PTH08T230WAD

{
  "slug": "pth08t230wad",
  "version": "0.1.0",
  "type": "component",
  "description": "Texas Instruments DC-DC Power Modules, DIP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "power modules",
    "pth08t230wad",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "pth08t230wad.kicad_sym",
    "pth08t230wad.kicad_mod",
    "pth08t230wad.glb",
    "pth08t230wad.step",
    "pth08t230wad.lbr",
    "docs/hero.png",
    "docs/pth08t230wad-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "pth08t230wad-hero.glb",
    "pth08t230wad-hero.overlay.json"
  ],
  "component": {
    "mpn": "PTH08T230WAD",
    "manufacturer": "Texas Instruments",
    "package": "DIP-10",
    "pin_count": 10,
    "category": "Power Modules",
    "subcategory": "DC-DC Power Modules",
    "datasheet": "https://www.ti.com/cn/lit/gpn/pth08t230w",
    "parts": {
      "symbol": "pth08t230wad.kicad_sym",
      "footprint": "pth08t230wad.kicad_mod",
      "model_3d": "pth08t230wad-hero.glb",
      "model_3d_plain": "pth08t230wad.glb",
      "model_3d_step": "pth08t230wad-etched.step",
      "model_3d_step_plain": "pth08t230wad.step",
      "lbr": "pth08t230wad.lbr"
    },
    "distributor_links": {
      "lcsc": "C485568",
      "digikey": "296-20647-ND",
      "mouser": "595-PTH08T230WAD"
    },
    "distributor_check": {
      "checked_at": "2026-10-08T19:01:45Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "296-20647-ND",
        "status": "found",
        "lifecycle": "Active"
      },
      "mouser": {
        "pn": "595-PTH08T230WAD",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "SmartSync",
        "type": "input",
        "description": "Input that synchronizes the module switching frequency to an external clock; if unused it should be connected to GND (pin 3)."
      },
      {
        "number": "2",
        "name": "VI",
        "type": "power_in",
        "description": "Positive input voltage power node to the module, referenced to the common GND."
      },
      {
        "number": "3",
        "name": "GND",
        "type": "power_in",
        "description": "Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs."
      },
      {
        "number": "4",
        "name": "VO",
        "type": "power_out",
        "description": "Regulated positive power output with respect to GND."
      },
      {
        "number": "5",
        "name": "+Sense",
        "type": "input",
        "description": "Sense input that lets the regulation compensate for voltage drop between the module and the load; for optimal accuracy it must be connected to VO close to the load."
      },
      {
        "number": "6",
        "name": "-Sense",
        "type": "input",
        "description": "Sense input that lets the regulation compensate for voltage drop; for optimal accuracy it must be connected to GND (pin 3) very close to the module, within 10 cm."
      },
      {
        "number": "7",
        "name": "VO Adjust",
        "type": "input",
        "description": "Output voltage adjust pin: a 0.05 W 1% resistor must be connected between this pin and -Sense (pin 6) to set the output above 0.69 V, over a set-point range of 0.69 V to 5.5 V; if left open the output defaults to its lowest value."
      },
      {
        "number": "8",
        "name": "TurboTrans",
        "type": "input",
        "description": "Transient response adjust pin: a 1%, 0.05 W resistor between this pin and +Sense (pin 5) activates TurboTrans; leave open if unused, and external capacitance must never be connected to this pin unless the resistor is a 0 Ω short."
      },
      {
        "number": "9",
        "name": "Track",
        "type": "input",
        "description": "Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active typically 20 ms after VI is applied; if unused it should be connected to VI."
      },
      {
        "number": "10",
        "name": "Inhibit/UVLO",
        "type": "input",
        "description": "Open-collector/drain, negative-logic inhibit input referenced to GND: a low level disables the output (open-circuit leaves the module enabled), and a resistor from this pin to GND (pin 3) raises the input UVLO ON threshold."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: The datasheet does not call this package DIP-10. The only package reference for PTH08T230WAD is the "
        ],
        "pages_sent": 14,
        "cost_usd": 0.0939,
        "at": "2026-10-08T19:01:28"
      },
      "datasheet": {
        "url": "https://www.ti.com/cn/lit/gpn/pth08t230w",
        "pages": 39,
        "sha256": "feea6256e1032766",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 10,
        "described": 10,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "pth08t230wad.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "body on z = 0, through-hole leads below",
        "extents_mm": [
          7.62,
          12.7,
          6.98
        ],
        "zmin_mm": -3.3,
        "centre_offset_mm": 0.127,
        "footprint_binding": "identity",
        "sha256": "d55cf1368e362bcb87f165c0a42ca34c9cdc0e591dae011d929545c8f6b7e91f",
        "checked": "2026-10-08",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "pth08t230wad-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "body on z = 0, through-hole leads below",
        "extents_mm": [
          7.62,
          12.7,
          6.98
        ],
        "zmin_mm": -3.3,
        "centre_offset_mm": 0.127,
        "footprint_binding": "identity",
        "sha256": "5baa69831b79af55fe34b21a6e6cdee6d8f15bd423c59d7a7fa26cf3a41948c5",
        "checked": "2026-10-08",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}