Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

NCP59749MN2ADJTBG

onsemi · Pre-ordered transistors · VQFN-20-EP(5x5)

NCP59749MN2ADJTBG from onsemi, in a VQFN-20-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OUT power_out Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability.
2 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
3 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
4 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
5 IN power_in Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list.
6 IN power_in Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list.
7 IN power_in Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list.
8 IN power_in Unregulated input to the device; VIN range is 0.8 V to 5.5 V per the features list.
9 PG output Open-drain, active-high Power-Good output that goes high-impedance when VOUT exceeds the PG trip threshold and low-impedance below it; a pull-up of 10 kΩ to 1 MΩ to a supply up to 5.5 V is recommended, and it may be left floating if not needed.
10 BIAS power_in Bias input voltage for the error amplifier, reference and internal control circuits, with a range of 2.7 V to 5.5 V.
11 EN input Enable pin: driving high enables the regulator and driving low puts it into shutdown; it must not be left floating.
12 GND power_in Ground.
13 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
14 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
15 SS passive Soft-start pin; a capacitor to ground sets the start-up time, and if left floating the soft-start ramp time is typically 200 µs.
16 FB input Feedback connection to the center tap of the external resistor divider that sets the output voltage; it must not be left floating.
17 NC unconnected No connection; can be left floating or connected to GND to allow better thermal contact to the top-side plane.
18 OUT power_out Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability.
19 OUT power_out Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability.
20 OUT power_out Regulated output voltage; a total typical capacitance of at least 2.2 µF (ceramic) is needed from this pin to ground to assure stability.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer onsemi
Package VQFN-20-EP(5x5)
Category Transistors
Pins 21

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper should be connected to the NCP59749 respective pins directly in the device PCB copper layer, not through vias 8

CAD (KiCad official)

  • Symbol: NCP59749MN2ADJTBG
  • Footprint: Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm
  • 3D model: VQFN-20-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: ncp59749mn2adjtbg-etched.step / ncp59749mn2adjtbg-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp59749mn2adjtbg.step / ncp59749mn2adjtbg.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (11 pp, sha256 0e8ff9a7524ccf8c, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF