component
PTH08T230WAD
Public Made by Adomby adom
Texas Instruments DC-DC Power Modules, DIP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownPTH08T230WAD
Texas Instruments · DC-DC Power Modules · DIP-10
PTH08T230WAD from Texas Instruments, in a DIP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SmartSync | input | Input that synchronizes the module switching frequency to an external clock; if unused it should be connected to GND (pin 3). |
| 2 | VI | power_in | Positive input voltage power node to the module, referenced to the common GND. |
| 3 | GND | power_in | Common ground for the VI and VO power connections and the 0 Vdc reference for the control inputs. |
| 4 | VO | power_out | Regulated positive power output with respect to GND. |
| 5 | +Sense | input | Sense input that lets the regulation compensate for voltage drop between the module and the load; for optimal accuracy it must be connected to VO close to the load. |
| 6 | -Sense | input | Sense input that lets the regulation compensate for voltage drop; for optimal accuracy it must be connected to GND (pin 3) very close to the module, within 10 cm. |
| 7 | VO Adjust | input | Output voltage adjust pin: a 0.05 W 1% resistor must be connected between this pin and -Sense (pin 6) to set the output above 0.69 V, over a set-point range of 0.69 V to 5.5 V; if left open the output defaults to its lowest value. |
| 8 | TurboTrans | input | Transient response adjust pin: a 1%, 0.05 W resistor between this pin and +Sense (pin 5) activates TurboTrans; leave open if unused, and external capacitance must never be connected to this pin unless the resistor is a 0 Ω short. |
| 9 | Track | input | Analog control input that makes the output follow an external voltage volt-for-volt from 0 V up to the set-point voltage, becoming active typically 20 ms after VI is applied; if unused it should be connected to VI. |
| 10 | Inhibit/UVLO | input | Open-collector/drain, negative-logic inhibit input referenced to GND: a low level disables the output (open-circuit leaves the module enabled), and a resistor from this pin to GND (pin 3) raises the input UVLO ON threshold. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | DIP-10 |
| Category | Power Modules |
| Pins | 10 |
CAD (KiCad official)
- Symbol:
PTH08T230WAD - Footprint:
Package_DIP:DIP-10_W7.62mm - 3D model: DIP-10 (KiCad packages3D, STEP)
- 3D model files:
pth08t230wad-etched.step/pth08t230wad-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pth08t230wad.step/pth08t230wad.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (39 pp, sha256
feea6256e1032766, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).