Generated by kicad-footprint-generator · KiCad file format 20260206
NCP59749MN2ADJTBG
onsemi · Pre-ordered transistors · VQFN-20-EP(5x5)
NCP59749MN2ADJTBG from onsemi, in a VQFN-20-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | power_out | Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability. |
| 2 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 3 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 4 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 5 | IN | power_in | Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list. |
| 6 | IN | power_in | Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list. |
| 7 | IN | power_in | Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list. |
| 8 | IN | power_in | Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list. |
| 9 | PG | output | Open-drain, active-high Power-Good output that goes high-impedance when VOUT exceeds the PG trip threshold and low-impedance below it; a pull-up of 10 kΩ to 1 MΩ to a supply up to 5.5 V is recommended, and it may be left floating if not needed. |
| 10 | BIAS | power_in | Bias input voltage for the error amplifier, reference and internal control circuits, with a range of 2.7 V to 5.5 V. |
| 11 | EN | input | Enable pin: driving high enables the regulator and driving low puts it into shutdown; it must not be left floating. |
| 12 | GND | power_in | Ground. |
| 13 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 14 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 15 | SS | passive | Soft-start pin; a capacitor to ground sets the start-up time, and if left floating the soft-start ramp time is typically 200 µs. |
| 16 | FB | input | Feedback connection to the center tap of the external resistor divider that sets the output voltage; it must not be left floating. |
| 17 | NC | unconnected | No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane. |
| 18 | OUT | power_out | Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability. |
| 19 | OUT | power_out | Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability. |
| 20 | OUT | power_out | Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | VQFN-20-EP(5x5) |
| Category | Transistors |
| Pins | 21 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | should be connected to the NCP59749 respective pins directly in the device PCB copper layer, not through vias | 8 |
CAD (KiCad official)
- Symbol:
NCP59749MN2ADJTBG - Footprint:
Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm - 3D model: VQFN-20-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
ncp59749mn2adjtbg-etched.step/ncp59749mn2adjtbg-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp59749mn2adjtbg.step/ncp59749mn2adjtbg.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (11 pp, sha256
0e8ff9a7524ccf8c, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).