main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ncp1342anacced1r2g: viewers · Ray
ncp1342anacced1r2g-etched.glb Publish 0.1.0 · Ray
ncp1342anacced1r2g-etched.step ncp1342anacced1r2g: factory component page (tier=mfr) · Ray
ncp1342anacced1r2g-hero.glb ncp1342anacced1r2g: hero GLB from the etched model (keeps the MPN mark) · Ray
ncp1342anacced1r2g-hero.overlay.json Publish 0.1.0 · Ray
ncp1342anacced1r2g.glb Publish 0.1.0 · Ray
ncp1342anacced1r2g.kicad_mod Publish 0.1.0 · Ray
ncp1342anacced1r2g.kicad_sym Publish 0.1.0 · Ray
ncp1342anacced1r2g.lbr Publish 0.1.0 · Ray
ncp1342anacced1r2g.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

NCP1342ANACCED1R2G

onsemi · AC-DC Controllers & Regulators · SOP-10

NCP1342ANACCED1R2G from onsemi, in a SOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 Fault input The controller enters fault mode if the voltage on this pin is pulled above or below the fault thresholds, and a precise pull-up current source allows direct interface with an NTC thermistor.
2 FMAX input A resistor to ground sets the maximum switching frequency clamp, and the maximum frequency clamp is disabled if this pin is pulled above 4 V.
3 FB input Feedback input for the QR flyback controller that allows direct connection to an optocoupler.
4 ZCD/OPP input A resistor divider from the auxiliary winding feeds the demagnetization detection comparator and sets the OPP compensation level, with input voltage limited to −0.3 V to VCC + 0.7 V and input current limited to −2/+5 mA.
5 CS input Input to the cycle-by-cycle current limit comparator.
6 GND power_in Ground reference of the controller.
7 DRV output Gate drive pin with high-current capability of −0.5 A / +0.8 A, suitable for driving high gate charge power MOSFETs.
8 VCC power_in Positive supply of the IC: the circuit starts when VCC exceeds 17 V and turns off below 9 V (typical), and the operating range after start-up is 9 V to 28 V (VCC maximum rating 30 V).
9 N/C unconnected Removed for creepage distance; no pin is present at this position on the package.
10 HV input Input for the high-voltage startup and brownout detection circuits, which also contain the line removal detection circuit that safely discharges the X2 capacitors when the line is removed (maximum input voltage 700 V).

Key specifications

Parameter Value
Manufacturer onsemi
Package SOP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Startup Threshold VCC(on) 16 17 18 V dV/dt = 0.1 V/ms; VCC increasing 7
Minimum Operating Voltage VCC(off) 8.5 9 9.5 V VCC decreasing 7
Operating Hysteresis VCC(HYS) 7.5 V VCC(on) − VCC(off) 7
Internal Latch / Logic Reset Level VCC(reset) 4.5 6.5 7.5 V VCC decreasing 7
Transition from Istart1 to Istart2 VCC(inhibit) 0.3 0.7 1.05 V VCC increasing, IHV = 650 µA 7
VCC Overvoltage Protection Threshold VCC(OVP) 27 28 29 V 7
Inhibit Current Sourced from VCC Pin Istart1 0.2 0.5 0.65 mA VCC = 0 V 7
Start-Up Current Sourced from VCC Pin (−40°C to 105°C) Istart2 2.4 3.75 5 mA VCC = VCC(on) − 0.5 V; −40°C to 105°C 7
Start-Up Current Sourced from VCC Pin (−40°C to 125°C) Istart2 2 3.75 5 mA VCC = VCC(on) − 0.5 V; −40°C to 125°C 7
Supply Current, Fault or Latch ICC1 0.115 0.25 mA VCC = VCC(on) − 0.5 V 7
Supply Current, Skip Mode (excluding FB current) ICC2 0.23 0.4 mA VFB = 0 V 7
Supply Current, Operating ICC3 1 1.5 mA fsw = 50 kHz, CDRV = open 7
Rise Time tDRV(rise) 20 40 ns VDRV from 10% to 90% 7
Fall Time tDRV(fall) 5 30 ns VDRV from 90% to 10% 7
High State Voltage VDRV(high2) 10 12 14 V VCC = 30 V, RDRV = 10 kΩ 8
Low State Voltage VDRV(low) 0.25 V VFault = 0 V 8
Open Pin Voltage VFB(open) 4.8 5 5.1 V 8
VFB to Internal Current Setpoint Division Ratio KFB 3.7 4 4.3 , 8
Internal Pull-Up Resistor RFB 17 20 23 kΩ VFB = 0.4 V 8
Current Limit Threshold Voltage VILIM1 0.76 0.8 0.84 V VCS increasing 8
Leading Edge Blanking Duration tLEB1 220 265 330 ns DRV minimum width minus tdelay(ILIM1) 8
Minimum Peak Current (Versions xxxCx) VCS(MIN) 70 100 130 mV Versions xxxCx 9
Abnormal Overcurrent Fault Threshold Voltage VILIM2 1.125 1.2 1.275 V VCS increasing, VFB = 4 V 9
Pull-Up Current Source ICS 0.7 1 1.5 A VCS = VILIM2 − 10 mV 9
Maximum Frequency Clamp (9-pin versions) fMAX1 440 500 560 kHz VFMAX = 0.5 V 8
Maximum Frequency Clamp (9-pin versions) fMAX2 61 70 79 kHz VFMAX = 3.5 V 8
FMAX Disable Threshold (9-pin versions) VFMAX(disable) 3.85 4 4.15 V 8
Maximum On Time ton(MAX) 28 32 40 µs 8
ZCD Threshold Voltage VZCD(trig) 35 60 90 mV VZCD decreasing 8
ZCD Hysteresis VZCD(HYS) 15 25 55 mV VZCD increasing 8
ZCD Clamp Voltage, Positive Clamp VZCD(MAX) 12.4 12.7 13 V IQZCD = 5.0 mA 8
Soft-Start Period tSSTART 2.8 4 5 ms Measured from 1st DRV pulse to VCS = VILIM1 9
Flyback Overload Fault Timer (other versions) tOVLD 120 160 200 ms VCS = VILIM1; other versions (not Exxxx, Fxxxx) 9
Overvoltage Protection (OVP) Threshold VFault(OVP) 2.79 3 3.21 V VFault increasing 9
Overtemperature Protection (OTP) Threshold VFault(OTP_in) 380 400 420 mV VFault decreasing 9
Overtemperature Protection (OTP) Exiting Threshold VFault(OTP_out) 874 910 966 mV VFault increasing 9
Minimum Frequency Clamp fMIN 21.5 25 27 kHz 10
Quiet-Skip Timer (Versions xxAxx) tquiet 1.18 1.25 1.4 ms Versions xxAxx 10
Skip Threshold Vskip 350 400 450 mV VFB decreasing 10
Skip Hysteresis Vskip(HYS) 20 50 70 mV VFB increasing 10
Minimum Peak Current Shift (Versions xxxxC) VMPCM(delta) 250 300 350 mV Versions xxxxC 10
High Voltage Startup Circuit Input Voltage VHV(MAX) -0.3 700 V 6
High Voltage Startup Circuit Input Current IHV(MAX) 20 mA 6
Supply Input Voltage VCC(MAX) -0.3 30 V 6
Supply Input Current ICC(MAX) 30 mA 6
Supply Input Voltage Slew Rate dVCC/dt 1 V/µs 6
Fault Input Voltage VFault(MAX) -0.3 V max = VCC + 0.7 V 6
Fault Input Current IFault(MAX) 10 mA 6
Zero Current Detection and OPP Input Voltage VZCD(MAX) -0.3 V max = VCC + 0.7 V 6
Zero Current Detection and OPP Input Current IZCD(MAX) -2 5 mA 6
Maximum Input Voltage (Other Pins) VMAX -0.3 5.5 V 6
Maximum Input Current (Other Pins) IMAX 10 mA 6
Driver Maximum Voltage VDRV -0.3 V max = VDRV(high) 6
Driver Maximum Current, Source IDRV(SRC) 500 mA 6
Driver Maximum Current, Sink IDRV(SNK) 800 mA 6
Operating Junction Temperature TJ -40 125 °C 6
Maximum Junction Temperature TJ(MAX) 150 °C 6
Storage Temperature Range TSTG -60 150 °C 6
Power Dissipation, D1R2G suffix SOIC-9 PD(MAX) 330 mW TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB 6
Thermal Resistance, junction-to-ambient, D1R2G suffix SOIC-9 RJA 300 °C/W TA = 25°C, 1 oz. Cu, 42 mm² copper clad PCB 6

CAD (KiCad official)

  • Symbol: NCP1342ANACCED1R2G
  • Footprint: Package_SO:SOIC-10_3.9x4.9mm_P1mm
  • 3D model: SOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.75 mm nominal SOIC height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: ncp1342anacced1r2g-etched.step / ncp1342anacced1r2g-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ncp1342anacced1r2g.step / ncp1342anacced1r2g.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: onsemi datasheet (44 pp, sha256 c3d1b8a76d48b18a, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF