRIM/NR | bidirectional | Trim and noise-reduction pin - provides access to the internal bandgap node. Connect a 1 µF (or larger) capacitor to GND to form a low-pass filter with the internal 60 kΩ/… resistor network (fc ≈ 10-20 Hz), halving output noise. Alternatively, drive with an external resistor network to trim VOUT by ±15 mV. Leave floating if unused. |
| 6 | VOUT | output | Precision reference voltage output - 4.096 V nominal for REF5040. Load capacitor CL = 1 µF to 50 µF to GND required for stability; ESR of CL must be ≤ 1.5 Ω (recommended 1-1.5 Ω for lowest noise). Can source and sink up to ±10 mA. |
| 7 | DNC | unconnected | Do Not Connect. Factory-use pin; must be left floating. Do not tie to ground, supply, or any other net. |
| 8 | NC | unconnected | No Internal Connection. This pin has no bond to the die and may be left floating or tied to any convenient net (though best practice is to leave it open). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-8 |
| Category | PMIC |
| Pins | 8 |
Ordering variants
REF5040AIDRREF5040AIDRAIDTREF5040AIDRIDTREF5040AIDRAIDGKREF5040AIDRAIDGKRREF5040AIDRIDGKREF5040AIDRIDGKR
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (nominal) | VOUT | 4.096 | V | 3 | |||
| Initial Accuracy (Standard-Grade) | -0.1 | 0.1 | % | 3 | |||
| Output Voltage Noise | 12 | μVPP | f = 0.1Hz to 10Hz | 3 | |||
| Output Voltage Temperature Drift (Standard-Grade) | dVOUT/dT | 3 | 8 | ppm/°C | 4 | ||
| Line Regulation (All Other Devices) | dVOUT/dVIN | 0.1 | 1 | ppm/V | VIN = VOUT + 0.2V | 4 | |
| Line Regulation over temperature | dVOUT/dVIN | 0.2 | 1 | ppm/V | Over Temperature | 4 | |
| Load Regulation (All Other Devices) | dVOUT/dILOAD | 20 | 30 | ppm/mA | –10mA < ILOAD < +10mA; VIN = VOUT + 0.75V | 4 | |
| Load Regulation over temperature | dVOUT/dILOAD | 50 | ppm/mA | Over Temperature | 4 | ||
| Short-Circuit Current | ISC | 25 | mA | VOUT = 0 | 4 | ||
| Thermal Hysteresis (Standard-Grade SO-8) | 90 | ppm | Cycle 1 | 4 | |||
| Thermal Hysteresis (Standard-Grade SO-8) | 50 | ppm | Cycle 2 | 4 | |||
| Long-Term Stability (SO-8) | 100 | ppm/1000 hr | 0 to 1000 hours | 4 | |||
| Long-Term Stability (SO-8) | 50 | ppm/1000 hr | 1000 to 2000 hours | 4 | |||
| TEMP Pin Voltage Output | 575 | mV | At TA = +25°C | 4 | |||
| TEMP Pin Temperature Sensitivity | 2.64 | mV/°C | 4 | ||||
| Turn-On Settling Time | 200 | μs | To 0.1% with CL = 1μF | 4 | |||
| Supply Voltage | VS | 18 | V | See Note (1) | 4 | ||
| Quiescent Current | IQ | 0.8 | 1 | mA | 4 | ||
| Quiescent Current over temperature | IQ | 1.2 | mA | Over Temperature | 4 | ||
| Specified Temperature Range | TA | -40 | 125 | °C | Specified range | 4 | |
| Operating Temperature Range | TA | -55 | 125 | °C | Operating range | 4 | |
| Thermal Resistance Junction-to-Ambient (SO-8) | θJA | 150 | °C/W | 4 | |||
| Input Voltage | VIN | 18 | V | 2 | |||
| Output Short-Circuit | 30 | mA | 2 | ||||
| Operating Temperature Range (absolute maximum) | -55 | 125 | °C | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| ESD Rating Human Body Model (HBM) | 3000 | V | 2 | ||||
| ESD Rating Charged Device Model (CDM) | 1000 | V | 2 |
CAD (KiCad official)
- Symbol:
REF5040AIDR - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
ref5040aidr-etched.step/ref5040aidr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ref5040aidr.step/ref5040aidr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (None pp, sha256
3a122a4697547349, retrieved 2026-08-17, tier: manufacturer) (maker link no longer resolves; copy stored with this page) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).