Generated by kicad-footprint-generator · KiCad file format 20260206
NCV4263-2CPD50R2G
onsemi · Pre-ordered transistors · SOIC-8-EP
NCV4263-2CPD50R2G from onsemi, in a SOIC-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Vin | power_in | Positive power supply input, to be decoupled with a ceramic capacitor to ground; operating input voltage range is 5.5 V to 40 V. |
| 2 | EN | input | Enable input where a low level disables the chip (reducing quiescent current to a 10 µA maximum disable current); connect to Vin if the function is not needed. |
| 3 | RO | output | Reset output, an open-collector output tied to Vout through an internal 30 kΩ pull-up resistor; leave open if the reset function is not needed. |
| 4 | GND | power_in | Power supply ground; connect to the heat sink area at GND potential. |
| 5 | D | passive | Delay timing pin; connect to GND via a ceramic capacitor to set the reset delay time and watchdog trigger time, or leave open if this function is not needed. |
| 6 | RADJ | input | Reset adjust threshold input; connect to GND for the default reset threshold of 93% of Vout, or to an output voltage divider to adjust the threshold. |
| 7 | WDI | input | Watchdog input; rising-edge triggered input for watchdog pulses, connected to GND if the function is not needed. |
| 8 | Vout | power_out | Regulated 5 V output voltage; connect a Cout of at least 22 µF to ground. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | SOIC-8-EP |
| Category | Transistors |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Accuracy | Vout | 4.9 | 5 | 5.1 | V | Vin = 6 V to 40 V, Iout = 5 to 150 mA | 4 |
| Line Regulation | Regline | -25 | 3 | 25 | mV | Iout = 150 mA, Vin = 6 V to 28 V | 4 |
| Load Regulation | Regload | -25 | 25 | mV | Iout = 5 mA to 150 mA | 4 | |
| Dropout Voltage | VDO | 300 | 500 | mV | Iout = 150 mA | 4 | |
| Disable Current | IDIS | 0.066 | 10 | µA | VEN = 0 V, TJ < 125°C | 4 | |
| Quiescent Current | Iq | 0.275 | 1.3 | mA | Iout = 0 mA | 4 | |
| Quiescent Current | Iq | 3 | 18 | mA | Iout = 150 mA | 4 | |
| Quiescent Current | Iq | 11.3 | 23 | mA | Iout = 150 mA, Vin = 4.5 V | 4 | |
| Current Limit | ILIM | 200 | 418 | 500 | mA | Vout = 0.96 x Vout_nom | 4 |
| Enable Input Current | IEN | 5 | 10 | 25 | µA | VEN = 5 V | 4 |
| Watchdog Input Low Time | tWL | 1 | 2 | 3.5 | ms | CD = 100 nF, Vout > VRT, no WDI signal | 4 |
| Watchdog Trigger Time | tWTT | 16 | 20.8 | 27 | ms | CD = 100 nF, Vout > VRT, no WDI signal | 4 |
| Charge Current | ID_charge | 40 | 66.8 | 95 | µA | VD = 1 V, no WDI signal | 4 |
| Discharge Current | ID_disch | 4.4 | 6.54 | 9.4 | µA | VD = 1 V, no WDI signal | 4 |
| Saturation Voltage | VD_sat | 6 | 100 | mV | Vout < VRT, no WDI signal | 4 | |
| Switching Threshold Upper | VthH(D) | 1.45 | 1.7 | 2.05 | V | 4 | |
| Switching Threshold Lower | VthL(D) | 0.2 | 0.34 | 0.55 | V | 4 | |
| Output Voltage Reset Threshold | VRT | 90 | 93 | 96 | % Vout | Vout decreasing, VRADJ = 0 V | 4 |
| Reset Adjust Threshold | Vth(RADJ) | 1.26 | 1.36 | 1.44 | V | 70% of Vout_nom, Vout < (VRT) | 4 |
| Reset Adjustment Range | VRT_range | 70 | 93 | % Vout | 4 | ||
| Reset Output Low Voltage | VROL | 0.01 | 0.4 | V | IRO = 1 mA | 4 | |
| Reset Delay Time | tRD | 1.3 | 2.6 | 4.1 | ms | CD = 100 nF | 4 |
| Reset Reaction Time | tRR | 0.5 | 1.2 | 4 | µs | CD = 100 nF | 5 |
| Thermal Shutdown Temperature | TSD | 150 | 177 | 195 | °C | Iout = 1 mA | 5 |
| Input Voltage (absolute maximum) | Vin | -42 | 45 | V | 3 | ||
| Enable Input Voltage (absolute maximum) | VEN | -42 | 45 | V | 3 | ||
| Output Voltage (absolute maximum) | Vout | -1 | 7 | V | 3 | ||
| Reset Output Voltage (absolute maximum) | VRO | -0.3 | 7 | V | 3 | ||
| Watchdog Input Voltage (absolute maximum) | VWDI | -0.3 | 7 | V | 3 | ||
| Reset Adjust Threshold Voltage (absolute maximum) | VRADJ | -0.3 | 7 | V | 3 | ||
| Delay Timing Output Voltage (absolute maximum) | VD | -0.3 | 7 | V | 3 | ||
| Maximum Junction Temperature (absolute maximum) | TJ | -40 | 150 | °C | 3 | ||
| Storage Temperature | TSTG | -55 | 150 | °C | 3 | ||
| ESD Capability, Human Body Model | ESDHBM | 2 | kV | AEC-Q100-002 (JS-001-2010) | 3 | ||
| ESD Capability, Charged Device Model | ESDCDM | 1 | kV | AEC-Q100-011 (EIA/JESD22-C101) | 3 | ||
| Lead Temperature Soldering Reflow (Pb-Free) | TSLD | 265 | °C | Reflow (SMD styles only), peak | 3 | ||
| Input Voltage (operating range) | Vin | 5.5 | 40 | V | 3 | ||
| Junction Temperature (operating range) | TJ | -40 | 150 | °C | 3 | ||
| Thermal Resistance, Junction-to-Air, SOIC-8 EP | RθJA | 65.1 | °C/W | Note 5: 645 mm2 (1 in2) 1 oz copper, FR4 PCB | 3 | ||
| Thermal Reference, Junction-to-Pad, SOIC-8 EP | ψJPad | 8.7 | °C/W | Note 5: 645 mm2 (1 in2) 1 oz copper, FR4 PCB | 3 |
CAD (KiCad official)
- Symbol:
NCV4263-2CPD50R2G - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm - 3D model: SOIC-8-EP (KiCad packages3D, STEP)
- 3D model files:
ncv4263-2cpd50r2g-etched.step/ncv4263-2cpd50r2g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncv4263-2cpd50r2g.step/ncv4263-2cpd50r2g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (16 pp, sha256
191f55e942163290, retrieved 2026-10-25, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).